Wilbur Curtis TXSG0101S200 Service Manual

Wilbur Curtis Co., inC.

Service Manual – TXSG Server

BREWING INTO THE TXSG SERVER

1. Make sure the control panel screen reads READY TO BREW.

2. Place a clean and empty server centered under the brew cone of your coffee brewer.

3. Remove the top cap from the lid.

4. Fill brew cone with the correct measure of ground coffee.

5. Select the BREW button that matches the brew volume. Press the BREW button to start the

Models

 TXSG0101S600  TXSG1501S600  TXSG0101S200  TXSG1501S200

SERVICING THE THERMOPRO SERVER

1. Completely drain the unit of any coffee.

2. Allow server to cool.

3. Unscrew and remove the lid and tube assembly.

REPLACING THE GAUGE GLASS

The gauge glass can be removed for maintenance and cleaning. Refer to the illustration on page three [3] for assembly sequence.

1. Unscrew the vented cap plug from the top of the gauge glass shield.

2. Carefully lift out the gauge glass tube from the shield and scrub inside the glass with a tube cleaning brush and mild detergent solution. Inspect the glass tube for cracks or chips. If broken, carefully remove all traces of glass and insert a new glass tube.

3. Check the top and bottom washers. Clean the washers. Make sure they are not leaking. Replace if necessary.

4. With the sight glass seated in the gauge glass shield, thread the cap plug onto the top of the shield. Do not overtighten.

REMOVING THE BASE & BOTTOM COVER

To replace the silicone elbow tting for repair or cleaning:

1. Remove the base assembly. Press down on the slide tab in back of the stand and lift off the server.

2. Turn the server upside down and take off the plastic bottom cover, revealing the silicone elbow tting.

3. Remove the wire hose clamps by squeezing the wire ears together. While holding the clamp open, loosen the soft silicone elbow from the liner drain pipe and the faucet shank and pull out elbow.

4. Check for leaks and replace with a new elbow if necessary.

5. Reverse these steps to assemble.

REMOVING THE FAUCET

The faucet will require periodic cleaning and maintenance.

1. Remove the faucet from the body of the server. Unscrew the large nut holding the faucet to the shank to take off the faucet.

2. Disassemble the faucet. Unscrew the bonnet from the body of the faucet.

3. Remove the faucet handle by pressing inward on the seat cup (see photo at right) then unhooking the handle from the center shaft.

4. The seat cup, center shaft and spring will now separate from the bonnet. Clean these parts with a mild detergent solution.

5. While you have these parts disassembled for cleaning, check the condition of the seat cup. Make sure the faucet spring is free of corrosion. Replace these parts with repair kit if necessary (item 19, page 3).

ASSEMBLY

Assemble the unit by reversing the steps for disassembly. Finger tighten wing nut onto faucet. Make sure

clamps are fastened properly and silicone ttings are in good condition. Once assembled, check for leaks around the tting and

faucet.

brew.

6. Allow coffee in the brew cone to completely drip out before removing the coffee server.

WARNING – Thermopro servers may be heavy when lled. Care must be taken when transporting to avoid dropping or spilling.

Cleaning Instructions

1. In a container, mix a mild detergent and warm water solution for cleaning the coffee server.

2. Discard old coffee from the coffee server.

3. Remove and clean the lid.

4. Clean inside the coffee server with a sponge brush soaked in detergent solution.

5. An easy way to remove mineral deposits from the brew cone and the coffee server is to use a pouch or tablet cleaner.

a. Place two tablets or one pouch (refer to manufacturers’ recommendation) into the

brew cone.

b. Place the empty coffee server onto the brew deck.

c. Start a coffee brew cycle by pressing the Brew button on the electronic controller.

d. When the brew cycle has nished, allow the cleaning solution to sit in the coffee

server for a few minutes, then empty the coffee server.

6. Wipe the exterior surfaces with a sponge moistened with the detergent solution. Wipe off coffee spots or stains.

7. Rinse the brew cone and coffee server with running water.

8. Dry the parts and return them to the coffee brewer.

TXSG Coffee Server Precautions:

Do not immerse coffee server in water.

Do not place in dishwasher.

Do not use harsh powders or cleansers containing chlorine.

Do not use a wire brush or pot scour to clean inside liner.

Illustrated Parts List

All parts are common between the 1 gallon and 1½ gallon servers, except where indicated by TXSG15 and TXSG01.

INDEX № PART № DESCRIPTION

WC-37387

WC-56025

WC-56024

WC-1949

WC-2005

WC-2027

WC-2025

WC-37396

WC-56028

WC-2063K

WC-2012-101

WC-2010-101

WC-56030

WC-32004

WC-2006

WC-1951

WC-1938-103K

13A

WC-1938

WC-1841

KIT, CAP, TETHER & SCREW TXSG LID ASSY, TXSG15 LID ASSY, TXSG01 CAP, SHIELD WITH VENT, PLASTIC WASHER, SHIELD CAP 1/8” GLASS, GAUGE 10” TXSG15 GLASS, GAUGE 8” TXSG01 KIT, GLASS GAUGE 10” 3PK TXSG15 TOP SERVER THREADED BLK KIT, BRACKET, GAUGE GLASS RING SHIELD, GAUGE GLASS 10” TXSG15 SHIELD, GAUGE GLASS 8” TXSG01 BOTTOM, PLASTIC BLACK SERVER BALL, PLASTIC RESTRICTOR TXS WASHER, .188 ID X .188 THK BTM NUT, FLANGED, PLASTIC KIT, SHNK, NUT & INST. TXSG 1GAL. & 1.5GAL SHANK, PLASTIC (OLD UNITS) FAUCET, ESP BLACK LOCKING

INDEX № PART № DESCRIPTION

15 16 17 18 19 20 20A 21 22 23 24 25 26 27 28 28A 29 30

WC-64079 WC-1906 WC-1905 WC-4320 WC-3705 WC-56020 WC-56013 WC-61689 WC-43091 WC-2456 WC-4281 WC-58262 WC-37395 WC-2004-101 WC-29082 WC-29082K WC-36076 WC-38281

GUARD, FAUCET TXSG ZINC C’ RING .917 x .760 x .090 NUT, WING PLASTIC 1-1/32-14UNF O-RING, ½” I.D. KIT, FAUCET REPAIR BASE ASSY SERVER STRAIGHT SIDE BASE ASSY, SERVER (OPTIONAL) DRIP, TRAY ASSEMBLY TLXS CLAMP, WIRE HOSE ELBOW, SILICONE STRT SIDE SRV NUT, ½ – NPSM PLASTIC COVER, BOTTOM WHITE PLASTIC KIT, GAUGE ASSY 10” BLK TXSG15 SHIELD BASE GAGE BLACK (OLD UNITS) FITTING, ½”-14 NPSF ASSY(OLD UNITS) KIT, FIT., W/ SILICONE WASH (OLD UNITS) BRUSH, GAUGE GLASS LABEL, DECAF

+ 2 hidden pages