Wilbur Curtis TP15S Installation Manual
THERMOPRO – CLEANING INSTRUCTIONS
DAILY CLEANING INSTRUCTIONS
1. Wipe exterior surfaces with a damp cloth, removing spills
and debris.
2. Slide the brewcone out and
clean it. Thoroughly soap the
sprayhead area with a mild
detergent solution.
3. Rinse and dry the brewcone
and sprayhead area.
4. Drain drip trays of coffee.
5. Dry the tray.
6. Turn on the unit at the front
control panel.
Cleaning the ThermoPro Brewer.…
To ensure the highest quality, best tasting coffee, your ThermoPro
brewer and the servers must be cleaned daily after the last batch.
Regular cleaning and preventive maintenance is essential in keeping
your coffee brewer looking and working like new.
CAUTION – Do not use cleansers, bleach liquids, powders or any other
substance containing chlorine. These products promote corrosion and
will pit the stainless steel. USE OF THESE PRODUCTS WILL VOID
THE WARRANTY.
WEEKLY CLEANING
1. Turn off unit at the power switch, behind the unit. Allow
the brewer to cool.
2. Clean the sprayhead and dome plate area.
a. Remove the sprayhead, unscrewing counterclockwise
from the domeplate.
b. Open the sprayhead with a thin bladed screwdriver and
clean inside.
c. Thoroughly clean and rinse the domeplate area.
d. Clean the brewcone rails with a brush soaked with
detergent. Rinse, then dry the area.
3. Assemble and attach the sprayhead.
THERMOSERVER CLEANING
THERMOPRO BREWING SYSTEMS
CLEANING THE STAINLESS STEEL LINER
1. Rinse out the liner with hot water to remove coffee from the server.
2. Fill the liner with a mild detergent solution and let it stand for 10 to
15 minutes.
3. After about 15 minutes take a sponge and scrub out the
stainless steel liner.
4. Completely drain out the soapy solution from the liner.
5. Fill the airpot with clean water to rinse out any detergent left inside
the unit. Repeat this rinsing several times until the water runs clear
and free of all traces of detergent solution.
CLEANING OF THERMOSERVER PARTS
This insulated server is designed to be easily disassembled for maintenance.
Use three sinks to clean and sterilize airpot parts. Fill one sink with tepid
water containing detergent.
In the second sink pour a
sterilizing solution (follow
product manufacturer’s
instructions for mixing).
Fill the last sink with clean water for rins-
ing.
1.Inthesinklledwiththedetergentsolution,cleantheremovedparts.
Use a small, soft bristled brush to clean hard to reach areas.
CLEANING OF THERMOSERVER FAUCET
1. Twist the faucet handle assembly counterclockwise to remove it from
the faucet. Disassemble the parts from the faucet handle.
2. Clean the seat cup, and other faucet parts with a mild detergent solution. When clean, rinse the parts. Inspect for cracks or tears in the
seat cup. Replace if damaged.
3. Clean the glass gauge.
a.Remove the sight
glass cover by pulling up
and off from the server.
b.Using the narrow
brush provided for this
purpose, brush out the
inside of the glass with a
mild detergent solution.
Rinse the sight glass tube of all detergent.
2. Rinse the parts in clear water.
3.Placethepartsintothesterilizationsinkandimmerseforveminutes.
4. Rinse the solution from the parts.
5. Allow all cleaned parts to completely air dry.
6. Assemble the dried parts onto the server.
11/12/7 . 12.7 . ecn 9374
4/6/04 . 9.0 . edr 4003
c.Replace the sight glass. Make sure silicone seals are seated.
d.Pay special attention to the small gauge glass liquid level hole
on the body of the faucet. You can brush this out with a small pipe
cleaner.
WILBUR CURTIS COMPANY, INC.
6913 Acco Street, Montebello, CA 90640-5403
Telephone: 800-421-6150 323-837-2300
Fax: 323-837-2406
nd the latest on the web at
www.wilburcurtis.com
Printed in U.S.A. 11/07 F-3363 rev A
Loading...