Hydraulic hand test pump
Models CPP700-H and CPP1000-H
for further approvals
see page 2
Applications
■
Simple test pressure generation on site, in the laboratory
or in the workshop
■
For the testing, adjustment and calibration of all types of
pressure measuring instruments
■
Hydraulic pressure generation up to 700 bar (10,000 psi)
or 1,000 bar (14,500 psi)
Calibration technology
WIKA data sheet CT 91.07
Special features
■
Ergonomic handling
■
Precise setting through the ne adjustment valve
■
Compact dimensions
■
Low weight
Description
Application areas
Test pumps serve as pressure generators for the testing,
adjustment and calibration of mechanical and electronic
pressure measuring instruments through comparative
measurements. These pressure tests can take place in the
laboratory or workshop, or on site at the measuring point. The
model CPP700-H and CPP1000-H hand test pumps have
been specically developed for test pressure generation on
site.
Easy operation
By connecting the test item and a suciently accurate
reference pressure measuring instrument to the test pump,
on actuating the pump, the same pressure will act on both
measuring instruments. By comparison of the two measured
values at any given pressure value, a check of the accuracy
and/or adjustment of the pressure measuring instrument
under test can be carried out.
Hand test pump model CPP700-H
Easy handling
The CPP700-H and CPP1000-H hand test pumps, despite
their very compact dimensions, enable simple and accurate
pressure generation of up to a max. of 700 bar (10,000 psi)
or 1,000 bar (14,500 psi) respectively, with an integrated
switching from system pressure to high-pressure generation.
For the precise setting for accurate comparative testing,
the pump features a ne adjustment valve. As a pressure
transmission medium, either hydraulic oil or clean water, free
of calcium carbonate, should be used.
The reference instrument is screwed directly to the top of
the pump, and the test item is connected using a connecting
hose with a G ¼ female thread, included in delivery. The
CPP700-H is delivered with a Minimess
hose system as standard.
®
1620 test item
∙ 05/2016
Data sheets showing similar products:
Test pumps, hydraulic; models CPP1000-X to CPP7000-X; see data sheet CT 91.05
Test pump, pneumatic; model CPP30; see data sheet CT 91.06
Page 1 of 5WIKA data sheet CT 91.07
Specications
Hand test pump
Model CPP700-H Model CPP1000-H
Pressure range 0 ... 700 bar
(0 … 10,000 psi)
Pressure transmission medium Hydraulic uid based on mineral oil or single distilled water
Fluid reservoir 200 cm³
Pressure connections
For reference measuring instrument G ½ female thread, freely rotating.
For test item G ¼ female at test connection hose, length 1 m
Fine adjustment Fine adjustment valve / volume adjustment
Material anodised aluminium, brass, stainless steel, ABS
Sealings FKM and NBR (standard)
Dimensions (L x W x H) 280 x 170 x 120 mm
Weight 1.9 kg
1) Other pressure transmission media on request.
(Water-based hydraulic uids are not suitable)
The connection can be disconnected using an Allen key. Then a G ⅜ female thread is available.
®
(3.28 ft), Minimess
(11.0 x 6.7 x 4.7 in)
(4.2 lbs)
1620 system
0 … 1,000 bar
(0 … 14,500 psi)
G ¼ female, freely rotating at test connection
hose, length 1 m (3.28 ft)
1)
Approvals
Logo Description Country
EAC
■
Pressure equipment directive
■
Machinery directive
- MTSCHS
Permission for commissioning
Approvals and certicates, see website
Eurasian Economic Community
Kazakhstan
Page 2 of 5 WIKA data sheet CT 91.07 ∙ 05/2016
Front view Rear view
1
7
6
5
1
Test item connection hose
CPP700-H: Minimess
2
®
system with a G ¼ female
3
pressure gauge connector
CPP1000-H: G ¼ female
2
Pressure relief valve
3
Plug screw for uid reservoir
4
Fine adjustment valve (volume adjustment)
44 8 1
5
Pump handles
6
Toggle control, system and high-pressure generation
7
Fluid reservoir
8
Connection G ½ female, freely rotating for reference
instruments
9
Blind plug, do not open!
9
7
6
5
Recommended reference pressure measuring instruments
■
Precision digital pressure gauge model CPG1500
Measuring ranges up to 1,000 bar (15,000 psi)
Accuracy 0.05 % of span
For further specications see data sheet CT 10.51
■
Hand-held pressure indicator model CPH6200
Measuring ranges
Accuracy
For further specications see data sheet CT 11.01
WIKA data sheet CT 91.07 ∙ 05/2016 Page 3 of 5
up to 1,000 bar (14,500 psi)
0.2 % of span
■
Hand-held pressure indicator model CPH6300
Measuring ranges up to 1,000 bar (14,500 psi)
Accuracy 0.2 % of span
For further specications see data sheet CT 12.01
■
Precision hand-held pressure indicator model
CPH6400
Measuring ranges up to 6,000 bar (85,000 psi)
Accuracy up to 0.025 % of span
For further specications see data sheet CT 14.01
■
ProcessCalibrator model CPH6000
Measuring ranges up to 8,000 bar (115,000 psi)
Accuracy up to 0.025 % of span
For further specications see data sheet CT 15.01
Calibration software
WIKA-CAL calibration software for creating calibration
certicates or logger protocols
For specications see data sheet CT 95.10
Calibration case
Consisting of:
■
Plastic service case with foam insert
■
Precision digital pressure gauge model CPG1500
■
Hydraulic hand test pump model CPP700-H
Page 4 of 5 WIKA data sheet CT 91.07 ∙ 05/2016
Scope of delivery
CPP700-H
■
Hand test pump, model CPP700-H, oil/water
■
Minimess® test item hose, length 1 m (3.28 ft)
■
Bulkhead connector, G ¼ female
■
Operating instructions
CPP1000-H
■
Hand test pump, model CPP1000-H, oil/water
■
High-pressure test item hose, length 1 m (3.28 ft)
■
Connection, G ¼ female
■
Operating instructions
Accessories
Adapter set
■
Adapter and sealing set, “BSP” for test item hose,
G ¼ male to G ⅛, G ⅜ and G ½ female
■
Adapter and sealing set, “metric” for test item hose,
G ¼ male to M 12 x 1.5, M 20 x 1.5 and Minimess
■
Adapter and sealing set, “NPT” for test item hose,
G ¼ male to ⅛ NPT, ¼ NPT, ⅜ NPT and ½ NPT female
Case
■
Plastic case, incl. foam insert with free spaces for model
CPP700-H or CPP1000-H;
dimensions (W x H x D): 440 x 370 x 140 mm
(17.3 x 14.6 x 5.5 in)
Pressure transmission medium
■
Special oil for CPP1000 and CPP1600 test pump series in
plastic case, contents 1 litre
■
®
Hydraulic uid based on VG22 mineral oil in plastic bottle,
content 1 litre
Other
■
Connection adapter, G ¼ male to G ½ female, material:
stainless steel
■
Sealing and maintenance set for model CPP700-H or
CPP1000-H
■
Spare hose for model CPP700-H or CPP1000-H, length
1 m (3.28 ft)
05/2016 EN
Ordering information
CPP700-H / Package / Adapter set / Case / Special oil / Accessories / Additional ordering information
CPP1000-H / Package / Adapter set / Case / Special oil / Accessories / Additional ordering information
© 12/2008 WIKA Alexander Wiegand SE & Co. KG, all rights reserved.
The specications given in this document represent the state of engineering at the time of publishing.
We reserve the right to make modications to the specications and materials.
WIKA data sheet CT 91.07 ∙ 05/2016 Page 5 of 5
WIKA Alexander Wiegand SE & Co. KG
Alexander-Wiegand-Straße 30
63911 Klingenberg/Germany
Tel. +49 9372 132-0
Fax +49 9372 132-406
info@wika.de
www.wika.de
Loading...