Whynter 4.2 cu.ft. Cigar Cabinet Cooler and Humidor with Humidity
Temperature Control and Spanish Cedar Shelves
MODEL# : CHC-421HC
INSTRUCTION MANUAL
Congratulations on your new Whynter product. To ensure proper operation, please read this Instruction Manual carefully before
using this product. Keep this manual in a safe place for future reference.
Table of Contents
PAGE
Safety Precautions
Parts
Introduction / Technical Data
About Cigars / Terminology
Installation
Operation and Controls
Care and Maintenance
Troubleshooting
3 - 4
5
6
7
8 - 9
10-11
12
13
Warranty Information
14
2
Safety Precautions
Your safety and the safety of others are very important to us.
To reduce the risk of fire, electrical shock, or injury when using your appliance, follow
these basic precautions
APPLIANCE SAFETY
This is the Safety Alert Symbol. This symbol alerts you to potential hazards
that may result in serious injury. All safety messages will follow the Safety
Alert Symbol and either the words” DANGER” or “WARNING”.
Danger means that failure to heed this safety
statement may result in severe injury or death.
Warning means that failure to heed this safety
statement may result in extensive product damage, serious injury, or death.
Caution means that failure to heed this safety
statement may result in minor or moderate injury,
or property or equipment damage.
All safety messages will alert you to know what the potential hazard is, tell you how to reduce the
chance of injury, and let you know what can happen if the instructions are not followed.
IMPORTANT SAFEGUIDES
Before the appliance is used, it must be properly positioned and installed as
described in this manual, please read the manual carefully. To reduce the
risk of fire, electrical shock or injury when using the appliance, follow basic
precaution, including the following:
Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do
not use an extension cord.
Do not use if the power supply cord is damaged. If damaged, it must be replaced by a qualified electri-
cian.
It is recommended that a separate circuit, serving only your appliance be provided. Use receptacles
that cannot be turned off by a switch or pull chain.
Never clean appliance parts with flammable fluids or harsh chemicals. These fumes can create a fire
hazard or explosion.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of the appliance or
any other appliance.
Before proceeding with cleaning and maintenance operations, make sure to unplug the appliance.
Do not connect or disconnect the electric plug with wet hands.
Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in
this manual. All other servicing should be referred to a qualified technician.
3
Safety Precautions
FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL
Use two or more people to move and install the appliance. Failure to do so can result in injury.
When positioning the cigar cooler humidor, ensure that there is at least a 4” clearance at the
sides and a 6” clearance at the back. This will allow for adequate ventilation of any heat generat-
ed by the cigar cooler humidor.
It is recommended you install the appliance in a place where the ambient temperature is between
68º-80ºF. This appliance must be installed in an area protected from the element, such as wind,
rain, water spray or drips.
The appliance should not be located next to ovens, grills or other sources of high heat.
The appliance must be installed with all electrical connections in accordance with state and local
codes.
The fuse (or circuit breaker) size should be 15 amperes.
It is important for the appliance to be leveled in order to work properly. For a stable installation,
make sure the appliance is placed on a flat, level and solid surface.
Ensure that the surface on which the appliance is placed is strong enough to hold the appliance
and the items stored inside.
This appliance is not intended for use by young children or physically-challenged persons without
supervision/assistance. Young children must be supervised to ensure safety around this or any
appliance.
Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may dam-
age or discolor the interior.
Keep fingers out of the “pinch point” areas. Clearance between the doors and between the doors
and cabinet are necessarily small. Be careful closing doors when children are in the area.
The temperature range for this cigar cooler humidor designed to store and age cigars within the
optimal humidity range of 62 % to 75% at a room temperature.
Close the cigar cooler humidor immediately after putting in any items to keep the internal temper-
ature relatively constant.
Avoid placing any objects on top of the appliance.
This is an electrical appliance, to avoid injury from electrical shock do not operate the unit with
wet hands, while standing on a wet surface or while standing in water. Do not use outdoors or in
wet conditions.
When positioning or moving the appliance, ensure that it is not turned up side down or unleveled
greater than 45°.
Never pull the power cord to disconnect it from the outlet. Grasp the plug and pull it from the out-
let.
Never lift, carry or drag the appliance by the power cord.
This appliance is designed for household, non-commercial use only. Any other use will void the
warranty.
Do not plug into the power outlet before set up is completed.
Do not cut or remove the ground prong from the power cord.
Do not move this appliance without emptying it and securing the door in a closed position.
4
Parts and Controls
CHC-421HC
1. Upper Hinge
2. Display
3. Power Switch
4. Temperature Control
5. Humidity Control
6. Light Switch
7. Fan
8. Humidity NTC Cover
9. Cigar Drawer
10. Exhaust window
20
11. Cigar Shelf
12. Temperature Control Box
13. Humidity Tray
14. Foot
15. Lower Hinge
16. Glass
17. Door Seal
18. Stainless Steel Door
19. Handle
20. Lock and Key
5
Introduction to Cigar Cooler Humidors
Our Whynter 4.2 cu.ft. Cigar Cooler Humidor is designed to store and age cigars within the optimal humidity
range 65% to 75% at room temperature. Our humidors contain a humidification system and equipped with a
hygrometer which helps maintain the desired level of humidity. In addition to its main purpose of storing,
preserving and aging cigars for a number of years, Whynter 4.2 cu.ft. Cigar Cooler Humidor is also an
attractive and elegant piece of appliance.
Capacity:
CHC-421HC: 4.2 cu. ft
Freestanding setup
Stainless steel trimmed tempered glass door with lock and sleek black cabinet
Removable Spanish cedar drawers and shelves
Shelf Count
3 cigar drawers
1 half cigar shelf
1 wood trim
Adjustable thermostat with temperature range from 64°F - 72°F
Humidity Control Range: 65% - 75%
Enhanced LCD temperature display
Soft white interior LED lighting with on/off switch
Noise Level - 45 dBA
Unit uses a compressor
Internal fan-forced circulation for even temperature distribution throughout the cabinet
ETL Certified
TECHNICAL DATA
MODEL :
Capacity
Voltage 110V / 60Hz
Current
Input Power 90W
Temperature Control Range
Humidity Control Range
Refrigerant Type
Net Weight
Gross Weight
Unit Dimensions
Packaging Dimensions
CHC-421HC
(4.2 cu.ft /)120L
1.5A
64°F
- 72°F
65% - 75%
R600a (1oz)
88 lbs
105lbs
19.5” W x 22.84” D x 30” H
24.41” W x 27.4” D x 36.97” H
6
About Cigars/Terminology
Amatista
Band
Binder
Blend
Bloom
Bouquet
Bunch
Cap
Cigarillos
Draw
Flag
A glass jar containing 50 (or 25) cigars, sealed and sold "factory fresh".
Ring of paper wrapped around the closed head of most cigars.
Portion of a tobacco leaf that holds the filler leaves together.
The mixture of different types of tobacco in a cigar, including up to five types
of filler leaves, a binder leaf and an outer wrapper.
Harmless white film caused by tobacco oils rising to the surface of the cigar
wrapper. Often indicates a strong taste. (Also called Plume).
Used to describe the smell of a fine cigar and fine wines.
Filler tobacco used to create the body of a cigar.
A circular piece of wrapper leaf used to secure the wrapper at the cigar
head.
Thin, three-inch cigars, popular in Europe, generally machine-made.
Amount of air that gets pulled through a lit cigar. Easy/hot or tight/plugged.
Instead of a cap, flags are an extension of the wrapper leaf used to finish
the head of a cigar. Sometimes tied off in a pigtail or a curly head.
Foot
Head
Hot
Hygrometer
Long Filler
Piercer
Plug
Ring Gauge
Short Filler
Shoulder
The end of the cigar that you light. Often pre-cut.
The closed end of the cigar that you put into your mouth.
A cigar draw that is too easy, often because it has been under-filled.
Device used to measure humidity or percentage of moisture in the air.
Whole tobacco leaves used to fill a cigar; these leaves are long and can run
the length of the cigar's bunch. Long filler should burn evenly and consist-
ently.
Used to cut/pierce a small hole in the end of a cigar (also called a 'lance').
A blockage that prevents a cigar from drawing properly. (Gently massaging
the cigar may relieve a plugged draw).
Diameter of a cigar's barrel, expressed in 64ths of an inch. A half-inch cigar
would be a 32 ring (32/64).
Cigar bunch comprised of scraps of tobacco (parts of leaves and twigs).
Where the cap of the cigar meets the barrel. The cigar will unravel if cut.
Tunneling
Wrapper
Uneven burning of a cigar which occurs when a wrapper does not ash.
High-quality tobacco leaf wound around the finished bunch and binder.
7
Installation
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, or
WARNING
Read all instructions before using the appliance.
DANGER or WARNING: An empty cigar cooler humidor can be a hazardous for chil-
dren or small pets. If disposing of the cigar cooler humidor, remove gasket seals, latches,
lids or the entire door from your unused appliance, or take other action to ensure the ap-
pliance is harmless.
Never allow children to operate, play with, or crawl inside the appliance.
Never clean appliance parts with flammable fluids or harsh chemicals. The fumes can create a fire
hazard or explosion.
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any
other appliance. The fumes can create a fire hazard or explosion.
injury when using your appliance, follow these
basic precautions:
INSTALLATION INSTRUCTIONS
BEFORE USING YOUR APPLIANCE
SEASONING THE UNIT
Before placing any cigars inside of the unit, the inside should be seasoned. This step is very important as cedar is a low density
wood so the hydroscopicity is relatively large. Seasoning will allow the wood to absorb and hold moisture so that it does not
absorb additional moisture once cigars are added.
• Before placing any cigars inside of the unit, wipe the inside of the cabinet walls, drawers and shelves with 100% distilled water.
• Add 100% distilled water into the humidity tray.
Note: The humidity tray should not be filled with propylene glycol solution or humidity beads.
• Ensure the humidity range is over 65% before placing any cigars inside of the unit. This step may take a few days depending on
ambient conditions.
• Load the cabinet with cigars making sure not to block the internal fan(s)/ vents. More moisture may be needed after adding the
cigars as they will naturally absorb some of the moisture from the cabinet.
Remove the exterior and interior packing.
Clean the interior surface with lukewarm water using a soft cloth.
Install the handle on the door
HANDLE BAR
To install the handle, you will need a Phillips head
screwdriver.
1. Open the door.
DOOR
SEAL
SCREWS
DOOR
HANDLE
BAR
2. Locate the two screw holes on the inside of the door
(they may be partially obscured by the door seal so
you may need to remove the door seal).
3. Insert the screws into the screw holes until they stick
out of the front of the door.
4. Line up the holes in the handle with the screws and
give each screw about 2-4 full turns into the handle
bar.
5. Now the turn the screws in all the way, and your
han-dles are installed.
6. Replace seal into door frame.
8
Installation
INSTALLATION OF YOUR APPLIANCE
The appliance is designed for a free standing installation.
WARNING: Do not store or install the app liance outdoors.
CAUTION: This appliance is designed for designed to storing and aging cigars . Do not store perishable
food, medicine or other medical products.
Place your appliance on a hard and level floor that is strong enough to support it when it is fully loaded.
To level your appliance, adjust the leveling legs at the bottom of the appliance if needed.
When positioning the appliance, ensure that there is at least a 4” clearance at the sides and a 6” clearance
at the back. This will allow for adequate ventilation of any heat generated by appliance.
We do not recommend installing the appliance on carpet.
Do not install the appliance near an oven or other heating source. Direct sunlight may affect the acrylic
coating and heat sources may increase electrical consumption. For best performance, do not install the
appliance behind a cabinet door or block the base grille. Extreme cold ambient temperatures may also
cause the appliance not to perform properly.
Avoid locating the appliance in area that may be exposed to excessive moisture.
Plug in the appliance into an exclusive, grounded wall power outlet. Do not under any circumstances cut or
remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding
should be directed toward a qualified electrician or an authorized service center.
ELECTRICAL CONNECTION
WARNING: Improper use of the grounded plug can result in the risk of electrical shock.
If the power cord is damaged, have it replaced by a qualified electrician or contact
Whynter Service Department.
This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly
grounded. The cord should be secured behind the appliance and not left exposed or dangling to prevent
accidental injury.
The appliance should always be plugged into its own individual electrical outlet which has a voltage rating
that matches the rating label on the appliance. This provides the best performance and also prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never unplug the appliance
by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or
replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord
that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be
careful not to damage the power cord.
EXTENSION CORD
Because of potential safety hazards, it is strongly recommended that you do not use an extension cord
with this appliance. However, if you must use an extension cord, it is absolutely necessary that it be a
UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet
and that the electrical rating of the cord be 115 volts and at least 10 amperes.
9
Operation and Controls
Power
Temperature
Humidity
Light
SETTING THE TEMPERATURE
The interior temperature range of 64°F - 72°F (18° - 22°C) can be adjusted in increments of +1 degree. You can
set the temperature by pressing the Temperature button on the control panel. The temperature range cycles back
to 64°F if the temperature button is pressed at 72°F.
SETTING THE HUMIDITY
The interior humidity range of 65% - 75% can be adjusted in increments of +1 percent. You can set the humidity
by pressing the humidity button on the control panel. The interior humidity range cycles back to 65% if the
humidity button is pressed at 75%.
INTERIOR LIGHT
You can turn on and off the interior light by pressing the “Light” button on the control panel.
LEVELING THE APPLIANCE
It is important for your appliance to be leveled in order to work
properly. It can be raised or lowered by rotating each of the feet
leveling legs on the bottom of the machine. If you find that the
surface is not level, rotate the feet leveling legs until the
appliance becomes level .You may need to make several
adjustments to level it. We recommend using a carpenter’s level
to check the machine
Note: This unit has 3 large leveling legs and 1 small leveling leg
under the door hinge.
1. Place a carpenter’s level on top of the product to see if the
appliance is level from front to back and side to side.
2. Adjust the height of the leveling legs as follows: Turn the
leveling leg to the right to lower that side of the refrigerator.
Turn the leveling leg to the left to raise that side of the
refrigerator.
HUMIDITY CONTROL
This appliance is equipped with a maintenance system to assure
correct level of humidity. Fill the humidity tray with 100% distilled
water.
Note: The humidity tray should not be filled with propylene glycol
s
olution or humidity beads. If propylene glycol solution or
humidity beads are preferred, they can be placed in another area
of the cabinet.
Check the water level regularly and refill as needed.
Replace the filters every 3-6 months.
Filters
Distilled water
Suitable water level
Humidity Tray
10
Operation and Controls
NORMAL SOUNDS
The unit is cooled by a compressor. The compressor pumps coolant thr
operating noise. Even when the compressor cuts out, noises caused by changes in temperature and pressure
are unavoidable. Operating noise will be
comes quieter as the operating period continues.
The following noises are normal and occur from time to time:
• Gurgling sound, caused by the refrigerant flowing through the appliance's coils,
• Humming noise made by the compressor. This noise can get louder for brief periods when the motor is
switching on.
• Cracking/popping sounds, resulting from the materials contraction and expansion due to temperature variations,
• Fan operating sound, to circulate the air within the refrigerator cabinet.
• Unusual noise is normally the result of improper installation.
• Where the unit is installed in open-plan kitchen or in partition walls, the level of operating noise will be
heard more acutely. However, this is due to the surrounding architecture and not to the unit.
ough the cooling system, producing
most audible immediately after the compressor comes on. It be-
11
Care and Maintenance
CAUTION: Failure to unplug the appliance could result in electric shock or personal injury
CLEANING YOUR APPLIANCE
Turn off the power, unplug the appliance, and remove all cigars from the appliance and store them in a
suitable place.
Clean the inside, the door seal and the inside of the glass with a clean, damp cloth.
Never use detergents or other substances that emit odors.
Always keep the door closed when cleaning the outside of the appliance. Make sure no detergent odors
penetrate into the appliance.
Clean the side panels and door surfaces with a clean and soft cloth. If necessary, use a moist cloth. Al-
ternatively, use a microfiber cloth.
The humidity tray should be hand-washed with water and detergent. After cleaning, always make sure
the tray is thoroughly rinsed with clean water before replacing.
VACATION TIME
Short vacations: Leave the appliance operating during vacations of less than two days.
Long vacations: If the appliance will not be used for an extended period, remove all items and turn off
the appliance. Clean and dry the interior thoroughly.
MOVING YOUR APPLIANCE
Remove all items inside the appliance.
Securely tape down (we recommend using painter’s tape) all loose items (shelves) inside your appli-
ance.
Turn the adjustable leg up to the base to avoid damage.
Tape (we recommend using painter’s tape) the door shut.
Be sure the appliance stays secure in the upright position during transportation and protect the exterior
of appliance with a blanket, or similar item.
PREPARING FOR STORAGE
If the appliance will not be used for a long time, or is to be
moved to another place, it will be necessary to defrost the unit
and dry the interior.
1. Disconnect the appliance from the power supply by remov-
ing the power plug from the wall socket.
2. Leave the door open to allow for air circulation and to pre-
vent mold, mildew and unpleasant smells.
CAUTION: Store the unit out of the reach of ch ildren. If
you have children, you may want to take additional precau-
tions such as removing the door to prevent a child from be-
ing trapped inside the appliance.
ENERGY SAVING TIPS
The appliance should be located in the coolest area of the room, away from heat producing appliances,
and out of any direct sunlight.
Ensure that the appliance is adequately ventilated. Never obstruct the air vents.
Close the door tightly and do not open the appliance too frequently or for a long period of time.
Store the content in an organized way.
Do not over-fill the appliance to allow air to circulate.
12
Troubleshooting
Problem Possible Causes Solutions
The appliance does not operate
The appliance is not reaching the
desired temperature
Frost forming inside the appliance
The appliance turns itself on and
off frequently
There is a power failure.
The appliance is not plugged in.
A house fuse has blown or the circuit
breaker is tripped.
The appliance is placed too close to a
heat source
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
The environment is too humid.
The ambient temperature is too low.
The door is opened too frequently for a
long period of time.
Drawer(s) blocking internal fan.
Items are blocking the internal fan.
The ambient (room) temperature is too low
or high.
A large amount of contents has been
added to the appliance.
The door is opened too often.
The door is not closed completely.
Ensure the appliance is plugged in and the
power outlet has power.
Replace the broken fuse or reset the breaker.
Adjust the temperature.
Keep the appliance away from sunshine or
other heat sources.
Close the door tightly and do not open the
door too frequently or for a long period of time.
Ensure the door gasket is not loose.
Although this unit uses an auto-defrost sys-
tem, under certain conditions, manual defrosting may required. If frost builds up, try
running the cooler on a warmer tempera-ture
setting.
Close the door tightly and do not open the door
too frequently or for a long period of time.
Unplug the unit to allow the frost to melt.
Move items so they do not block the fan or
exhaust window
Decrease or increase the ambient (room)
temperature.
To minimize internal temperature fluctuation,
do not add large amount of contents at once.
Close the door tightly and do not open the door
too frequently or for a long period of time.
Ensure the door gasket is not loose.
The appliance makes too much
noise
The door does not close properly
Condensation builds up on the
glass door.
The door does not close
properly
The door gasket does not seal proper-ly.
If the noise is from the fan, it may be
normal operating noise.
Contraction and expansion of the in-
side walls may cause popping and
crackling noises.
The appliance is not level.
The appliance is not level.
The door was reversed and not
properly installed.
The shelves are out of position .
Ambient temperature or humidity is
high.
The shelves are out of position
The fan makes normal fan noises.
Some popping or cracking noises are nor-mal.
They are caused by expansion and contraction
of the inside walls due to tem-perature
changes.
Make sure the unit is on a hard and level
surface. Do not place the appliance on car-pet.
Make sure the appliance is on a hard and
level surface. Avoid placing the appliance on
a carpeted or soft surface.
Reinstall door.
Correctly install the shelves.
Lower the room humidity by a dehumidifier or
air conditioner.
Reposition the shelves
13
ONE YEAR LIMITED WARRANTY
This WHYNTER appliance is warranted, to the original owner within the 48 continental states, for one year from
the date of purchase against defects in material and workmanship under normal use and service. When making a
warranty claim, please have the original bill or invoice of purchase with purchase date available. Should your
WHYNTER appliance prove defective within one year from the date of purchase, return the defective part or unit,
freight prepaid (within two months of purchase; after two months to one year, customer will be responsible for
freight cost to Whynter’s service department), along with an explanation of the claim to Whynter LLC. A return
authorization number issued by Whynter is required for all warranty claims and returns. Please package the
WHYNTER appliance carefully in its original packaging material to avoid damage in transit. The original box and
packaging material should be retained, as Whynter is not responsible for the cost of replacement packaging.
Under this warranty, Whynter will repair or replace any parts found defective at our discretion. This warranty is not
transferable. After the expiration of the warranty, the cost of labor and parts will be the responsibility of the original
owner of the unit.
THIS WARRANTY DOES NOT COVER:
∧ Acts of God, such as fire, flood, hurricanes, earthquakes and tornadoes.
∧ Improper power supply such as power surge, low voltage, defective household wiring or
inadequate fuses.
∧ Use in commercial or industrial applications
∧ Damage, accidental or otherwise, to the WHYNTER appliance while in the possession of
a consumer not caused by a defect in material or workmanship;
∧ Damage caused by consumer misuse, tampering, or failure to follow the care and special
handling provisions in the instructions.
∧ Damage to the finish of the case, or other appearance parts caused by wear.
∧ Damage caused by repairs or alterations to the product by anyone other than authorized
by the manufacturer.
∧ Removal, Replacement Packaging, Freight and Insurance cost for the warranty service.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER'S SOLE AND EXCLUSIVE
REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. WHYNTER SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY.
SOME STATES AND PROVINCES DO NOT AL-LOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO
THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRIT-TEN WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO
STATE.
Please retain the original proof of purchase in order to obtain warranty services.
Warranty begins from the original date of purchase.
To obtain service or information, contact
Whynter LLC via email at support@whynter.com or call
866-WHYNTER.
Product contents and specifications may change without notice.
Copyright © 2020 Whynter LLC
WWW.WHYNTER.COM
Loading...