Whynter BBR-148SB 24 inch Built-In 140 Can Undercounter Stainless Steel
Beverage Refrigerator with Reversible Door, Digital Control, Lock and Carbon Filter
Model # : BBR-148SB
INSTRUCTION MANUAL
Table of Contents
PAGE
Safety Precautions
Parts
Product Features
Installation
Operation and Controls
Storage
Care and Maintenance
Troubleshooting
Warranty Information
3 - 4
5
6
7 - 9
10 - 11
12
13
14 - 15
16
2
Safety Precautions
To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic
precautions:
APPLIANCE SAFETY
Your safety and the safety of others are very important to us.
This is the Safety Alert Symbol. This symbol alerts you to potential hazards that may serious
injury. All safety messages will follow the Safety Alert Symbol and either the word "DANGER"
All safety messages will alert you to know what the potential hazard is, tell you how to reduce the chance
of injury, and let you know what can happen if the instructions are not followed.
or "WARNING"
WARNING
CAUTION
Danger means that failure to heed this safety
statement may result in severe injury or death.
Warning means that failure to heed this safety
statement may result in extensive product damage,
serious injury, or death.
Caution means that failure to heed this safety
statement may result in minor or moderate injury, or
property or equipment damage.
IMPORTANT SAFETY GUIDELINE
Before the appliance is used, it must be properly positioned and installed as described in
this manual, please read the manual carefully. To reduce the risk of fire, electrical shock
or injury when using the appliance, follow basic precaution, including the following:
•
Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not
use an extension cord.
•
Do not use if the power supply cord is damaged. If damaged, it must be replaced by a qualified electrician.
•
It is recommended that a separate circuit, serving only your appliance be provided. Use receptacles that
cannot be turned off by a switch or pull chain.
•
Never clean appliance parts with flammable fluids or harsh chemicals. These fumes can create a fire hazard or
explosion.
•
Do not store flammable materials or liquids near the appliance.
•
Before proceeding with cleaning and maintenance operations, make sure to unplug the appliance.
•
Do not connect or disconnect the electric plug with wet hands.
3
Safety Precautions
•Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual.
All other servicing should be referred to a qualified technician.
•This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a) which is environmentally
friendly, but flammable. It does not damage the ozone layer, nor does it increase the greenhouse effect. Care must
be taken during transportation and setting up of the appliance that no parts of the cooling system are damaged.
Leaking coolant can ignite and may damage the eyes.
In the event of leakage:
- Avoid open flames and anything which creates a spark
- Disconnect from the mains
- Air the room in which the appliance is located for several minutes and contact the Service Department for
advice
FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL
•Use two or more people to move and install the appliance. Failure to do so can result in injury.
•To ensure proper ventilation for your appliance, the front of the appliance must be completely unobstructed.
•Choose a well-ventilated area with temperatures above 60°F (16°C) and below 90°F (32°C).
•This appliance must be installed in an area protected from the element, such as wind, rain, water spray or drips.
•The appliance should not be located next to ovens, grills or other sources of high heat.
•The appliance must be installed with all electrical connections in accordance with state and local codes.
•The fuse (or circuit breaker) size should be 15 amperes.
•It is important for the appliance to be leveled in order to work properly. For a stable installation, make sure the
appliance is placed on a flat, level and solid surface.
•Ensure that the surface on which the appliance is placed is strong enough to hold the appliance and the items
stored inside.
•Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may damage or discolor the
interior.
•Keep fingers out of the “pinch point” areas. Clearance between the door and cabinet are relatively small. Be
careful closing the door when children are in the area.
•This beverage refrigerator is designed to store beverage cans and bottles. If food is stored inside, ensure that
there is sufficient airflow between items. Please note that the temperature range for this beverage refrigerator is
optimized for beverage storage. Perishable food items may require a different storage environment and is not
recommended.
•Do not place hot food or beverages into the appliance.
•Close the beverage refrigerator door immediately after placing items inside to keep the internal temperature
relatively constant.
•Avoid placing any objects on top of the appliance.
•This is an electrical appliance, to avoid injury from electrical shock do not operate the unit with wet hands, while
standing on a wet surface or while standing in water. Do not use outdoors or in wet conditions.
•When positioning or moving the appliance, ensure that it is not turned upside down or unleveled greater than
45°. If the appliance does not remain in an upright position, allow it to sit upright for a minimum of 4 hours to
allow the refrigerant to settle.
•Never pull the power cord to disconnect it from the outlet. Grasp the plug and pull it from the outlet.
•Never lift, carry or drag the appliance by the power cord.
•This appliance is designed for household, non-commercial use only. Any other use will void the warranty.
•Do not plug into the power outlet before set up is completed.
•Do not move this appliance without emptying it and securing the door in a closed position.
4
Parts
BBR-148SB
1
2
6
10
4
3
5
7
11
1. Control Panel Temperature
Control/Light
2. Top Hinge
3. Shelves (3 big and 1 small )
6. Stainless Steel Door
7. Handle
8. Cylinder lock
12
8
9
13
11. Keys
12. Drip Tray (Rear)
13. Activated Carbon
Filter (inside cabinet)
4. Door Gasket
5. Front Vent
9. Four Adjustable Legs
10. Interior Light
5
Product Features
The Whynter BBR-148SB Beverage Refrigerator is a sophisticated addition to any home and perfect for cooling and
storing your favorite beers and canned beverages. With its reversible and elegant full glass door, this beverage
refrigerator blend well and accent any décor.
Built-In Installation Ready
Its standard counter height makes it ideal for in-cabinet installation and is a favorite to replace that old trash compactor
space. The front-venting design allows you to install this beverage refrigerator under a kitchen counter or cabinet for a
seamless appearance.
Digital Temperature Control and Soft Internal Lighting
Effortlessly control the LED light and temperature settings of your beverage refrigerator using the digital control panel.
While the see-through tempered double pane glass door displays your beverage collection, this unit is also
equipped with an interior light that makes it easy to find exactly what you’re looking for.
Balanced Cooling and Auto Defrost
Features fan-forced circulation to maintain an evenly-cooled space ensuring consistent temperatures throughout the
interior for more effective and efficient operation. The auto defrost feature also allows for maintenance-free continuous
operation (we still recommend powering the unit off during extended periods of non-usage).
Reversible Door with Lock
This beverage refrigerator has the capability of the door opening from either the left or right side, if you prefer a
certain direction or would like the unit to follow the flow of your kitchen design. The cylinder door lock provides
protection and additional security from unauthorized access to your beverage refrigerator.
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Capacity: 140 standard 12 oz. can
Built-in/Freestanding installation
Stainless trimmed glass door with sleek black cabinet
Touch screen control with temperature range from 34°F – 54°F
Environment friendly refrigerant
Activated carbon filter eliminates odors
Double tempered glass panel
Reversible door orientation
Soft interior LED lighting with on/off switch
Equipped with activated carbon filter ensures optimum air quality and eliminates odors
Internal fan-forced circulation for even temperature distribution throughout the cabinet
Cylinder lock and two keys
Fahrenheit and Celsius degree temperature indicators
Three big chrome-plated flat shelves with black plastic plate front end
TECHNICAL DATA
Model:
Capacity :
Voltage:
Power Consumption:
Temperature Range:
Net Weight:
Gross Weight:
Unit Dimension:
Packaging Dimension:
Refrigerant:
23.4" W x 22.4" D x 32.3" H
27.2" W x 26.5" D x 38.6" H
BBR-148SB
140 standard 12 oz. can
115V /60Hz
85W / 0.9A
34°F - 54°F
121 lbs
139 lbs
R600a
6
Installation
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, or injury when
WARNING
• Read all instructions before using the appliance.
• DANGER or WARNING: An empty beverage refrigerator can be a hazardous for children or small pets. If
disposing of the beverage refrigerator, remove gasket seals, latches, lids or the entire door from your unused
appliance, or take other action to ensure the beverage refrigerator is harmless.
• Never allow children to operate, play with, or crawl inside the appliance.
• Never clean appliance parts with flammable fluids or harsh chemicals. The fumes can create a fire hazard or explosion.
• Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance.
The fumes can create a fire hazard or explosion.
using your appliance, follow these basic precautions:
INSTALLATION INSTRUCTIONS
BEFORE USING YOUR APPLIANCE
• Remove the exterior and interior packing.
• Before connecting the appliance to the power source, let it stand upright for approximately 4 hours. This will
reduce the possibility of a malfunction in the cooling system from handling during transportation.
• Clean the interior surface with lukewarm water using a soft cloth.
• Install the handle on the door.
INSTALLATION OF YOUR APPLIANCE
• The appliance is designed for built-in, recessed or free standing installation.
• WARNING: Do not store or install the appliance outdoors.
• CAUTION: This beverage refrigerator is designed for storing and cooling beverages. Do not store perishable food,
medicine or other medical products.
• Place your appliance on a hard and level floor that is strong enough to support it when it is fully loaded.
• We do not recommend installing the appliance on carpet.
• To level your appliance, adjust the leveling legs at the bottom of the appliance if needed.
• For free standing installation, 5 inches (127mm) of space between the back and sides of the appliance is suggested,
which allows the proper air circulation to cool the compressor and condenser. Even for built-in installation, a
¼” (6.35mm) space is required on each side and at the top. The front air vent must never be covered or blocked in any
way.
• NOTE: DO NOT install the appliance near an oven or other heating source. Direct sunlight may affect the acrylic coating
and heat sources may increase electrical consumption. For best performance, do not install the appliance behind a
cabinet door or block the base grille.
• Avoid locating the appliance in area that may be exposed to excessive moisture.
• Plug in the appliance into an exclusive, grounded wall power outlet. Do not under any circumstances cut or remove
the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed
toward a qualified electrician or contact Whynter Customer Support.
7
Installation
BUILT-IN CABINET INSTRUCTIONS
These appliances are designed for both built-in or free standing installation. For built-in installation, ensure
proper service access and ventilation, allow at least ¼” space on each side and at the top.
CABINET OPENING DIMENSIONS (minimum)
BBR-148SB
Width
Depth
Height
ELECTRICAL CONNECTION
WARNING: Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is
damaged, have it replaced by a qualified electrician or contact Whynter Service Department
This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong. Have the wall
outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. The cord should
be secured behind the appliance and not left exposed or dangling to prevent accidental injury.
The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that
matches the rating label on the appliance. This provides the best performance and also prevents over-loading the
house wiring circuit that could cause a fire hazard from overheating. Never unplug the appliance by pulling the
power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or replace the power cord
immediately if it becomes frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage
along its length or at either end. When moving the appliance, be careful not to damage the power cord.
24”
23"
33"
EXTENSION CORD
Because of potential safety hazards, it is strongly recommended that you do not use an extension cord with this
appliance. However, if you must use an extension cord, it is absolutely necessary that it be a UL/CUL-Listed, 3-wire
grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of
the cord be 115 volts and at least 10 amperes.
INSTALLING STAINLESS STEEL HANDLE
This appliance includes stainless steel handle that are not required
to operate this appliance. To install the handle please follow the
below instructions:
1.
The gaskets are easily displaced by hand, no tools are necessary.
2.
Use a flat-head screwdriver to remove the two pre-installed
decorative plugs from the back of doors. Some beverage
refrigerators have no decorative plugs.
3.
Install the handle tightly as shown with two screws, lock washers
and flat washers provided. (DO NOT over tighten as this will cause
damage to the handle and stainless steel door frame).
4.
Replace the door gaskets to its original position.
Gasket
Flat Was her
Lock Washer
Screw
�
,
✓
►- � ,-
a
�
,
DoorFrame
-"'.
Handle
8
Installation
REVERSING THE DOOR SWING OF YOUR BEVERAGE REFRIGERATOR
Note: All parts removed must be saved for proper reinstallation of the door.
This appliance has the capability of the door opening from either the left or right side. The appliance is delivered
to you with the door opening from the left side. Should you desire to reverse the opening direction, please follow
the following reversal instructions.
1.Remove the front ventilation grille (2) and the adjustable ventilation grille (1) by unscrewing the screws
(3) & (4). (Figure 1)
2.Remove the bottom hinge plate (5) by unscrewing the four lock screws (6). Be careful to hold the glass door
firmly after removing the screws. (Figure 2)
3.Gently pull down to remove the glass door from the right top hinge and place it on a padded surface to avoid
the risk of damage, then remove the right top hinge (7). (Figures 3 & 4)
4.Unscrew and transfer the hinge pin of the bottom hinge plate (5) to the opposite side.
5.Pop out the cover caps on the upper left side corner of the inside cabinet and use them to
on the right hand side.
6.Screw the alternative left top hinge (9), included in the fittings, on the left hand side of cabinet. (Figure 4)
7.Relocate the door to the designated position. Then screw the bottom hinge assembly on the left designated
position and tighten it after the door is leveled. (Figure 2)
8.Reassemble the ventilation grilles.
cover the screw holes
9
Operation and Controls
It is recommended you install the appliance in a place where the ambient temperature is between 72º- 78ºF /
23º-26ºC. If the ambient temperature is above or below recommended temperatures, the performance of the
beverage refrigerator may be affected. For example, placing your appliance in extreme cold or hot conditions may
cause interior temperatures to fluctuate.
NOTE:
• When using the beverage refrigerator for the first time or restarting after being shut off for a long period of time,
there may be a few degree variance between the set temperature and the LED readout. This is normal due the
length of activation time. The unit should return to normal after running for a few hours. This unit will not raise
its internal temperature if the ambient temperature where the unit is located is lower than the set temperature.
CONTROL PANEL GUIDE
• POWER
To turn the appliance on/off, press and hold the power key for 5 seconds.
• UP
To increase (warm) the set temperature by 1°C or 1ºF.
• DOWN
To decrease (cool) the set temperature by 1°C or 1ºF.
• LIGHT
Used to turn the internal light on/off.
ºF/ºC SELECTOR
Select the temperature display setting in Fahrenheit or Celsius degree. To change the temperature from Fahrenheit
to Celsius or from Celsius to Fahrenheit, press and hold the LIGHT key for 5 seconds.
NOTE: If the appliance is unplugged, encounter power interruption, or turned off, you must wait 3 -5 minutes before
restarting the appliance. If attempted to restart before this time delay, the appliance may not start.
SETTING THE TEMPERATURE CONTROL
• During normal operation, the temperature display on the control panel shows the temperature inside the
appliance.
• When the unit is plugged in for the first time, the unit will power up automatically to the preset defaults. The
preset temperature is 40ºF (4ºC).
• You can press the UP and DOWN keys to control the internal temperature of the appliance.
• The temperature that you desire to set will increase 1ºC or 1ºF if you press the UP key once and will decrease
1ºC or 1ºF if you press the DOWN key once. The display flashes while you make the setting.
• After the temperature has been set, the display will flash four times before it shows the current internal
temperature of the particular temperature zone.
• To view the set temperature at any time, press the UP or DOWN key, the set temperature will temporarily flash in
the display for 5 seconds. Then the display shows the current internal temperature again.
10
Operation and Controls
TEMPERATURE MEMORY FUNCTION
In the event of a power interruption (power surge, breaker switch, etc.), the unit can remember the previous temperature
settings. When the power has restored, the temperature display will show the current cabinet temperature.
INTERIOR LIGHT
The interior light makes it easy to view your beverage labels and enhances the display of your collection. The light can be
turned on or off pressing the light button on the display.
CABINET SHELVES
NOTE:
Do not cover any part of the shelves with aluminum foil or any other material that will prevent adequate air circulation
within the cabinet.
This appliance is equipped with removable shelves. To prevent damage to the door gasket, make sure the door is
opened completely before pulling the shelves out.
ACTIVATED CARBON FILTER
The Whynter BBR-148SB is equipped with one activated carbon filter, which ensures optimum air quality within the
beverage cabinet. This filter counters and prevents any contaminants and odors from the ambient air affecting the taste
of the beverage stored.
Replace the active carbon filter once a year. If you are interested in purchasing an additional carbon filter, please
contact support@whynter.com for retail sales information.
To change the filter,
•Turn the filter cover 90° clockwise or counterclockwise and then remove the filter.
•Insert the new filter in the vertical position.
•Turn the filter cover 90° clockwise or counterclockwise until it click into position.
NORMAL SOUNDS
The unit is cooled by a compressor. The compressor pumps coolant through the cooling system, producing operating noise.
Even when the compressor cuts out, noises caused by changes in temperature and pressure are unavoidable. Operating noise
will be most audible immediately after the compressor comes on. It becomes quieter as the operating period continues.
The following noises are normal and occur from time to time:
•
Gurgling sound, caused by the refrigerant flowing through the appliance's coils,
•
Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on.
•
Cracking/popping sounds, resulting from the materials contraction and expansion due to temperature variations,
•
Fan operating sound, to circulate the air within the beverage cabinet.
•
Unusual noise is normally the result of improper installation.
•
Where the unit is installed in open-plan kitchen or in partition walls, the level of operating noise will be heard more
acutely. However, this is due to the surrounding architecture and not to the unit.
NOTE: An individual's perception of noise is directly linked to the environment in which the unit is located, as well the
specific type of models. Our appliances are in line with international standards for such appliance and in line with the
latest technical developments. Please remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
11
DEFROSTING AND VENTILATION
Your beverage refrigerator is designed with an automatic defrost system. During off-cycle, the evaporator behind the
rear wall of the unit defrosts automatically. Condensation is collected in the drain at the back of the unit and flows
through the drainage hole into the drip tray above the compressor. The heat is transferred from compressor and
evaporates any condensation that has collected in the drip tray. Part of the remaining water within the beverage re-
frigerator is collected for humidity purposes.
NOTE: Frost may accumulate on the evaporator if the unit is repeatedly opened in a high heat or high humidity location.
If this frost pattern does not clear within 24 hours, your unit will require manual defrosting.
Storage
BBR-148SB
Top Shelf : 42 cans
Mid Shelf : 42 cans
Lower Shelf : 42 cans
Bottom : 14 cans
42 + 42 + 42 + 14 = 140 cans
1
2
Care and Maintenance
CLEANING YOUR APPLIANCE
•
Turn off the power, unplug the appliance, and remove all contents from the appliance and store them in a suitable place.
•
Clean the inside, the door seal and the inside of the glass with a clean, damp cloth.
•
Never use detergents or other substances that emit odors.
•
Always keep the door closed when cleaning the outside of the appliance. Make sure no detergent odors penetrate into the
appliance.
•
Clean the side panels and door surfaces with a clean and soft cloth. If necessary, use a moist cloth. Alternatively, use a
microfiber cloth.
•
The humidity tray should be hand-washed with water and detergent. After cleaning, always make sure the tray is thoroughly
rinsed with clean water before replacing.
PREMISES POWER FAILURE
•
In the event of a power interruption, temperature settings automatically defaults to factory settings once power is restored.
•
Factory default temperature setting is 40°F. To set a different desired temperature,
refer to the "SETTING THE TEMPERATURE" and "
•
Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you
minimize the number of times the door is opened. If the power is going to be off for a longer period of time, yo
e proper
take th
steps to protect your contents.
°
C and °F SELECTOR" section on page 10.
u need to
VACATION TIME
•
Short vacations: Leave the appliance operating during vacations of less than two days.
•
Long vacations: If the appliance will not be used for an extended period, remove all items and turn off the appliance. Clean
and dry the interior thoroughly.
MOVING YOUR APPLIANCE
•
Remove all items inside the appliance.
•
Securely tape down ( we recommend using painter's tape ) all loose items ( shelves ) inside your appliance.
•
Turn the adjustable legs up to the base to avoid damage.
•
Tape ( we recommend using painter's tape ) the door shut.
•
Be sure the appliance stays secure in the upright position during transportation and protect the exterior of appliance with a
blanket, or similar item.
PREPARING FOR STORAGE
If the beverage refrigerator will not be used for a long time, or is to be moved to another place, it will be necessary to
defrost the unit and dry the interior.
1.
Disconnect the beverage refrigerator from the power supply by removing the power plug from the wall socket.
2.
Leave the door open to allow for air circulation and to prevent mold, mildew and unpleasant smells.
CAUTION: Store the unit out of the reach of children. If you have children, you may want to take additional
precautions such as removing the door to prevent a child from being trapped inside the beverage refrigerator.
NOTE:
•
If the beverage refrigerator is unplugged, encounter power lost, or turned off; you must wait 3 to 5 minutes before
restarting the beverage refrigerator.
•
When the beverage refrigerator is used for the first time or restarted after having been shut off for a long time, there could be
a few degrees variance between the temperature you select and the one indicated on the display. This is normal and it is due
to the length of the inactivation time.
•
The appliance should be located in the coolest area of the room, away from heat producing appliances, and out of any
direct sunlight.
•
Ensure that the appliance is adequately ventilated. Never obstruct the air vents.
•
Close the door tightly and do not open the appliance too frequently or for a long period of time.
•
Store the content in an organized way.
Do not over load the appliance to allow air to circulate.
•
1
3
Troubleshooting
Problem Possible Causes Solutions
The appliance does not operate
The appliance is not cold
enough
The appliance turns itself
on and off frequently
•
There is a power failure
•
The appliance is not plugged in
•
A fuse has blown or the circuit
breaker is tripped
The set temperature too high
•
•
The appliance is placed too close to
a heat source
•
The door is opened too often
•
The door is not closed completely
•
The door gasket does not seal
properly
•
The front bottom grille does not
have sufficient ventilation
•
The ambient room temperature
is too low or high
•
A large amo
been added to the appliance
•
The d
•
The door is not closed completely
•
The door gasket does not seal
properly
unt of contents has
oor is opened too often
•
Ensure the appliance is plugged in and
the power outlet has power
•
Replace the broken fuse or reset the
breaker
•
Adjust the set temperature
•
Keep the appliance away from sunshine
or other heat sources
•
Close the door tightly and do not open
the door too frequently or for a long
period of time
•
Ensure the door gasket is not loose. The
front bottom grille must be completely
unobstructed
•
Decrease or increase the ambient
room temperature
•
To minimize internal temperature fluc-
tuation, do not add large amount of
contents at once.
Close the door tightly and do not open
the door too frequently or for a long
period of time.
•
Ensure the door gasket is not loose.
The appliance makes too
much noise
The door does not
close properly
•
The noise may come from the flow of
the refrigerant and ex pansion of the
inside walls may cause popping and
crackling noises
•
Contraction and expansion of the
inside walls may cause popping and
crackling noises
•
The appliance is not level
•
The appliance is not level
•
The door was reversed and not
properly installed
•
The shelves are out of position
•It is normal that as each cooling cycle
ends, you may hear rattling or
gurgling sounds caused by the flow of
refrigerant in the appliance. The high
efficiency compressor may make a
pulsating or high pitched sound.
•Some popping or cracking noises are
normal. They are caused by expansion
and contraction of the inside walls due
to temperature changes.
•Make sure the unit is on a hard and
level surface. Do not place the
appliance on carpet.
•See Operating Noises.
Make sure the appliance is on a hard and
•
level surface. Avoid placing the
appliance on a carpeted or soft surface
•
Correctly install the shelves
14
Troubleshooting
Problem Possible Causes Solutions
Display flashing
Display “E1”, “E2”.
“E5”, “E6”, “EU”, “LO”, or “HI”
The icon “--” is lit up and
flashing in the temperature
display
•Set temperature has not
been reached
•E1 E2 - air temperature sensor error
•E5 E6 - defrost sensor error
•EU - display error
•LO - low temperature alarm
•HI - high temperature alarm
•The display temperature is out
of the range
•It is normal for the display to flash until
the unit reaches the set temperature.
Please note that the unit may take unto
24 hours to reach the set temperature if
the cabinet is full.
•Contact Whynter Customer Support
•Only temperatures within the range
16 - 99°F/-9 - 37°C the appliance can
display will be shown. If the tempera-
ture is not within this range, the icon “--”
will be displayed instead. That is nor-
mal.
15
ONE YEAR LIMITED WARRANTY
This WHYNTER Beverage Refrigerator is warranted, to the original owner within the 48 continental states, for one year
from the date of purchase against defects in material and workmanship under normal use and service. When making a
warranty claim, please have the original bill or invoice of purchase with purchase date available. Should your WHYNTER
Beverage Refrigerator prove defective within one year from the date of purchase, return the defective part or unit,
freight prepaid (within two months of purchase; after two months to one year, customer will be responsible for freight
cost to Whynter’s service department), along with an explanation of the claim to Whynter LLC. A return authorization
number issued by Whynter is required for all warranty claims and returns. Please package the WHYNTER Beverage
Refrigerator carefully in its original packaging material to avoid damage in transit. The original box and packaging
material should be retained, as Whynter is not responsible for the cost of replacement packaging. Under this warranty,
Whynter will repair or replace any parts found defective at our discretion. This warranty is not transferable. After the
expiration of the warranty, the cost of labor and parts will be the responsibility of the original owner of the unit.
THIS WARRANTY DOES NOT COVER:
• Acts of God, such as fire, flood, hurricanes, earthquakes and tornadoes.
• Improper power supply such as power surge, low voltage, defective household wiring or inadequate
fuses.
• Use in commercial or industrial applications.
• Damage, accidental or otherwise, to the WHYNTER Beverage Refrigerator while in the possession
of a consumer not caused by a defect in material or workmanship
• Damage caused by consumer misuse, tampering, or failure to follow the care and special handling
provisions in the instructions.
• Damage to the finish of the case, or other appearance parts caused by wear.
• Damage caused by repairs or alterations to the product by anyone other than authorized by the
manufacturer.
• Removal, Replacement Packaging, Freight and Insurance cost for the warranty service.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER
THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PRO-VIDED HEREIN. CLAIMS BASED ON
IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTA-BILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PE-RIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. WHYNTER SHALL
NOT BE LIABLE FOR CON-SEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL
EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME
STATES AND PROVINCES DO NOT AL-LOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY
NOT APPLY TO YOU. THIS WRIT-TEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE.
Please retain the original proof of purchase in order to obtain warranty services.
Warranty begins from the original date of purchase.
To obtain service or information, contact
Whynter LLC via email at
support@whynter.com or call
866-WHYNTER.
Product contents and specifications may change without notice.
Copyright © 2021 Whynter LLC
WWW.WHYNTER.COM
Loading...