White Outdoor 769-01923A User Manual
Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
Two-Stage Snow Thrower — H-Style
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any uniiproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
PRINTED IN U.S.A
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
FORM NO. 769-01923A
06/21/2006
This Operator’s Manual is an important part of your new snow thrower. It will help you assemble,
DEALER LOCATOR PHONE NUMBER:
800-949-4483
MTD LLC
P. O. BOX
361131
CLEVELAND,OH
44136
www.whiteoutdoor.com
prepare and maintain the unit for best performance. Please read and understand what it says.
Table of Contents
Safety Labels .........................................
Safe Operation Practices ......................Page 4
Setting Up Your Snow Thrower .............Page 6
Operating Your Snow Thrower ..............Page 8
Adjusting Your Snow Thrower .............Page12
Page 3
Finding and Recording Model Number
BEFORE YOU START ASSEMBLING
STOP
Please locate the model plate on the equipment and copy the
information to the sample model plate provided to the right.
You can locate the model plate by standing at the operating
position and looking down at the rear of the snow thrower. This
information will be necessary to use the web site or obtain
assistance from your White Outdoor dealer.
YOUR NEW EQUIPMENT
Maintaining Your Snow Thrower ........Page 14
Off-Season Storage .............................Page 18
Troubleshooting ...................................Page 19
Illustrated Parts List ............................Page 20
Warranty .........................................Back Cover
Customer Support
Please do
purchased, without first contacting Customer Support.
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this unit,
you can seek help from the experts. Choose from the options below:
1. Visit
2. Phone our Dealer Locator line at (800)-949-4483 to find
www.whiteoutdoor.com. Click on the Customer Support
menu option.
your local White Outdoor dealer.
NOT
return the unit to the retailer from which it was
3. The engine manufacturer is responsible for all enginerelated issues with regards to performance, power-rating,
specifications, warranty and service. Please refer to the
engine manufacturer’s Owner’s/Operator’s Manual, packed
separately with your unit, for more information.
2
#HUTE#LEANOUT4OOL
+%%0!7!9&2/-2/4!4).')-0%,,%2
!.$!5'%2#/.4!#47)4()-0%,,%2/2
!5'%2#!.!-054!4%(!.$3!.$&%%4
53%#,%!./544//,4/5.#,/'
$)3#(!2'%#(54%
$)3%.'!'%#,54#(,%6%2334/0%.').%
!.$2%-!)."%().$(!.$,%35.4),!,,
-/6).'0!243(!6%34/00%$"%&/2%
5.#,/'').'/23%26)#).'-!#().%
4/!6/)$4(2/7./"*%#43).*52)%3
.%6%2$)2%#4$)3#(!2'%!4"934!.$%23
53%%842!#!54)/.7(%./0%2!4).'/.
'2!6%,352&!#%3
2%!$/0%2!4/2g3-!.5!,
$!.'%2
#,%!. /54 4//,
$!.'%2
!6/)$).*529&2/2/4!4).'!5'%2
+%%0(!.$3&%%4
!.$#,/4().'!7!9
$!.'%2
.%6%2054(!.$).#(54%#/.4!#47)4(
2/4!4).'0!243#!.!-054!4%&).'%23
!.$(!.$3
3( 54/&&%.') .%!.$ 7!) 45.4) ,!,,
-/6).' 0!243(!6 %34/ 00%$"%&/2%
5.#,/'').'
53%#,%!./544//,/27//$%.
34)#+4/
5.#,/'$)3#(!2'%#(54%
1
Safety
Labels
WARNING
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
manual before attempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
HEED ITS WARNING!
A chute clean-out tool is fastened to the top of the
auger housing with a mounting clip. The tool is designed
to clear a chute assembly of ice and snow.
This item is fastened with a cable tie at the factory. Cut
the cable tie before operating the snow thrower.
3
WARNING: Never use your
hands to clear a clogged chute
assembly. Shut off engine and
remain behind handles until
all moving parts have stopped
before using the clean-out tool
to clear the chute assembly.
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
2
Safe
Operation
Practices
WARNING
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
manual before attempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
HEED ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
Training
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them quickly.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the operation instructions and safety rules in
this manual and should be trained and supervised by a
parent.
4. Never allow adults to operate this machine without proper
instruction.
5. Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially
when operating in reverse.
1. Thoroughly inspect the area where the equipment is to be
used. Remove all doormats, newspapers, sleds, boards,
wires and other foreign objects, which could be tripped over
or thrown by the auger/impeller.
2. Always wear safety glasses or eye shields during operation
and while performing an adjustment or repair to protect your
eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
3. Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other
loose clothing, which could become entangled in moving
parts. Wear footwear which will improve footing on slippery
surfaces.
4. Use a grounded three-wire extension cord and receptacle
for all units with electric start engines.
5. Adjust collector housing height to clear gravel or crushed
rock surfaces.
6. Disengage all control levers before starting the engine.
7. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
8. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
9. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive. Serious personal injury can
occur when gasoline is spilled on yourself or your clothes,
which can ignite. Wash your skin and change clothes
immediately.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is hot
or running.
e. Allow engine to cool at least two minutes before refuel
ing.
f. Never over fill fuel tank. Fill tank to no more than ½ inch
below bottom of filler neck to provide space for fuel
expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and equip
ment. Move machine to another area. Wait 5 minutes
before starting the engine.
i. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light (e.g. furnace,
water heater, space heater, clothes dr yer etc.).
j. Allow machine to cool at least 5 minutes before storing.
Preparation
-
-
4
Operation
1. Do not put hands or feet near rotating par ts, in the auger/im-
peller housing or chute assembly. Contact with the rotating
parts can amputate hands and feet.
2. The auger/ impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
3. The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
4. Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless and
deadly gas.
6. Do not operate machine while under the influence of alcohol
or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operat
ing on slopes.
10. Plan your snow-throwing pattern to avoid discharge towards
windows, walls, cars etc. Thus, avoiding possible property
damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
14. Disengage power to the auger/impeller when transporting
or not in use.
15. Never operate machine at high transpor t speeds on slippery
surfaces. Look down and behind and use care when
backing up.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
17. Disengage all control levers and stop engine before you
leave the operating position ( behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments, or
inspections.
18. Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the
discharge opening. Do not unclog chute assembly while en-
gine is running. Shut off engine and remain behind handles
until all moving parts have stopped before unclogging.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. If situations occur which are not covered in this manual,
use care and good judgment. Contact your Whi te Outdoor
dealer or call ( 800 ) 949-4483 for the name of your nearest
servicing dealer.
Maintenance & Storage
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and adjust-
ment sections of this manual.
2. Before cleaning, repairing, or inspecting machine disen
gage all control levers and stop the engine. Wait until the
auger/impeller come to a complete stop. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) par ts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper per formance and compromise safety !”
6. Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator’s manual for instructions.
7. Maintain or replace safety and instruction labels, as neces
sary.
8. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper instructions
on off-season storage.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Notice regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modification (EM) and Three Way Catalyst (TWC) if so equipped.
Your Responsibility
Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual
and on the machine.
-
2
Safe
Operation
Practices
WARNING
-
This symbol points
out important safety
instructions, which if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this manual before attempting to
operate this machine.
Failure to comply with
these instructions may
result in personal injury.
When you see this
symbol.
HEED IT’S WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
5
5
Setting Up
Your Snow
Thrower
NOTE: Reference to right
and left side of the machine
are observed from the
operating position.
NOTE: This Operator’s
Manual covers several
models. Snow thrower
features vary by model.
Not all features discussed
and/or pictured in this
manual are applicable to all
snow thrower models.
1
1. Observe the lower rear area of the snow thrower to
be sure both cables are aligned with roller guides
before pivoting the handle upward.
2. Secure the handle by tightening the plastic wing
knob located on both the left and right sides of the
handle. Remove and discard any rubber bands, if
present. They are for packaging purposes only.
3. Position the chute assembly over the base.
4. Close the flange keepers to secure the chute
assembly to the chute base. The flange keepers will
click into place when properly secure.
NOTE: If the flange keepers will not easily click into
place, use the palm of your hand to apply swift, firm
pressure to the back of each.
2
3
NOTE: Two replacement
auger shear pins and bow
tie cotter pins are provided
for your convenience. Store
in a safe place until
needed. Refer to “Augers”
in the Maintenance Section
of this manual for more
information.
4
6
5. Remove the flat washer and hairpin clip from the end
of the chute directional control.
Insert the end of the chute directional control into the
lower bracket and secure with the flat washer and hairpin clip just removed. If necessary, the lower bracket
can be adjusted. Refer to Chute Bracket Adjustment.
on Page 13.
Adjustments
Auger Control
IMPORTANT: Prior to operating your snow thrower, refer
to Auger Control Test on page 11. Read and follow all
instructions carefully and perform all adjustments to verify
your snow thrower is operating safely and properly.
Skid Shoes
5
5
Setting Up
Your Snow
Thrower
IMPORTANT: It is not recommended that you operate
this snow thrower on gravel as loose gravel can be easily
picked up and thrown by the auger causing personal
injury or damage to the snow thrower.
The snow thrower skid shoes are adjusted upward at the
factory for shipping purposes. Adjust them downward, if
desired, prior to operating the snow thrower. Refer to Skid
Shoes on page 12.
NOTE: If you choose to operate the snow thrower on
a gravel surface, keep the skid shoes in position for
maximum clearance between the ground and the shave
plate.
Tire Pressure
Before operating, check tire pressure and reduce pressure in both tires to between 15 psi and 20 psi.
NOTE: If the tire pressure is not equal in both tires, the
unit may not travel in a straight path and the shave plate
may wear unevenly.
IMPORTANT
Prior to operating your
snow thrower, refer
to Auger Control Test
on page 11. Read and
follow all instructions
carefully and perform
all adjustments to verify
your snow thrower is
operating safely and
properly.
7
4
Engine Controls
Recoil Starter
Handle
Electric Starter Outlet
Primer
Ignition
Key
Choke
Control
Throttle
Control
Drive Control
Oil Fill
Chute Assembly
Gas Cap
Shift Lever
Auger Control
Chute Directional Control
Electric Start Button
Clean Out
Tool
Augers
Skid Shoe
34/0
Operating
Your Snow
Thrower
WARNING
Read, understand,
and follow all instructions and warnings
on the machine and
in this manual before
operating.
Know Your Snow Thrower
Figure 1
Use extreme care
when handling
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
Now that you have set up your snow thrower for
operation, get acquainted with its controls and
features. These are described below and illustrated
this page. This knowledge will allow you to use your
new equipment to its fullest potential.
NOTE: For detailed starting instructions and more
information on all engine controls, refer to the Tecumseh
Engines manual packed separately and Starting The
Engine on page 10 of this manual.
Shift Lever
The shift lever is located on the right
side of the handle panel. Place the
shift lever into any of eight positions
to control the direction of travel and
ground speed.
Forward
There are six forward (F) speeds. Position one (1) is the slowest and position
six (6) is the fastest.
Reverse
There are two reverse (R) speeds.
One (1) is the slower and two (2) is the
faster.
Choke Control
The choke control is found on the rear of the engine and
is activated by rotating the knob clockwise. Activating the
choke control closes the choke plate on the carburetor
and aids in starting the engine.
Throttle Control
The throttle control is located on the
engine. It regulates the speed of the
engine and will shut off the engine when
pushed down completely.
Primer
Depressing the primer forces fuel directly
into the engine’s carburetor to aid in
cold-weather starting.
Oil Fill
Engine oil level can be checked and oil
added through the oil fill.
8
Auger Control
!5'%2
#/.42/,
'/
$2)6%
#/.42/,
'/
#(54%$)2%#4)/.!,#/.42/,
$)3#(!2'%
,%&4
$)3#(!2'%
2)'(4
!$*534!",%
#(54%4),4
Chute Directional Control
4
Operating
Your Snow
Thrower
The auger control is located on the left handle. Squeeze
the control grip against the handle to engage the augers
and start snow throwing action. Release to stop.
Drive Control / Auger Clutch Lock
The drive control is located on the right handle. Squeeze
the control grip against the handle to engage the wheel
drive. Release to stop.
The drive control also locks the auger control so that
you can operate the chute directional control without
interrupting the snow throwing process. If the auger
control is engaged simultaneously with the drive control,
the operator can release the auger control (on the left
handle) and the augers will remain engaged. Release
both controls to stop the augers and wheel drive.
IMPORTANT: Always release the drive control before
changing speeds.
Ignition Key
The ignition key is a safety devise. It must be fully
inserted in order for the engine to start. Remove the
ignition key when the snow thrower is not in use.
NOTE: Do not turn the ignition key in an attempt to start
the engine. Doing so may cause it to break.
Recoil Starter Handle
This handle is used to manually start the engine.
Electric Starter Button
Pressing the electric starter button engages the engine’s
electric starter when plugged into a 120V power source.
The chute directional control is located on left side of the
snow thrower.
To change the direction in which snow is thrown, turn
chute directional control as follows:
• Crank clockwise to discharge to the left.
• Crank counterclockwise to discharge to the right.
Clean-Out Tool
WARNING: Never use your hands
to clear a clogged chute assembly. Shut off engine and remain
behind handles until all moving
parts have stopped before
unclogging.
The chute clean-out tool is fastened to the top of the
auger housing with a mounting clip. The tool is designed
to clear a clogged chute assembly.
NOTE: This item is fastened with a cable tie to the rear
of the auger housing at the factory. Cut the cable tie
before operating the snow thrower.
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces.
Electric Starter Outlet
Requires the use of a three-prong outdoor extension cord
(included) and a 120V power source/wall outlet.
Augers
When engaged, the augers rotate and draw snow into the
auger housing.
Chute Assembly
Snow drawn into the auger housing is discharged out the
chute assembly.
Gas Cap
Unthread the gas cap to add gasoline to the fuel tank.
WARNING
The operation of
any snow thrower
can result in foreign
objects being thrown
into the eyes, which
can damage your
eyes severely. Always
wear safety glasses
while operating the
snow thrower, or while
performing any adjustments or repairs on it.
Be sure no one other
than the operator is
standing near the snow
thrower while starting
engine or operating
snow thrower. Never
run engine indoors or
in enclosed, poorly
ventilated areas. Engine exhaust contains
carbon monoxide, an
odorless and deadly
gas. Keep hands, feet,
hair and loose clothing
away from any moving
parts on engine and
snow thrower.
9
Loading...