Whirlpool WFW9351YW, YMHWE251YG, YWFW9351YW, YWFW9351YL, YWFW9151YW Installation Instructions
...
WASHER
INSTRUCTIONS
INSTALLATION
INSTRUCTIONS
Table of Contents
WASHER SAFETY .........................................................1
INSTALLATION REQUIREMENTS ................................ 2
Tools and Parts ................................................................ 2
Alternative Parts .............................................................. 2
Location Requirements ..................................................3
Drain System ...................................................................4
Electrical Requirements .................................................5
INSTALLATION INSTRUCTIONS .................................. 5
Connect Drain Hose ........................................................ 6
Connect Inlet Hoses ........................................................7
Level Washer ...................................................................8
Complete Installation Checklist ..................................... 9
INSTALLATION NOTES
Date of purchase: _________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
D’INSTALLATION
DE LA LAVEUSE
Table des matières
SÉCURITÉ DE LA LAVEUSE ......................................10
EXIGENCES D’INSTALLATION ..................................10
Outillage et pièces ........................................................10
Autres pièces .................................................................10
Exigences d’emplacement ...........................................11
Système de vidange ...................................................... 13
Spécications électriques ............................................ 13
INSTRUCTIONS D’INSTALLATION ............................ 14
Raccordement du tuyau de vidange............................15
Raccordement des tuyaux d’arrivée d’eau .................16
Établissement de l’aplomb de la laveuse .................... 17
Liste de vérication pour l’achèvement
de l’installation ..............................................................19
NOTES SUR L’INSTALLATION
Date d’achat : ____________________________________
Date d’installation : _______________________________
Installateur : _____________________________________
Numéro de modèle : _______________________________
Numéro de série : _________________________________
W10408696B
W10409178B - SP
WASHER SAFETY
INSTALLATION REQUIREMENTS
Tools and Parts
Gather required tools and parts before starting installation.
Tools needed:
Parts needed: (Not supplied with washer)
Inlet hoses (2) with
washers (4)
Adjustable or open end
wrenches 1⁄2" (13 mm) and
9
⁄16" (14 mm)
4" min
(102 mm)
Wood block
Pliers that open to 19⁄16"
(39.5 mm)
Level
Ruler or measuring tape
Parts supplied:
NOTE: All parts supplied for installation are in the washer
basket.
Beaded tie strap
Drain hose form and hose
clamp
Drain hose
Transport bolt hole
plugs (Quantity will vary,
depending on model.)
Optional tools:
Alternative Inlet Hoses:
(may be required for some installations, not supplied
with washer)
n
8212656RP 10 ft (3.0 m) Inlet hose, Black EPDM (2 pack)
n
8212641RP 5 ft (1.5 m) Inlet hose, Black EPDM (2 pack)
n
8212546RP 4 ft (1.2 m) Inlet hose, Black EPDM (2 pack)
n
8212545RP 5 ft (1.5 m) Inlet hose, Red and Blue EPDM
(2 pack)
n
8212487RP 5 ft (1.5 m) Nylon braided inlet hose (2 pack)
n
8212638RP 6 ft (1.8 m) Nylon braided inlet hose, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
n
8212637RP 6 ft (1.8 m) Inlet hose, Black EPDM, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
Available Accessories:
An optional matching pedestal is available for your washer.
Please contact your retailer for ordering information, or see
the Assistance or Service page on the back of your Use and
Care Guide.
Alternative parts
(Not supplied with washer)
Your installation may require additional parts. To order, please
refer to toll-free numbers on the back page of your Use and
Care Guide.
If you have: You will need:
Laundry tub or Sump pump system
standpipe taller than (if not already available)
96" (2.4 m)
Overhead sewer Standard 20 gal. (76 L) 30" (762 mm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm)
diameter Standpipe Adapter
Part Number 3363920
Connect Kit Part Number 285835
Floor drain system Siphon Break Part Number 285834;
additional Drain Hose,
Part Number 8318155; and Connector
Kit, Part Number 285835
Flashlight Bucket
2
Drain hose too short Extension Drain Hose
Part Number 285863
Water faucets beyond 2 longer water ll hoses;
reach of ll hoses 6 ft (1.8 m) Part Number 76314
10 ft (3.0 m) Part Number 350008
LOCATION REQUIREMENTS
Proper installation is your responsibility.
You will need:
n
A water heater set to 120° F (49° C).
n
A grounded electrical outlet located within 6 ft (1.8 m) of
power cord on back of washer.
n
Hot and cold water faucets located within 4 ft (1.2 m) of hot
and cold water ll valves on washer, and water pressure of
20-100 psi (137.9-689.6 kPa).
n
A level oor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet or surfaces with foam backing is
not recommended.
n
Floor must support washer’s total weight (with water and load)
of 400 lbs (180 kgs).
IMPORTANT: Do not install, store, or operate washer where
it will be exposed to weather or in temperatures below 32° F
(0° C). Water remaining in washer after use may cause damage
in low temperatures. See “Washer Care” in Washer Use and Care
Guide for winterizing information.
1
50
/4"
(1276 mm)
27"
(686 mm)
36"
(914 mm)
301/2"
(775 mm)
All dimensions show recommended spacing allowed, except for
closet door ventilation openings which are the minimum required.
For each arrangement, consider allowing more space for ease of
installation and servicing, and spacing for companion appliances
and clearances for walls, doors, and oor moldings.
Space must be large enough to allow door to fully open.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed, top
and bottom air openings in door are required.
Recessed area or closet installation
(stacked washer and dryer):
12"
(305 mm)
3"
1
/4"
5
(133 mm)
1"
(25 mm)
(76 mm)
72"
(1829 mm)
3"
(76 mm)
1"
(25 mm)
2
48 in.
(310 cm2)
2
24 in.
(155 cm2)
Recessed area or closet installation (washer only):
3"
(76 mm)
3"
(76 mm)
2
48 in.
(310 cm2)
2
24 in.
(155 cm2)
4"
(102 mm)
48" min.
(1220 mm)
1"
(25 mm)
1"
(25 mm)
Recessed or closet installation (washer on pedestal):
" min.
38" min.
24
(610 mm)
(965 mm)
Custom under counter installation:
1"
(25 mm)
1"
(50 mm)
36" min.
(914 mm)
2"
4"
(102 mm)
1"
(25 mm)
1"
(25 mm)
3
41/2"
(113 mm)
Custom cabinet installation: Wall standpipe drain system
7"
(178 mm)
9"
(229 mm)
4"
(102 mm)
1"
(25 mm)
1"
(25 mm)
DRAIN SYSTEM
Drain system can be installed using a oor drain, wall standpipe,
oor standpipe, or laundry tub. Select method you need.
IMPORTANT: To avoid siphoning, only 4
hose should be inside standpipe. Always secure drain hose with
beaded tie strap.
Floor standpipe drain system
41/2"
(113 mm)
30"
(762 mm)
1
/2" (113 mm) of drain
41/2"
(113 mm)
See requirements for oor standpipe drain system.
Laundry tub drain system
30"
30"
(762 mm)
(762 mm)
Minimum capacity: 20 gal. (76 L). Top of laundry tub must
be at least 30" (762 mm) above oor; install no higher than
96" (2.4 m) from bottom of washer.
Floor drain system
30"
28"
(762 mm)
(710 mm)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm)
diameter to 1" (25 mm) diameter Standpipe Adapter Kit is
available (Part Number 3363920). Top of standpipe must be
at least 30" (762 mm) high; install no higher than 96" (2.4 m)
from bottom of washer. If you have an overhead sewer and
need to pump higher than 96 inches, a sump pump and
associated hardware are needed. See “Alternative Parts”.
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. See “Alternative Parts”. Minimum siphon
break height: 28" (710 mm) from bottom of washer. (Additional
hoses may be needed.)
4
ELECTRICAL REQUIREMENTS
n
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is recommended that a separate circuit
breaker serving only this appliance be provided.
n
This washer is equipped with a power supply cord having
a 3 prong grounding plug.
n
To minimize possible shock hazard, the cord must be plugged
into a mating, 3 prong, grounding-type outlet, grounded in
accordance with local codes and ordinances. If a mating outlet
is not available, it is the personal responsibility and obligation
of the customer to have the properly grounded outlet installed
by a qualied electrician.
n
If codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine that
the ground path is adequate.
n
Do not ground to a gas pipe.
n
Check with a qualied electrician if you are not sure the
washer is properly grounded.
n
Do not have a fuse in the neutral or ground circuit.
INSTALLATION
INSTRUCTIONS
NOTE: To avoid oor damage, set washer onto cardboard
before moving it.
1. Move washer
48"
(1.2 m)
It is necessary to remove all shipping materials for proper
operation and to avoid excessive noise from washer.
Move washer to within 36" (914 mm) of its nal location. It must
be in a fully upright position.
2. Locate transport bolts
Locate all transport bolts on rear of washer (quantity may vary,
depending on model).
5
3. Remove transport bolts from
washer
Loosen bolts with a 13 mm (1/2") wrench.
Slide each bolt and spacer to center of hole. Pull bolts and
plastic spacers from back of washer. Save transport bolts
and spacers. Contact a qualied servicer if washer is to be
transported.
4. Cover bolt holes with transport
bolt hole plugs
6. Place power cord over top
Gently place power cord over top of washer to allow free
access to back of washer.
CONNECT DRAIN HOSE
7. Attach drain hose to drain port
Close bolt holes on cabinet back with transport bolt hole plugs
included with washer parts.
5. Remove power cord
Pull power cord through opening in rear panel and close
holes (2) with attached white plastic cap.
NOTE: If washer is transported at a later date, call a certied
technician to properly set up washer for relocation, to avoid
suspension and structural damage.
6
Squeeze hose clamp tabs with pliers and slide over end of
drain hose. Slide drain hose onto washer elbow connector
and secure with clamp.
For a laundry tub or standpipe drain, go to step 8.
You may need additional parts with separate directions.
See Floor drain system under “Alternative Parts”.
Loading...