THANK YOU for purchasing this high-quality product. Register your new range at www.whirlpool.com. In Canada, register your range
at www.whirlpool.ca.
For future reference, please make a note of your product model and serial numbers. These can be located on the oven frame behind
the top right side of the oven door.
Model Number__________________________________________ Serial Number__________________________________________
Para una versión de estas instrucciones en español, visite www.whirlpool.com.
Deberá tener a mano el número de modelo y de serie, que están ubicados en el marco del horno, detrás del lado derecho
superior de la puerta del horno.
Table of Contents
RANGE SAFETY .............................................................................2
The Anti-Tip Bracket ....................................................................2
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without
having the anti-tip bracket fastened down properly.
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
follow
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
Anti-Tip
Bracket
Range Foot
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
■ WARNING: TO REDUCE THE RISK OF TIPPING OF
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR OR WALL, AND
SLIDE RANGE BACK SO REAR RANGE FOOT IS
UNDER ANTI-TIP BRACKET.
■
CAUTION:
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be
seriously injured.
■ Proper Installation – Be sure the range is properly installed
and grounded by a qualified technician.
■ Never Use the Range for Warming or Heating the Room.
■ Do Not Leave Children Alone – Children should not be left
alone or unattended in area where the range is in use.
They should never be allowed to sit or stand on any part of
the range.
Wear Proper Apparel – Loose-fitting or hanging garments
■
should never be worn while using the range.
User Servicing – Do not repair or replace any part of the
■
range unless specifically recommended in the manual. All
other servicing should be referred to a qualified technician.
Storage in or on the Range – Flammable materials should
■
not be stored in an oven or near surface units.
Do Not Use Water on Grease Fires – Smother fire or flame
■
or use dry chemical or foam-type extinguisher.
■ Use Only Dry Potholders – Moist or damp potholders on
hot surfaces may result in burns from steam. Do not let
potholder touch hot heating elements. Do not use a towel
or other bulky cloth.
DO NOT TOUCH SURFACE UNITS OR AREAS NEAR
■
UNITS – Surface units may be hot even though they are
dark in color. Areas near surface units may become hot
enough to cause burns. During and after use, do not touch,
or let clothing or other flammable materials contact surface
units or areas near units until they have had sufficient time
to cool. Among those areas are the cooktop and surfaces
facing the cooktop.
■ Use Proper Pan Size – The range is equipped with one or
more surface units of different size. Select utensils having
flat bottoms large enough to cover the surface unit heating
element. The use of undersized utensils will expose a
portion of the heating element to direct contact and may
result in ignition of clothing. Proper relationship of utensil to
burner will also improve efficiency.
■ Never Leave Surface Units Unattended at High Heat
Settings – Boilover causes smoking and greasy spillovers
that may ignite.
■ Make Sure Reflector Pans or Drip Bowls Are in Place –
Absence of these pans or bowls during cooking may
subject wiring or components underneath to damage.
Do not store items of interest to children in
Protective Liners – Do not use aluminum foil to line surface
■
unit drip bowls or oven bottoms, except as suggested in
the manual. Improper installation of these liners may result
in a risk of electric shock, or fire.
Glazed Cooking Utensils – Only certain types of glass,
■
glass/ceramic, ceramic, earthenware, or other glazed
utensils are suitable for range-top service without breaking
due to the sudden change in temperature.
Utensil Handles Should Be Turned Inward and Not Extend
■
Over Adjacent Surface Units – To reduce the risk of burns,
ignition of flammable materials, and spillage due to
unintentional contact with the utensil, the handle of a
utensil should be positioned so that it is turned inward, and
does not extend over adjacent surface units.
■ Do Not Soak Removable Heating Elements – Heating
elements should never be immersed in water.
Do Not Cook on Broken Cooktop – If cooktop should
■
break, cleaning solutions and spillovers may penetrate the
broken cooktop and create a risk of electric shock. Contact
a qualified technician immediately.
■ Clean Cooktop With Caution – If a wet sponge or cloth is
used to wipe spills on a hot cooking area, be careful to
avoid steam burn. Some cleaners can produce noxious
fumes if applied to a hot surface.
■ Use Care When Opening Door – Let hot air or steam
escape before removing or replacing food.
■ Do Not Heat Unopened Food Containers – Build-up of
pressure may cause container to burst and result in injury.
■ Keep Oven Vent Ducts Unobstructed.
Placement of Oven Racks – Always place oven racks in
■
desired location while oven is
cool. If rack must be moved
while oven is hot, do not let potholder contact hot heating
element in oven.
DO NOT TOUCH HEATING ELEMENTS OR INTERIOR
■
SURFACES OF OVEN – Heating elements may be hot even
though they are dark in color. Interior surfaces of an oven
become hot enough to cause burns. During and after use,
do not touch, or let clothing or other flammable materials
contact heating elements or interior surfaces of oven until
they have had sufficient time to cool. Other surfaces of the
appliance may become hot enough to cause burns – among
these surfaces are oven vent openings and surfaces near
these openings, oven doors, and windows of oven doors.
For self-cleaning ranges –
■ Do Not Clean Door Gasket – The door gasket is essential
for a good seal. Care should be taken not to rub, damage,
or move the gasket.
■ Do Not Use Oven Cleaners – No commercial oven cleaner
or oven liner protective coating of any kind should be used
in or around any part of the oven.
■ Clean Only Parts Listed in Manual.
■ Before Self-Cleaning the Oven – Remove broiler pan and
other utensils.
For units with ventilating hood –
Clean Ventilating Hoods Frequently – Grease should not
■
be allowed to accumulate on hood or filter.
■ When flambeing foods under the hood, turn the fan on.
SAVE THESE INSTRUCTIONS
3
FEATURE GUIDE
This manual covers several models. Your model may have some or all of the items listed. Refer to this manual or Frequently Asked
Questions (FAQs) section of our website at www.whirlpool.com for more detailed instructions. In Canada, reference the Customer
Service section at www.whirlpool.ca.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
KEYPADFEATUREINSTRUCTIONS
CLOCKClock
OVEN LIGHTOven cavity
light
This clock can use a 12- or 24-hour cycle. See “Electronic Oven Controls” section.
1. Press SETTINGS once, then wait 5 seconds.
2. Press START to change the time.
3. Press “3” for AM or “6” for PM.
4. Press the number keypads to set the time of day.
5. Press START.
While the oven door is closed, press the OVEN LIGHT keypad to turn the light on and off. The
oven light will come on when the oven door is opened.
TIMER
(Set/Off)
STARTCooking start
CANCELRange function
BAKEBaking and
Oven timer
roasting
The Timer can be set in hours or minutes up to 9 hours and 59 minutes.
1. Press TIMER.
2. Press the number keypads to set the length of time in hr-hr-min-min. Leading zeroes do
not have to be entered. For example, for 2 minutes, enter “2.”
3. Press TIMER or START to begin the countdown. If enabled, end-of-cycle tones will sound
at end of countdown.
4. Press TIMER twice to cancel the Timer and return to the Time of Day. Do not press the
Cancel keypad because the oven will turn off.
5. If the Timer is running, but not in the display, press TIMER to display the countdown for
5 seconds.
The Start pad begins any oven function. If Start is not pressed within 30 seconds after
pressing a keypad, the function is canceled and the time of day is displayed.
The Cancel keypad stops any oven function except the Clock, Timer, Control Lock and
Warming Drawer.
1. Press BAKE.
2. Press the number keypads to set a temperature other than 350°F (175°C) in 5° increments
between 170°F and 500°F (75°C and 260°C).
3. Press START.
4. To change the temperature, repeat steps 1 and 2. Press START or wait 5 seconds for the
change to take effect.
5. Press CANCEL when finished.
4
KEYPADFEATUREINSTRUCTIONS
FROZEN BAKEPrepackaged
BROILBroiling
CONVECTConvection
KEEP WARMHold warm
START TIMEDelayed start
COOK TIMETimed
RAPID
PREHEAT
WARM ZONE
ON/OFF
food
cooking
cooking
Rapid oven
preheating
Warming zone
1. Position the food on a flat rack in the oven on rack position 4. See the “Positioning Racks
and Bakeware” section.
NOTE: Cook only 1 package of frozen food at a time when using FrozenBake™ Technology.
2. Press FROZEN BAKE.
3. Press FROZEN BAKE until the desired food option is displayed.
4. Press the number keypads to set the temperature as recommended on the food packaging.
5. Press COOK TIME.
6. Press the number keypads to set the maximum cook time as recommended on the food
packaging.
7. Press START. The range will calculate the best cook time based on the current oven
temperature.
NOTE: The cook time that appears in the display is the estimated required cook time as
calculated by the oven control. It may be different than the time you entered. A beep will alert
you to check the food’s doneness with at least 2 minutes remaining on the timer. Follow the
prompts on the display to select more time if desired.
8. At the end of the cook time, a beep will alert you to check the food’s doneness. Follow the
prompts on the display to select more time if desired. Unless more time is selected, the bake
element turns off.
9. Press CANCEL when finished.
1. Press BROIL.
2. Select the broiling temperature by pressing 1 - high (500°F [260°C]), 2 - medium (450°F
[232°C]) or 3 - low (400°F [204°C]). The default setting is high.
3. Press START and allow the oven to preheat for 5 minutes.
4. Position the cookware in the oven and leave the door open 6” (15 cm) at the broil
stop position.
5. Press CANCEL when finished.
1. Press CONVECT once to select convection baking, twice for convection roasting, or 3 times
for convection broiling.
2. Press the number keypads to set a temperature other than 350°F (177°C) in 5° increments
between 170°F and 500°F (77°C and 260°C).
3. Press START. Auto conversion will reduce the temperature by 25°F (15°C).
4. To change the temperature, repeat steps 1 and 2. Press START or wait 5 seconds for the
change to take effect.
5. Press CANCEL when finished.
Food must be at serving temperature before placing it in the warmed oven.
1. Press KEEP WARM.
2. Set temperature between 145°F (63°C) and 190°F (88°C) using the number keypads. The
default temperature is 170°F (75°C).
3. Press START.
4. Press CANCEL when finished.
The START TIME keypad is used to enter the starting time for an oven function with a
delayed start.
Timed Cooking allows the oven to be set to turn on at a certain time of day, cook for a set length
of time, and/or shut off automatically. Delay start should not be used for foods such as breads
and cakes because they may not bake properly.
To set a Timed Cook or a Delayed Timed Cook, see “Cook Time” section.
Provides the fastest preheat time for the BAKE function.
1. Press RAPID PREHEAT.
2. Press the number keypads in response to the scrolling text to enter the Bake temperature.
3. Press START.
4. A reminder tone will sound when the preheat temperature is reached. Place food inside
the oven.
NOTE: This feature should only be used for one-rack baking. Unused racks should be removed
prior to Rapid Preheat. A standard rack should be used for Rapid Preheat.
If preheating for the Bake cycle has already started, Rapid Preheat may be started directly by
pressing RAPID PREHEAT.
Press WARM ZONE ON to select the warming element on the cooktop, then press START.
Press WARM ZONE OFF to turn off the warming element.
5
KEYPADFEATUREINSTRUCTIONS
AQUALIFT
SELF CLEAN
START
hold 3 sec.
SETTINGSOven use
Clean cycle
Oven control
lockout
functions
See the “Clean Cycle” section.
No keypads will function with the controls locked.
1. Check that the oven and the Timer are off.
2. Press and hold START keypad for 3 seconds.
3. If enabled, a tone will sound, and “CONTROL LOCKED” will be displayed.
4. Repeat to unlock.
Enables you to personalize the audible tones and oven operation to suit your needs. See the
“Oven Use” section.
COOKTOP USE
WARNING
Fire Hazard
Turn off all controls when done cooking.
Failure to do so can result in death or fire.
The control knobs can be set to anywhere between HI and LO.
Push in and turn to setting.
REMEMBER: When range is in use, the entire cooktop area
may become hot.
■ Avoid storing jars or cans above the cooktop. Dropping
a heavy or hard object onto the cooktop could crack the
cooktop.
■ To avoid damage to the cooktop, do not leave a hot lid on
the cooktop. As the cooktop cools, air can become trapped
between the lid and the cooktop, and the ceramic glass could
break when the lid is removed.
■ For foods containing sugar in any form, clean up all spills and
soils as soon as possible. Allow the cooktop to cool down
slightly. Then, while wearing oven mitts, remove the spills
using a scraper while the surface is still warm. If sugary spills
are allowed to cool down, they can adhere to the cooktop
and can cause pitting and permanent marks.
■ To avoid scratches, do not slide cookware or bakeware
across the cooktop. Aluminum or copper bottoms and rough
finishes on cookware or bakeware could leave scratches or
marks on the cooktop.
■ Do not cook popcorn in prepackaged aluminum containers
on the cooktop. They could leave aluminum marks that
cannot be removed completely.
■ To avoid damage to the cooktop, do not allow objects that
could melt, such as plastic or aluminum foil, to touch any part
of the entire cooktop.
■ To avoid damage to the cooktop, do not use the cooktop as a
cutting board.
■ Use cookware about the same size as the surface cooking
area. Cookware should not extend more than ½" (1.3 cm)
outside the area.
B
Ceramic Glass
The surface cooking area will glow red when an element is on.
Some parts of the surface cooking area may not glow red when
an element is on. This is normal operation. It will also randomly
cycle off and back on again, even while on Hi, to keep the
cooktop from extreme temperatures.
It is normal for the surface of light colored ceramic glass to
appear to change color when surface cooking areas are hot. As
the glass cools, it will return to its original color.
Clean the cooktop after each use to help avoid scratches, pitting,
abrasions and to condition the glass surface. Ceramic glass
cooktop cleaner and a cooktop scraper are also recommended
for stubborn soils. Do not use abrasive cleaners, cleaning pads or
harsh chemicals for cleaning. The Cooktop Care Kit Part Number
31605 contains all of the items needed to clean and condition
your ceramic glass cooktop. Refer to the “Range Care” section
for additional information.
IMPORTANT: To avoid permanent damage to the cooktop
surface and to make soils easier to remove, clean the cooktop
after each use to remove all soils.
A
C
A. Surface cooking area
B. Cookware/canner
C. ½" (1.3 cm) maximum overhang
6
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.