Whirlpool LTE5243DQ7, LTE5243DT7, LTE6234DQ6, LTE6234DT6, LTG5243DQ7 Owner’s Manual
...
WASHER/DRYERUSER INSTRUCTIONS
INSTRUCCIONES PARA EL USUARIO
DE LALAVADORA/SECADORA
INSTRUCTIONSD'UTILISATION
.#
DE LALAVEUSE/SECHEUSE
Table of Contents /Indlce /Table des matieres
ASSISTANCE OR SERVICE ............................ 1
WASHER/DRYER SAFETY ............................. 2
WASHER USE .................................................. 4
DRYER USE ...................................................... 5
WASHER/DRYER CARE ................................. 6
TROUBLESHOOTING WASHER .................... 8
TROUBLESHOOTING DRYER ...................... 10
WARRANTY .................................................... 12
AYUDA O SERVICIO TleCNICO .................... 13
SEGURIDAD DE LA
LAVADORA/SECADORA ............................... 13
USO DE LA LAVADORA ................................ 16
USO DE LA SECADORA ............................... 17
CUlDADO DE LA
LAVADORA/SECADORA ............................... 18
SOLUCION DE PROBLEMAS
DE LA LAVADORA ......................................... 20
SOLUCION DE PROBLEMAS
DE LA SECADORA ........................................ 22
GARANTiA ...................................................... 24
Assistance or Service
If you need assistance or service, first see the "Troubleshooting"
section. Additional help is available by calling our Customer
eXperience Center at 1-800-253-1301 from anywhere in the
U.S.A., or write:
Whirlpool Corporation
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Information may also be obtained by visiting our website at
www.whirlpool.com.
In Canada, for assistance, installation or service, call us at
1-800-807-6777, or write:
Whirlpool Canada LP
Customer Interaction Centre
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
In Canada, visit www.whirlpool.ca.
Please include a daytime phone number in your correspondence.
• o,.
ASSISTANCE OU SERVICE .......................... 25
SleCURITle DE LA
LAVEUSE/SF=CHEUSE ................................... 25
UTILISATION DE LA LAVEUSE .................... 28
UTILISATION DE LA SleCHEUSE ................. 29
ENTRETIEN DE LA
LAVEUSE/SF=CHEUSE ................................... 30
DlePANNAGE DE LA LAVEUSE .................... 32
DlePANNAGE DE LA SleCHEUSE ................. 34
GARANTIE ...................................................... 36
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your appliance to help
you obtain assistance or service if you ever need it. You will need
to know your complete model number and serial number. You can
find this information on the model and serial number label, located
at the top inside dryer door well.
Dealer name
Serial number
Address
Phone number
Model number
Purchase date
8578179B
AGINE _
WASHER/DRYERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
m WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building, or area of all occupants.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic
precautions, including the following:
[] Read all instructions before using the washer/dryer.
[] Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire.
[] Do not wash or dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry-cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Do not allow children to play on or in the washer/dryer.
Close supervision of children is necessary when the
washer/dryer is used near children.
[] Before the washer/dryer is removed from service or
discarded, remove the doors to the washer/dryer
compartments.
[] Do not reach into the washer/dryer if the tub, agitator or
drum is moving.
[] Do not install or store the washer/dryer where it will be
exposed to the weather.
[] Do not tamper with controls.
[] Clean dryer lint screen before or after each load.
SAVE THESE INSTRUCTIONS
[] Under certain conditions, hydrogen gas may be produced
in a hot water system that has not been used for 2 weeks
or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using
the washing machine, turn on all hot water faucets and let
the water flow from each for several minutes. This will
release any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this time.
[] Do not repair or replace any part of the washer/dryer or
attempt any servicing unless specifically recommended in
this Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
[] Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
[] Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
[] Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
[] The interior of the machine and dryer exhaust vent should
be cleaned periodically by qualified service personnel.
[] See "Electrical Requirements" section for grounding
instructions.
Your dryer must be properly installed and vented to achieve
maximum drying efficiency and shorten drying times. Use the
minimum recommended installation clearances found in the
Installation Instructions. See the Installation Instructions for more
information.
Fire Hazard
Use a heavy metal vent.
Do not use a piaetic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
If the dryer is not properly installed and vented, it will not be
covered under the warranty. Proper venting of your dryer is
important for satisfactory drying results. See the Installation
Instructions for more detail.
NOTE: Service calls caused by improper venting will be paid for
by the customer, whether it was a paid installation or self-
installed.
f. Do not use plastic vent or metal foil vent. Use 4" (10.2 cm)
metal or flexible metal vent. Do not kink or crush flexible metal
vent. It must be completely extended to allow adequate
exhaust air to flow. Check vent after installation. Refer to the
Installation Instructions for proper length requirements of vent.
2. Use a 4" (10.2 cm) exhaust hood.
3. Usethestraightestpathpossiblewhenroutingthevent.
Good Better
4.
Use clamps to seal all joints. Do not use duct tape, screws or
other fastening devices that extend into the interior of the vent
to secure vent.
5.
Clean exhaust vent periodically, depending on use, but at
least every 2 years, or when installing your dryer in a new
location. When cleaning is complete, be sure to follow the
Installation Instructions supplied with your dryer for final
product check.
WASHERUSE
For these suggested full-sized loads, set the LOAD SIZE selector to the highest load size setting.
LARGE CAPACITY WASHERS
Heavy Work
Clothes Press
2 pair of pants 2 double sheets 8 bath towels 2 camisoles 1 double sheet 2 pair of pants
3 shirts 4 pillowcases 8 hand towels 4 slips 1 tablecloth 2 blouses
3 jeans 6 T-shirts 10 washcloths 6 undergarments 1 dress 4 shirts
1 coverall 6 pair of shorts 1 bath mat 2 sets of sleepwear 1 blouse 4 tops
Heavy Work
Clothes
2 pair of pants
3 shirts
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
Measure detergent and pour it into the washer. If desired, add
powdered or liquid color safe bleach. Drop a sorted load of
clothes loosely into your washer.
Mixed Load Towels Delicates Permanent Knits
2 shirts 1 child's outfit 2 pair of pants 2 dresses
2 blouses 3 shirts
6 handkerchiefs 2 pillowcases
COMPACT WASHERS
Mixed Load Towels Delicates Permanent Knits
Press
1 pair of pants 9 bath towels 1 camisole 6 shirts 2 pair of pants
2 pillowcases -or- 2 slips -or- 2 shirts
2 shirts 6 bath towels 4 undergarments 2 double sheets -or-
1 T-shirt 3 hand towels 1 set of sleepwear 2 pillowcases 3 dresses
Fire Hazard
6 washcloths 1 half slip -or-
• Load evenly to maintain washer balance. Mix large and
small items. Items should move easily through the wash
water. Overloading can cause poor cleaning.
2=
(OPTIONAL) Add liquid chlorine bleach.
Always measure liquid chlorine bleach. Do not guess. Do not
use more than 1 cup (250 mL) for a full load. Follow
manufacturer's directions for safe use. Use a cup with a
pouring spout to avoid spilling.
Let the washer fill and begin agitating the load. Add bleach to
the wash cycle so it can be removed in the rinse cycle. Pour
bleach around the agitator, not directly onto the load.
• Follow directions on the care labels. Do not use chlorine
bleach on wool, silk, spandex, acetates, or some flame-
retardant fabrics.
NOTE: Undiluted bleach will damage any fabric it touches.
The damage appears as rips, holes, tears, or color loss and
may not show up until several washings later.
3=
(OPTIONAL) Add liquid fabric softener.
NOTE: Your washer/dryer does not come with a fabric
softener dispenser installed.
2 single sheets
2 pillowcases
Tofindoutwhetheryourmodelallowsfabricsoftener
dispenserusageandforinformationonordering,refertothe
frontpageofthismanualorcallthedealerfromwhomyou
purchasedyourwasher/dryer.AskforPartNumber3350834.
NOTE:Donotspillordripanyfabricsoftenerontotheclothes.
Undilutedfabricsoftenercanstainfabrics.Alwaysdilutefabric
softenerwithwarmwater.Toomuchfabricsoftenercanmake
someitems(diapersandtowels)nonabsorbent.Ifthis
happens,donotuseitineveryload,oruselessofitineach
load.
Style1:Withliquidfabricsoftenerdispenser(onsome
models)
• Useonlyliquidfabricsoftenerinthisdispenser.Pour
measuredliquidfabricsoftenerintothedispenser.
Softenerisaddedautomaticallyduringtherinseportionof
thecycle.Diluteliquidfabricsoftenerbyfillingthe
dispenserwithwarmwateruntilliquidreachesthe
crossbarinthedispenseropening.
Style2:Withoutliquidfabricsoftenerdispenser(onsome
models)
• InthefinalrinseONLY,addfabricsoftenerthathasbeen
dilutedwith1/2to1cup(125to250mL)warmwater.
4. Closethewasherlid.Washerwillnotagitateorspinwiththe
lidopen.
5. TurntheWATERLEVELselectortothecorrectsettingforyour
washloadandthetypeoffabricbeingwashed.Youmay
changetheloadsizeorwaterlevelselectionafterthewasher
hasstartedfillingbyturningtheselectortoadifferentsetting.
6. SettheTEMPERATUREselectortothecorrectsettingforthe
typeoffabricandsoilsbeingwashed.Usethewarmestwater
safeforfabric.Followgarmentlabelinstructions.
NOTE:Inwashwatertemperaturescolderthan60°F(15.6°C),
detergentsdonotdissolvewell.Soilscanbedifficultto
remove.Somefabricscanretainwearwrinklesandhave
increasedpilling(theformationofsmalllint-likeballsonthe
surfaceofgarments).
7. PushintheCycleControlknobandturnitclockwisetothe
washcycleyouwant.Reducethewashtimewhenusinga
smallloadsizesetting.PullouttheCycleControlknobtostart
thewasher.
To stop or restart your washer:
• To stop the washer at any time, push in the Cycle
Control knob.
• To restart the washer, close the lid (if open) and pull out the
Cycle Control knob.
DRYERUSE
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer,
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in death,
explosion, or fire.
This booklet covers several different models. Your dryer may not
have all of the cycles and features described.
Before using your dryer, wipe the dryer drum with a damp cloth to
remove dust from storing and shipping.
1. Clean lint screen before each load. See "Cleaning the Lint
Screen."
2. Load clothes loosely into the dryer and close the door. Do not
pack the dryer. Allow space for clothes to tumble freely.
3. Turn the Cycle Control knob to the recommended cycle for the
type of load being dried. Use the Energy Preferred Automatic
Setting to dry most heavy to medium weight fabrics.
Fire Hazard
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Items containing foam, rubber, or plastic must be dried
on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in death
or fire.
4. (OPTIONAL) Your dryer may have an END OF CYCLE SIGNAL.
The signal is helpful when drying items that should be
removed from the dryer as soon as it stops. The End of Cycle
signal is part of the Start button and is selectable. Turn the
Start button to ON or OFF. The signal will sound only if the
selector is set to On.
5. If desired, add fabric softener sheet. Follow package
instructions.
6. Press the PUSH TO START button.
Stopping and Restarting
You can stop your dryer anytime during a cycle.
To stop your dryer
Open the dryer door or turn the Cycle Control knob to OFE
WASHER/DRYERCARE
NOTE: The Cycle Control knob should point to an Off area when
the dryer is not in use.
To restart your dryer
Close the door. Select a new cycle and temperature (if desired).
Press the PUSH TO START button.
Keep washer/dryer area clear and free from items that would
obstruct the flow of combustion and ventilation air.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Failure to do so can result in death, explosion, or fire.
Cleaning the exterior
Use a soft, damp cloth or sponge to wipe up any spills such as
detergent or bleach. Occasionally wipe the outside of your washer
to keep it looking new.
Cleaning the interior
Clean your washer interior by mixing 1cup (250 mL) of chlorine
bleach and 2 scoops or caps full of detergent. Pour this into your
washer and run it through a complete cycle using hot water.
Repeat this process if necessary.
NOTE: Remove any hard water deposits using only cleaners
labeled as washer safe.
Cleaning the liquid fabric softener dispenser (on some
models):
1. Remove dispenser by grasping top with both hands and
squeezing, while pushing upward with thumbs.
2. Rinse dispenser under a warm water faucet, then replace it.
NOTE: If your model has a liquid fabric softener dispenser, do not
wash clothes with this dispenser removed. Do not add detergent
or bleach to this dispenser; it is for liquid fabric softener only.
Replace inlet hoses after 5 years of use to reduce the risk of hose
failure. Periodically inspect and replace inlet hoses if bulges,
kinks, cuts, wear or leaks are found.
When replacing your inlet hoses, mark the date of replacement on
the label with a permanent marker.
Clean the lint screen before each load. A screen blocked by lint
can increase drying time.
IMPORTANT:
• Do not run the dryer with the lint screen loose, damaged,
blocked or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
• If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint.
Every Load Cleaning
Style 1:
1. The lint screen is located inside the dryer on the back wall.
Pull out the lint screen and its cover.
2. Separate the cover and the screen by squeezing the screen
and pulling on the cover at the same time.
3. Roll lint off the screen with your fingers. Do not rinse or wash
screen to remove lint. Wet lint is hard to remove.
4. Put the lint screen and cover back together and push firmly
back into place.
Style 2:
1. The lint screen is located inside the dryer in the front door well.
Pull the lint screen straight up.
2. Roll lint off the screen with your fingers. Do not rinse or wash
screen to remove lint. Wet lint is hard to remove.
3. Push the lint screen firmly back into place.
As Needed Cleaning
Laundry detergent and fabric softener residue can build up on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off the screen.
Clean the lint screen (as outlined following) every 6 months, or
more frequently if it becomes clogged due to a residue buildup.
1. Roll lint off the screen with your fingers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel. Replace screen
in dryer.
To clean dryer drum
1. Apply a nonflammable household cleaner to the stained area
of the drum and rub with a soft cloth until stain is removed.
2. Wipe drum thoroughly with a damp cloth.
3. Tumble a load of clean cloths or towels to dry the drum.
NOTE: Garments that contain unstable dyes, such as denim blue
jeans or brightly colored cotton items, may discolor the dryer
interior. These stains are not harmful to your dryer and will not
stain future loads of clothes. Dry unstable dye items inside out to
avoid dye transfer.
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
From Inside the Exhaust Vent
In Canada
Lint should be removed every 2 years, or more often, depending
on dryer usage.
Install and store your washer/dryer where it will not freeze.
Because some water may stay in the hoses, freezing can damage
your washer/dryer. If storing or moving your washer/dryer during
freezing weather, winterize it.
Non-use or vacation care
Operate your washer/dryer only when you are at home. If you will
be on vacation or not using your washer/dryer for an extended
period of time, you should:
• Unplug washer/dryer or disconnect power.
• Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
To winterize washer/dryer
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.
4. Run washer on a drain and spin setting for about 30 seconds
to mix the antifreeze and water.
5. Unplug washer/dryer or disconnect power.
To use washer/dryer again
1. Flush water pipes and hoses.
2. Reconnect water inlet hoses.
3. Turn on both water faucets.
4. In the U.S.A.
Electrical Shock Hazard
Plug into a grounded 4 prong outlet.
Failure to do so can result in death or electrical shock.
• Plug in washer/dryer or reconnect power.
5. Run the washer through a complete cycle with 1 cup (250 mL)
of detergent to clean out antifreeze.
To transport the washer/dryer
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. If washer/dryer will be moved during freezing weather, put in a
qt (1 L) of R.V.-type antifreeze in the basket. Run washer on a
spin setting for about 30 seconds to mix the antifreeze and
water.
4. Disconnect the drain from the drain system.
5. Unplug washer/dryer or disconnect power. Disconnect wiring
if washer/dryer is direct wired.
6. Disconnect the exhaust vent.
7. Wash lint screen.
8. Make sure leveling legs are secure.
9. Place the inlet hoses into the basket.
10. Drape the power cord and drain hose over edge and into the
basket.
11. Use masking tape to secure the washer lid and dryer door.
Reinstalling your washer/dryer
1. Follow the "Installation Instructions" to locate, level and
connect the washer/dryer.
2. Run the washer through a complete cycle with 1 scoop or
capful of detergent to clean the washer and remove the
antifreeze, if used.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
• Plug inwasher/dryer or reconnect power.
TROUBLESHOOTINGWASHER
First try the solutions suggested here and possibly avoid the cost of a service call...
Noisy, vibrating, off-balance
• Is the floor flexing, sagging or not level? Flooring that flexes
or is uneven can contribute to noise and vibration of the
washer. A %" (1.9 cm) piece of plywood under the washer will
reduce the sounds. See the Installation Instructions.
• Is the washer/dryer level? The washer/dryer must be level.
See the Installation Instructions.
• Is the load balanced? Evenly distribute the load in the
washer basket and make sure the height of the load does not
exceed the top row of basket holes.
• Did you completely remove the yellow shipping strap with
cotter pins? See the Installation Instructions.
• Are the gears engaging after the drain and before spin, or
is the upper part of agitator clicking during wash? These
are normal washer noises.
Is the washer gurgling or humming? When the washer
drains, the pump will make a continuous humming with
periodic gurgling or surging sounds as the final amounts of
water are removed. This is normal.
• The washer basket moves while washing. This is normal.
Leaking
• Are the fill hoses tight?
• Are the fill hose gaskets properly seated? Check both ends
of each hose. See the Installation Instructions.
• Is the drain hose properly installed? The drain hose should
be secured to the drainpipe or laundry tub. See the Installation
Instructions.
• Is the sink or drain clogged? Sink and drainpipe must be
able to carry away 17 gal. (64 L)of water per minute. If sink or
drainpipe is clogged or slow, water can back up out of
drainpipe or sink. Check household plumbing (laundry tubs,
faucets, drainpipe, water pipes) for leaks.
• Is water splashing off the tub ring? Center the tub before
starting the washer.
• Is water splashing off the load? Evenly distribute the load in
the washer basket and make sure the height of the load does
not exceed the top row of basket holes. The fill or spray rinses
can splash off the load.
Dispenser clogged (on some models)
• Did you follow the manufacturer's directions when adding
fabric softener to the dispenser (on some models)?
Measure fabric softener and slowly pour into the dispenser.
Wipe up all spills. Dilute fabric softener in the fabric softener
dispenser.
Washer won't run, fill, rinse or agitate; washer stops
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
• Is the power cord plugged into a grounded 3 prong outlet?
Plug power cord into a grounded 3 prong outlet.
• Are you using an extension cord? Do not use an extension
cord.
• Is the indicator on the Cycle Control knob properly lined
up with a cycle? Turn the Cycle Control knob to the right
slightly and pull to start.
• Are the water inlet valve screens clogged? Turn off the
water and remove inlet hoses from the washer. Remove any
accumulated film or particles. Reinstall hoses, turn on water
and check for leaks.
Are both the hot and cold water faucets turned on? Turn
on the water.
Is the water inlet hose kinked? Straighten the hoses.
Does the water level seem too low, or does the washer
appear to not fill completely? The top of the agitator is much
higher than the highest water level. This is normal and
necessary for clothes to move freely.
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse, or reset the circuit breaker. Ifthe
problem continues, call an electrician.
Is the washer in a normal pause in the cycle? The washer
pauses for about 2 minutes during certain cycles. Allow the
cycle to continue. Some cycles feature periods of agitation
and soak.
Is the washer overloaded? Wash smaller loads.
Is the lid open? The lid must be closed during operation.
Washer will not agitate or spin with the lid open.
Washer continues to fill or drain; cycle seems stuck
• Is the top of drain hose lower than the control knobs on
washer? The top of the drain hose must be at least
39" (99 cm) above the floor. See the Installation Instructions.
• Does the drain hose fit too tightly in the standpipe, or is it
taped to the standpipe? The drain hose should be loose yet
fit securely. Do not seal the drain hose with tape. The hose
needs an air gap. See the Installation Instructions.
Washer won't drain or spin; water remains in washer
• Is the drain hose clogged, or the end of the drain hose
more than 96" (244 cm) above the floor? See the Installation
Instructions,
• Is the lid open? The lid must be closed during operation.
Washer will not agitate or spin with the lid open.
• Is there excessive sudsing? Always measure detergent.
Follow manufacturer's directions, If you have very soft water,
you might need to use less detergent.
Wash/Rinse temperature
• Are the hot and cold water inlet hoses reversed? See
"Connect Inlet Hoses."
• Are you washing many loads? As your frequency of loads
washed increases, the water temperature may decrease for
hot and warm temperatures, This is normal,
Load too wet
• Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed (if available).
• Did you wash an extra-large load? A large unbalanced load
could result in a reduced spin speed and wet clothes at the
end of the cycle. Evenly distribute the load and make sure the
height of the load does not exceed the top row of basket
holes.
Residue or lint on load
• Did you sort properly? Sort lint givers (towels, chenille) from
lint takers (corduroy, synthetics). Also sort by color.
• Did you overload the washer? The wash load must be
balanced and not overloaded, Clothes should move freely.
Lint or powdered detergent can be trapped in the load if
overloaded. Wash smaller loads.
Did you select the correct water level? The water level
should be correct for the load size. The load should be under
water.
• Did you use enough detergent? Follow manufacturer's
directions, Use enough detergent to hold the lint in the water.
• Did you line dry your clothing? If so, you can expect some
lint on the clothing. The air movement and tumbling of a dryer
removes lint from the load.
• Was paper or tissue left in the pockets?
• Is your water colder than 60°F (15.6°C)? Wash water colder
than 60°F (15.6°C) may not completely dissolve the detergent.
• Did you use the proper cycle time and agitation speed for
the load? Reducing wash time (duration) and agitation speed
are ways to reduce lint.
Load is wrinkled, twisted or tangled
• Did you unload the washer promptly? Unload the washer as
soon as it stops.
• Did you use the right cycle for the load being washed?
Use cycles with shorter wash times and low wash and spin
speeds (if available) to reduce wrinkling, tangling and twisting.
• Did you overload the washer? The wash load must be
balanced and not overloaded. Loads should move freely
during washing to reduce wrinkling, tangling and twisting.
• Was the wash water warm enough to relax wrinkles? If
safe for the load, use warm or hot wash water. Use cold rinse
water.
Are the hot and cold water hoses reversed? Check to be
sure the hot and cold water hoses are connected to the right
faucets, A hot rinse followed by spin will cause wrinkling, See
the Installation Instructions,
• Did you wrap items around the agitator? Drop items loosely
into the washer. Do not wrap items around the agitator.
Stains, gray whites, dingy colors
• Did you properly sort the load? Dye transfer can occur when
mixing whites and colors in a load. Sort dark clothes from
whites and lights.
• Was the wash temperature too low? Use hot or warm
washes if safe for the load. Make sure your hot water system
is adequate to provide a hot water wash.
• Did you use enough detergent, or do you have hard
water? Use more detergent for washing heavy soils in cold or
hard water.
• Are the hot and cold water hoses reversed? Check to be
sure the hot and cold water hoses are connected to the right
faucets, See the Installation Instructions.
Did you follow the manufacturer's directions when adding
detergent and fabric softener? Measure detergent and
fabric softener. Use enough detergent to remove soil and hold
it in suspension. Dilute fabric softener and add to the rinse
portion of a cycle only. Do not drip fabric softener onto
clothes.
• Is there above average iron (rust) in water? You may need
to install an iron filter.
Garments damaged
• Were sharp items removed from pockets before washing?
Empty pockets, zip zippers, snap or hook fasteners before
washing to avoid snagging and tearing of load.
• Were strings and sashes tied to avoid tangling? Straps and
strings can easily become entangled in the load, causing
strain on seams and tearing.
• Were items damaged before washing? Mend rips and
broken threads in seams before washing.
TROUBLESHOOTINGDRYER
First try the solutions suggested here and possibly avoid the cost of a service call...
Did you overload the washer? The wash load must be
balanced and not overloaded. Loads should move freely
during washing.
Did you add chlorine bleach properly? Do not pour chlorine
bleach directly onto load. Wipe up bleach spills. Undiluted
bleach will damage fabrics. Do not place load items on top of
the bleach dispenser when loading and unloading the washer
(on some models). Do not use more than than the
manufacturer's recommended amount for a full load.
• Did you follow the manufacturer's care label instructions?
Dryer will not run
• Has a household fuse blown, or has a circuit breaker
tripped? There may be 2 fuses or circuit breakers for the
dryer. Check that both fuses are intact and tight, or that both
circuit breakers have not tripped. Replace the fuse or reset the
circuit breaker. Ifthe problem continues, call an electrician.
• Is the correct power supply available? Electric dryers
require 240 volt power supply. Check with a qualified
electrician.
• Was a regular fuse used? Use a time-delay fuse.
• Is the dryer door firmly closed?
• Was the PUSH TO START DRYER button firmly pressed?
No heat
• Has a household fuse blown, or has a circuit breaker
tripped? The drum may be turning, but you may not have
heat. Electric dryers use 2 fuses or circuit breakers. Replace
the fuse or reset the circuit breaker. If a problem continues,
call an electrician.
• For gas dryers, is the valve open on the supply line?
Unusual sounds
• Has the dryer had a period of non-use? If the dryer hasn't
been used for a while, there may be a thumping sound during
the first few minutes of operation.
• Is a coin, button, or paper clip caught between the drum
and front or rear of the dryer? Check the front and rear
edges of the drum for small objects. Clean out pockets before
laundering.
• Is it a gas dryer? The gas valve clicking is a normal operating
sound.
• Are the four legs installed, and is the dryer level front to
back and side to side? The dryer may vibrate if not properly
installed. See the Installation Instructions.
• Is the clothing knotted or balled up? When balled up, the
load will bounce, causing the dryer to vibrate. Separate the
load items and restart the dryer.
Timer does not noticeably advance
• Is the dryer set to Timed or Air Dry?
The timer moves slowly and continuously for the time setting.
• Is the dryer set to Automatic Drying?
The timer moves only when the clothing is mostly dry.
10
Clothes are not drying satisfactorily, drying times are too long,
or load is too hot
• Is the lint screen clogged with lint? Lint screen should be
cleaned before each load.
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
Is the exhaust vent or outside exhaust hood clogged with
lint, restricting air movement? Run the dryer for
5-10 minutes. Hold your hand under the outside exhaust hood
to check air movement. If you do not feel air movement, clean
exhaust system of lint or replace exhaust vent with heavy
metal or flexible metal vent. See the Installation Instructions.
Are fabric softener sheets blocking the grille? Use only one
fabric softener sheet, and use it only once.
Is the exhaust vent the correct length? Check that the
exhaust vent is not too long or has too many turns. Long
venting will increase drying times. See the Installation
Instructions.
Is the exhaust vent diameter the correct size? Use
4" (10.2 cm) diameter vent material.
• Is the dryer located in a closet? Closet doors must have
ventilation openings at the top and bottom of the door. A
minimum of 1" (2.5 cm) of airspace is recommended for the
front of the dryer, and, for most installations, the rear of the
dryer requires 5" (12.7 cm). See the Installation Instructions.
• Has an air dry cycle been selected? Select the right cycle
for the types of garments being dried.
• Is the load too large and heavy to dry quickly? Separate the
load to tumble freely.
Lint on load
• Is the lint screen clogged? Lint screen should be cleaned
before each load.
Stains on load or drum
• Was dryer fabric softener properly used? Add dryer fabric
softener sheets at the beginning of the cycle. Fabric softener
sheets added to a partially dried load can stain your garments.
Drum stains are caused by dyes in clothing (usually blue
jeans). This will not transfer to other clothing.
Loads are wrinkled
• Was the load removed from dryer at the end of the cycle?
• Was the dryer overloaded? Dry smaller loads that can
tumble freely.
Odors
• Have you recently been painting, staining or varnishing in
the area where your dryer is located? Ifso, ventilate the
area. When the odors or fumes are gone from the area, rewash
and dry the clothing.
• Is the electric dryer being used for the first time? The new
electric heating element may have an odor. The odor will be
gone after the first cycle.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer,
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
• Is the dryer located in a room with temperature below
45°F (7°0)? Proper operation of dryer cycles requires
temperatures above 45°F (7°C).
11
Loading...