Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can
happen if the instructions are not followed.
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
–
or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
–
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
Installation and service must be performed by a qualified installer, service agency or
–
the gas supplier.
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list
of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and
requires businesses to warn of potential exposure to such substances.
WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or
other reproductive harm.
This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde,
carbon monoxide, toluene, and soot.
3
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door
without the anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
See the installation instructions for details.
Failure to follow these instructions can result in death or serious burns to children
and adults.
Anti-Tip Bracket
Range Foot
Making sure the anti-tip bracket is installed:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor.
• Slide range back so rear range foot is under anti-tip bracket.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical
shock, injury to persons, or damage when using the
range, follow basic precautions, including the
following:
WARNING:
■
TIPPING OF THE RANGE, THE RANGE MUST BE
SECURED BY PROPERLY INSTALLED ANTI-TIP
DEVICES. TO CHECK IF THE DEVICES ARE
INSTALLED PROPERLY, SLIDE RANGE FORWARD,
LOOK FOR ANTI-TIP BRACKET SECURELY
ATTACHED TO FLOOR, AND SLIDE RANGE BACK
SO REAR RANGE FOOT IS UNDER ANTI-TIP
BRACKET.
CAUTION:
■
children in cabinets above a range or on the
backguard of a range – children climbing on the
range to reach items could be seriously injured.
■
Proper Installation – The range, when installed, must
be electrically grounded in accordance with local
codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70.
the range must be electrically grounded in accordance
with Canadian Electrical Code. Be sure the range is
properly installed and grounded by a qualified technician.
■
This range is equipped with a three-prong grounding
plug for your protection against shock hazard and
should be plugged directly into a properly grounded
receptacle. Do not cut or remove the grounding prong
from this plug.
TO REDUCE THE RISK OF
Do not store items of interest to
In Canada,
■
Disconnect the electrical supply before servicing the
appliance.
■
Never Use the Range for Warming or Heating the
Room.
■
Injuries may result from the misuse of appliance doors
or drawers such as stepping, leaning, or sitting on the
doors or drawers.
■
Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
■
Storage in or on the Range – Flammable materials
should not be stored in an oven or near surface units.
■
Top burner flame size should be adjusted so it does
not extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
■
Before Self-Cleaning the Oven – Remove broiler pan
and other utensils. Wipe off all excessive spillage
before initiating the cleaning cycle.
SAVE THESE INSTRUCTIONS
4
PARTS AND FEATURES
This manual covers several different models. The range you have purchased may have some or all of the parts and features listed. The
locations and appearances of the features shown here may not match your model.
Cooktop Control Panel
1
Range
2
Surface Burner Locator
1.
Left Rear Burner Control
2.
1
2
3
4
5
3
Left Front Burner Control
3.
Right Rear Burner Control
4.
ONON
Right Front Burner Control
5.
54
9
10
11
12
13
14
6
7
8
Oven Vent
1.
Center Grate (on some models)
2.
Left Rear Surface Burner and Grate
3.
Left Front Surface Burner and Grate
4.
Automatic Oven Light Switch
5.
Anti-Tip Bracket
6.
Model and Serial Number Plate
7.
(behind left side of Broiler Door)
Broiler Door
8.
Manual Oven Light Switch
9.
Electronic Oven Control
10.
Right Rear Surface Burner and Grate
11.
Right Front Surface Burner and Grate
12.
Cooktop Control Panel
13.
Door Gasket
14.
5
COOKTOP USE
Power failure
In case of prolonged power failure, the surface burners can be
lighted manually. Hold a lighted match near a burner and turn
knob counterclockwise to LITE. After burner lights, turn knob to
setting.
Cooktop Controls
WARNING
Fire Hazard
Do not let the burner flame extend beyond the
edge of the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in
death or fire.
Electric ignitors automatically light the surface burners when
control knobs are turned to LITE.
Before setting a control knob, place filled cookware on the grate.
Do not operate a burner using empty cookware or without
cookware on the grate.
REMEMBER: When range is in use or (on some
models) during the Self-Cleaning cycle, the entire
cooktop area may become hot.
Sealed Surface Burners
1
2
3
4
To S et:
Push in and turn knob counterclockwise to LITE.
1.
All four surface burners will click. Only the burner with the
control knob turned to LITE will produce a flame.
Turn knob anywhere between HIGH and LOW. The clicking
2.
will stop. Use the following chart as a guide when setting heat
levels.
SETTINGRECOMMENDED USE
LITE
HI
MED
LO
■ Light the burner.
■ Start food cooking.
■ Bring liquid to a boil.
■ Hold a rapid boil.
■ Quickly brown or sear food.
■ Fry or sauté foods.
■ Cook soups, sauces and gravies.
■ Stew or steam foods.
■ Keep food warm.
■ Melt chocolate or butter.
■ Simmer.
5
1. Burner cap
2. Alignment pins
3. Ignitor
4. Burner
5. Gas tube opening
IMPORTANT:
ventilation air around the burner grate edges.
Burner cap:
surface burner. A clean burner cap will help prevent poor ignition
and uneven flames. Always clean the burner cap after a spillover
and routinely remove and clean the caps according to the
“General Cleaning” section.
Gas tube opening:
opening for the burner to light properly.
soil and do not allow spills, food, cleaning agents or any
other material to enter the gas tube opening.
spillovers by always using a burner cap.
Do not obstruct the flow of combustion and
Always keep the burner cap in place when using a
Gas must flow freely throughout the gas tube
Keep this area free of
Protect it from
1
2
¹⁄₂
1. 1-1
" (25-38 mm)
2. Burner ports
Burner ports:
and shape as shown above. A good flame is blue in color, not
yellow. Keep this area free of soil and do not allow spills, food,
cleaning agents or any other material to enter the burner ports.
Check burner flames occasionally for proper size
6
To C lea n:
IMPORTANT:
the oven and cooktop are cool. Do not use oven cleaners, bleach
or rust removers.
Remove the burner cap from the burner base and clean
1.
according to “General Cleaning” section.
Clean the gas tube opening with a damp cloth.
2.
Clean clogged burner ports with a straight pin as shown. Do
3.
not enlarge or distort the port. Do not use a wooden
toothpick. If the burner needs to be adjusted, contact a
trained repair specialist.
Replace the burner cap, making sure that alignment pins are
4.
properly aligned with the burner cap.
Before cleaning, make sure all controls are off and
1
Burner Rotation
The right side burners can be rotated 180° to reduce the distance
between the front and back burners. This permits better heat
distribution when using oblong pans or griddles.
To Rotate Burners:
Make sure burners are cool before beginning rotation.
1.
Remove right side grates and burner caps.
2.
Lift burners from cooktop, as shown.
3.
Rotate burners 180°, as shown.
4.
2
1. Incorrect
2. Correct
Turn on the burner. If the burner does not light, check cap
5.
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
Replace burners, with large hole over gas tube opening, and
5.
small hole over the ignitor. See “Sealed Surface Burners”
section for burner parts descriptions. Push burner down,
flush with cooktop.
Replace burner caps and grates.
6.
7
Home Canning
When canning for long periods, alternate the use of surface
cooking areas, elements or surface burners between batches.
This allows time for the most recently used areas to cool.
■ Center the canner on the grate or largest surface cooking
area or element. Canners should not extend more than 1 in.
(2.5 cm) outside the cooking area.
■ Do not place canner on two surface cooking areas, elements
or surface burners at the same time.
■ On ceramic glass models, only use flat-bottomed canners.
■ On coil element models, the installation of a Canning Unit Kit
is recommended. If not installed, the life of the coil element
will be shortened. See “Assistance or Service” for ordering
instructions.
■ For more information, contact your local U.S. Government
Agricultural Department Extension Office. In Canada, contact
Agriculture Canada. Companies that manufacture home
canning products can also offer assistance.
Use the following chart as a guide for cookware material
characteristics.
COOKWARECHARACTERISTICS
*Aluminum
■ Heats quickly and evenly.
■ Suitable for all types of cooking.
■ Medium or heavy thickness is best for
most cooking tasks.
Cast iron
Ceramic or
Ceramic glass
■ Heats slowly and evenly.
■ Good for browning and frying.
■ Maintains heat for slow cooking.
■ Rough surfaces may scratch cooktop.
■ Follow manufacturer’s instructions.
■ Rough surfaces may scratch cooktop.
■ Heats slowly, but unevenly.
■ Ideal results on low to medium heat
settings.
Cookware
IMPORTANT: Never leave empty cookware on a hot surface
cooking area, element or surface burner.
Ideal cookware should have a flat bottom, straight sides, a wellfitting lid and the material should be of medium-to-heavy
thickness.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A non-stick finish has
the same characteristics as its base material. For example,
aluminum cookware with a non-stick finish will take on the
properties of aluminum.
*Copper
Earthenware
Porcelain
■ Heats very quickly and evenly.
■ Follow manufacturer’s instructions.
■ Use on low heat settings.
■ See stainless steel or cast iron.
enamel-onsteel or cast
iron
Stainless steel
■ Heats quickly, but unevenly.
■ A core or base of aluminum or copper
on stainless steel provides even
heating.
*Aluminum and copper may be used as a core or base in
cookware. When used as a base it can leave permanent marks
on the cooktop or grates.
8
ELECTRONIC OVEN CONTROL
Indicator Lights
1.
Electronic Display
2.
Off/Cancel pad
3.
1
9
4.
5.
6.
2
7
Start/Enter pad
Clock/Timer pad
Start Time/Cook Time pad (on some
models)
Display
When power is first supplied to the appliance, “PF” will appear on
the display. Press OFF to clear.
Any other time “PF” appears, a power failure has occurred. Press
OFF and reset the Clock if needed.
When the oven is in use, the display shows preheat time and the
temperature and oven setting.
When the oven is not in use, the display shows the time of day.
When using COOK TIME (on some models,) the display will show
either hours and minutes, or minutes and seconds.
Oven Indicator Lights
The indicator lights are located to the left of, below, and within
the display. The indicator lights light up or flash when the oven is
in one of the following modes: BAKE, BROIL, HEAT, START?, ON,
TIMER, COOK TIME/TIMED cooking (on some models,) and
START TIME/DELAY cooking (on some models.)
Start/Enter
The START/ENTER pad begins any oven function except the
Timer. If not pressed within 5 seconds after pressing a function
pad, the “START?”indicator light will flash as a reminder. If not
pressed within 5 minutes after pressing a function pad, the oven
display will return to the time of day mode and the programmed
function will be cancelled.
Off/Cancel
The OFF pad stops any function except the Clock, Timer and
Control Lock.
68
345
Temperature/Time pad
7.
Custom Broil pad
8.
Bake pad
9.
Clock
This is a 12 hour clock and does not show a.m. or p.m.
To S et:
Before setting, make sure the oven and Timer are off.
Press CLOCK.
1.
Press the “up” or “down” arrow pads to set the time of day.
2.
Press CLOCK or START.
3.
Timer
The Timer can be set in hours or minutes up to 12 hours and 59
minutes, and counts down the set time either in hours and
minutes, or in minutes and seconds. The Timer does not start or
stop the oven.
To S et:
Press TIMER.
1.
The Timer indicator light will light up.
Press the “up” or “down” arrow pads to set the length of time
2.
to cook.
Press START/ENTER.
3.
When the Timer has finished counting down, four one-second
tones will sound.
To display the time of day at any time during timed cooking,
press CLOCK once
Press TIMER twice at any time during Timer operation to
4.
cancel the Timer.
The time can be reset during the countdown by repeating the
above steps.
9
Control Lock
The Control Lock shuts down the control panel pads to prevent
unintended use of the oven.
When the control is locked, only the CLOCK and TIMER pads
will function.
To Lock/Unlock Control: Before locking, make sure the oven
and Timer are off. Press and hold START/ENTER for 5 seconds. A
single tone will sound and “LOC” will appear on the display.
“LOC” will also appear whenever any command pad is pressed
while the control is locked. Repeat to unlock, and “LOC” will
disappear from the display.
Oven Temperature Control
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door and element or
burner cycling may give incorrect readings.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted. It can be changed in Fahrenheit or
Celsius.
A minus sign means the oven will be cooler by the displayed
amount. No sign means the oven will be warmer by the displayed
amount. Use the following chart as a guide.
ADJUSTMENT °F
(ADJUSTMENT °C)
5° to 10°F (3° to 6°C)...a little more
15° to 20°F (9° to 12°C)...moderately more
25° to 35°F (15° to 21°C)...much more
COOKS FOOD
OVEN USE
Aluminum Foil
IMPORTANT: Do not line the oven bottom with any type of foil,
liners or cookware because permanent damage will occur to the
oven bottom finish.
■
Do not block or cover the oven bottom vents.
■
Do not cover entire rack with foil because air must be able to
move freely for best cooking results.
■
To catch spills, place foil on rack below dish. Make sure foil is
at least 1 in. (2.5 cm) larger than the dish and that it is turned
up at the edges.
Positioning Racks and Bakeware
IMPORTANT: Never place food or bakeware directly on the oven
door or bottom. Permanent damage will occur to the porcelain
finish.
RACKS
Position racks before turning the oven on. Do not move racks
with bakeware on them. Make sure racks are level. For best
performance, cook on one rack. Place the rack so the top of food
will be centered in the oven. To move a rack, pull it out to the stop
position, raise the front edge, then lift out.
FOODRACK POSITION
Frozen pies, large roasts, turkeys,
angel food cakes
1 or 2
-5° to -10°F (-3° to -6°C)...a little less
-15° to -20°F (-9° to -12°C)...moderately less
-25° to -35°F (-15° to -21°C)...much less
To Adjust Oven Temperature Calibration:
1. Press and hold BAKE for 5 seconds until the oven display
shows the current calibration, for example “00.”
2. Press the TEMP (▲) or (▼) pads to increase or to decrease
the temperature in 10°F (6°C) amounts. the adjustment can
be set between 30°F (18°C) and -30°F (-18°C).
3. Press START/ENTER.
Bundt cakes, most quick breads, yeast
breads, casseroles, meats
Cookies, biscuits, muffins, cakes, non
frozen pies
2
2 or 3
BAKEWARE
To cook food evenly, hot air must be able to circulate. Allow 2 in.
(5 cm) of space around bakeware and oven walls. Use the
following chart as a guide.
NUMBER OF
PA N ( S )
1Center of rack.
2Side by side or slightly staggered.
3 or 4Opposite corners on each rack. Make sure
POSITION ON RACK
that no bakeware piece is directly over
another.
10
Bakeware
The bakeware material affects cooking results. Follow
manufacturer’s recommendations and use the bakeware size
recommended in the recipe. Use the following chart as a guide.
BAKEWARE/
RESULTS
Light colored
aluminum
■
Light golden
crusts
■
Even browning
Dark aluminum
and other
bakeware with
dark, dull and/or
non-stick finish
■
Brown, crisp
crusts
Insulated cookie
sheets or baking
pans
■
Little or no
bottom
browning
Stainless steel
■
Light, golden
crusts
■
Uneven
browning
Stoneware
■
Crisp crusts
■
■
■
■
■
■
■
■
■
RECOMMENDATIONS
Use temperature and time
recommended in recipe.
May need to reduce baking
temperatures 25°F (15°C).
Use suggested baking time.
For pies, breads and casseroles, use
temperature recommended in
recipe.
Place rack in center of oven.
Place in the bottom third of oven.
May need to increase baking time.
May need to increase baking time.
Follow manufacturer’s instructions.
Baking and Roasting
IMPORTANT: Never light the oven burner during a power failure.
Never place food or cookware directly on the oven door or the
oven bottom. When using the oven for the first time, it is
necessary to turn any one of the surface burners on first to
release air from the gas lines.
Before baking and roasting, position racks according to the
“Positioning Racks” section.
To Bake or Roast:
1. Press BAKE.
Press TEMP (▲) or (▼) to set a temperature other than 350°F
(177°C) in 5ºF (3°C) amounts. The bake range can be set
between 170°F (77°C) and 500°F (260°C.)
2. Press START/ENTER.
The temperature can be changed at any time after this step
by pressing the TEMP (▲) or (▼) pad. START/ENTER does
not need to be pressed again. If baking/roasting while the
Timer is counting down, the set baking/roasting temperature
can be displayed for 5 seconds by pressing BAKE.
3. Press OFF/CANCEL when finished.
Preheating
After START/ENTER is pressed, the oven will enter a timed
preheat conditioning cycle. The HEAT, BAKE, and ON indicator
lights will light up. The Electronic Oven Control automatically
selects the conditioning cycle time based on the oven
temperature selected. The conditioning cycle time will not
change if the temperature is reset before the cycle countdown
ends. The preheat conditioning cycle is complete and the oven is
ready to use when a 1-second tone sounds, the cycle countdown
ends, and the set temperature is displayed.
Preheat temperatures are affected by varying factors such as
room temperature and peak energy usage times. It is normal for
the temperature showing on the display and the actual oven
temperature to differ.
Waiting an additional ten minutes after the preheat conditioning
time ends to put food in the oven is suggested when baking
foods with leavening ingredients, such as yeast, baking powder,
baking soda and eggs.
Ovenproof
glassware,
■
May need to reduce baking
temperatures 25°F (15°C).
ceramic glass or
ceramic
■
Brown, crisp
crusts
Oven Vent
1
1. Oven Vent
The oven vent releases hot air and moisture from the oven, and
should not be blocked or covered. Doing so will cause poor air
circulation, affecting cooking and cleaning results. Never set
plastics, paper or other items that could melt or burn near the
oven vent.
Broiling and Custom Broiling
BROILER
The broiler is located below the oven door. The broiler pan and
grid roll out for easy access. Always broil with the broiler and
oven doors closed.
■
Do not step on or apply weight to the broiler door while it is
open.
■
Do not preheat broiler before use. Completely close broiler
door during broiling.
■
Do not use broiler drawer for storage.
■
Use only the broiler pan and grid provided with the appliance.
It is designed to drain juices and help prevent spatter and
smoke.
■
For proper draining, do not cover the grid with foil. The
bottom of the pan may be lined with aluminum foil for easier
cleaning.
■
Trim excess fat to reduce spattering. Slit the remaining fat on
the edges to prevent curling.
■
Pull out oven rack to stop position before turning or removing
food. Use tongs to turn food to avoid the loss of juices. Very
thin cuts of fish, poultry or meat may not need to be turned.
■
After broiling, remove the pan from the oven when removing
the food. Drippings will bake on the pan if left in the heated
oven, making cleaning more difficult.
11
To Broil:
Open the broiler door and roll out the broiler pan and grid.
1.
Place the broiler pan and grid so grease can drain down into
2.
the lower part of the broiler pan.
Place food on broiler pan. Then place the pan on the broiler
3.
rack and close the broiler door.
Press CUSTOM BROIL.
4.
The BROIL indicator light will light up.
Press START/ENTER.
5.
The ON and HEAT indicator lights will light up. The
temperature setting can be changed at any time during
broiling. If broiling while the Timer is counting down, the set
broiling temperature can be displayed for 5 seconds by
pressing CUSTOM BROIL.
Press OFF/CANCEL when finished broiling.
6.
To CUSTOM BROIL:
Changing the temperature while custom broiling allows more
precise control when cooking. The lower the temperature, the
slower the cooking. Thicker cuts and unevenly shaped pieces of
meat, fish and poultry may cook better at lower broiling
temperatures. If food is cooking too quickly, the broiling
temperature can be lowered by pressing the TEMP (▼) pad.
Press CUSTOM BROIL.
1.
Press the TEMP (▲) or (▼) pads to set a temperature between
2.
300°F (149°C) and 525°F (273°C).
Press START/ENTER.
3.
Press OFF/CANCEL when finished custom broiling.
4.
BROILING CHART
For best results, broiler pan should be rotated the same time the
food is turned. Times are guidelines only and may need to be
adjusted for individual foods and tastes.
COOK
FOOD
Chicken, bone-in pieces,
boneless breasts
Fish Fillets ¹|₂-³|₄ in. (1.25-1.8 cm) thick7-83-4
Frankfurters5-62-3
*Ground meat patties ³|₄ in. (1.8 cm)
thick, well done11-136-7
TIME
minutes
SIDE 1 SIDE 2
15-17
11-13
15-17
11-13
Timed Cooking
(on some models)
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour
before or after cooking.
Doing so can result in food poisoning or
sickness.
The electronic MEALTIMER™ control (on some models) allows
the oven to be set to turn on at a certain time of day, cook for a
set length of time, and/or shut off automatically. Delay start
should not be used for food such as breads and cakes because
they may not bake properly.
To Set a Cook Time (on some models):
Place the oven racks where needed and place food on the
1.
appropriate rack. (See “Positioning Racks and Bakeware”
section.)
Press BAKE.
2.
The BAKE indicator light will light up.
Set the temperature (optional).
3.
Press the TEMP (▲) or (▼) pads to raise or lower the
temperature in 5°F (3°C) increments from the default setting
of 350°F (177°C).
Press COOK TIME.
4.
The COOK TIME indicator light will light up.
Set the cook time.
5.
Press the (▲) or (▼) pads until the correct cook time shows
on the display.
Press START/ENTER.
6.
Temperature or time settings can be changed at any time
after this step, by repeating steps 3 or 5.
The display will show the baking/roasting countdown time in
hours and minutes, or in minutes and seconds, depending on
the length of the cook time.
The MEALTIMER control setting may be cancelled, and the
oven turned off at any time by pressing OFF/CANCEL.
When baking/roasting is complete, the oven will automatically
7.
turn itself off, and 4 one-second tones will sound.
Ham slice, precooked ¹|₂ in. (1.25 cm)
thick6-83-4
Lamb chops 1 in. (2.5 cm) thick14-178-9
Pork chops 1 in. (2.5 cm) thick19-219-10
Steak 1 in. (2.5 cm) thick, medium rare,
medium
well done
* Place up to 9 patties, equally spaced, on broiler grid.
10-12
12-14
16-17
12
5-6
6-7
8-9
To Set a Delayed Start Cook Time (on some models):
Before setting, make sure the clock is set to the correct time of
day. See “Clock” section.
Place the oven racks where needed and place food on the
1.
appropriate rack. (See “Positioning Racks and Bakeware”
section.)
Press BAKE.
2.
The BAKE indicator light will light up.
Set the temperature (optional).
3.
Press the TEMP (▲) or (▼) pads to raise or lower the
temperature in 5°F (3°C) increments from the default setting
of 350°F (177°C).
Press COOK TIME.
4.
The COOK TIME indicator light will light up.
Set the cook time.
5.
Press the (▲) or (▼) pads until the correct cook time shows
on the display.
Press START TIME.
6.
The START TIME/DELAY indicator light will light up.
Set the start time.
7.
Press the TIME (▲) or (▼) pads until the correct start time
shows on the display.
Press START/ENTER.
8.
The temperature or time settings may be changed at any time
after this step by repeating steps 3 through 8.
The MEALTIMER™ delayed start cook time control setting
may be cancelled, and the oven turned off at any time by
pressing OFF/CANCEL.
When the start time is reached, a one-second tone will
9.
sound. The display will show the baking/roasting countdown
time in hours and minutes, or in minutes and seconds,
depending on the length of the cook time.
When baking/roasting is complete, the oven will automatically
10.
turn itself off, and 4 one-second tones will sound.
RANGE CARE
General Cleaning
IMPORTANT:
the oven and cooktop are cool. Always follow label instructions
on cleaning products. Do not wipe down any of the inside
surfaces until the oven has completely cooled down. Applying a
cool damp cloth to the inner door glass before it has cooled
completely could result in the glass breaking.
Soap, water and a soft cloth or sponge are suggested first unless
otherwise noted.
COOKTOP CONTROLS
Do not use steel wool, abrasive cleansers or oven cleaner.
Do not soak knobs.
When replacing knobs, make sure knobs are in the OFF position.
On some models, do not remove seals under knobs.
■
Soap and water or dishwasher:
Pull knobs straight away from control panel to remove.
CONTROL PANEL
Do not use abrasive cleaners, steel-wool pads, gritty wash cloths
or some paper towels. Damage may occur.
■
Glass cleaner and soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
EXTERIOR PORCELAIN ENAMEL SURFACES
(on some models)
Before cleaning, make sure all controls are off and
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire appliance is cool. These spills
may affect the finish.
■
Glass cleaner, mild liquid cleaner or non-abrasive scrubbing
pad:
Gently clean around the model and serial number plate
because scrubbing may remove numbers.
PORCELAIN-COATED GRATES AND CAPS
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the cooktop, grates and caps are cool.
These spills may affect the finish.
To avoid chipping, do not bang grates and caps against each
other or hard surfaces such as cast iron cookware.
Do not reassemble caps on burners while wet.
Do not clean in dishwasher.
■
Non-abrasive plastic scrubbing pad and mildly abrasive
cleanser:
Clean as soon as cooktop, grates and caps are cool.
13
SURFACE BURNERS
Sealed Burner models
See “Sealed Surface Burners” section.
Open Burner models
See “Surface Burners” section.
BROILER PAN AND GRID
Do not clean in the Self-Cleaning cycle.
■ Mildly abrasive cleanser:
Scrub with wet scouring pad.
■ Solution of ¹|₂ cup (125 mL) ammonia to 1 gallon (3.75 L)
water:
Soak for 20 minutes, then scrub with scouring or steel wool
pad.
■ Oven cleaner:
Follow product label instructions.
Porcelain enamel only, not chrome
■ Dishwasher
OVEN CAVITY
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain and staining, etching,
pitting or faint white spots can result.
On some models, the oven door can be removed. See “Oven
Door” first.
■ Steel wool pad
■ Oven cleaner:
Follow product label instructions. Do not let cleaner contact
gasket, thermostat or exterior surfaces. Line the floor with
newspaper.
Oven Light
The oven light is a standard 40-watt appliance bulb. It will come
on when the oven door is open. When the oven door is closed,
press the manual oven light switch on the backguard to turn on
and off.
Before replacing, make sure the oven and cooktop are cool and
the control knobs are off.
To Replace:
1. Unplug range or disconnect power.
2. Turn bulb counterclockwise to remove from socket.
3. Replace bulb.
4. Plug in range or reconnect power.
Oven Door
For normal range use, it is not suggested to remove the oven
door. However, if necessary, follow these instructions. The oven
door is heavy.
To Remove:
1. Open the oven door. Insert hinge pins, included with your
range, into both hinge hangers. Do not remove the pins while
the door is removed from the range.
2. Grasp the door on the sides with your fingers on the front of
the door and your thumbs on the inside surface.
OVEN DOOR GLASS
■ Glass cleaner and paper towels or non-abrasive plastic
scrubbing pad
OVEN AND ROASTING RACK
■ Steel wool pad
(on some models)
3. Pull door straight up, then toward you. Do not remove hinge
pins until the door is replaced on the range.
14
To Replace:
Grasp the door on the sides with your fingers on the front of
1.
the door and your thumbs on the inside surface.
Hold oven door so that the top edge of each door slot is
2.
horizontal. Insert door hinge into the hinge slots.
Tilt top of door toward range. Insert bottom door hinge notch
3.
down onto front frame edge.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the
cost of an unnecessary service call.
Nothing will operate
■
Is the power outlet properly wired and polarized?
Try another outlet to check for proper wiring and polarity.
■
Is the power supply cord unplugged?
Plug into a properly grounded 3 prong outlet.
■
Has a household fuse been blown or has the circuit
breaker been tripped?
Replace the fuse or reset the circuit.
■
Is the main or regulator gas shutoff valve in the off
position?
See Installation Instructions.
■
Is the range properly connected to the gas supply?
Contact a trained repair specialist or see Installation
Instructions.
Surface burners will not operate
Open the door completely and remove the hinge pins. Save
4.
hinge pins for future use.
Close the door slowly to assure door side panel clearance
5.
and proper hinge engagement.
Removing the Oven Bottom
The oven bottom can be removed for standard cleaning of the
oven.
Before cleaning, make sure the oven is completely cool.
To Remove:
Remove the oven racks.
1.
Place fingers in the slots in the bottom panel.
2.
1. Lip
Lift the rear of the panel up and back.
3.
The lip at the front of the panel should clear the front frame of
the oven cavity.
Lift the bottom up and out.
4.
To Replace:
Reverse the steps above.
■
Is this the first time the surface burners have been used?
Turn on any one of the surface burner knobs to release air
from the gas lines.
■
Is the control knob set correctly?
Push in knob before turning to a setting.
■
Are the burner ports clogged?
On sealed burner models, see “Sealed Surface Burners”
section.
On open burner models, see “Surface Burners” section.
Surface burner flames are uneven, yellow and/or noisy
■
Are the burner ports clogged?
On sealed burner models, see “Sealed Surface Burners”
section.
On open burner models, see “Surface Burners” section.
■
On models with caps, are the burner caps positioned
properly?
See “Sealed Surface Burners” section.
■
Is the burner damaged?
On models with caps, look for warped cap. Place cap, flat
side-down, on a flat surface. If cap wobbles noticeably, it is
warped. Place cap on different burner for further check of
warping. Replace warped cap. Contact a trained repair
specialist if the condition does not improve.
■
Is the air/gas mixture correct?
Contact a designated service technician to check the air/gas
mixture, or see the Installation Instructions.
■
Is propane gas being used?
The appliance may have been converted improperly.
Contact a trained repair specialist.
Surface burner makes popping noises
■
Is the burner wet?
Let it dry.
15
Cookware not level on cooktop
Display shows messages
Is the range level?
■
Level the range. (See the Installation Instructions.)
Is the proper cookware being used?
■
Use cookware with a flat bottom. (See “Cookware” section.)
Excessive heat around cookware on cooktop
Is the cookware the proper size?
■
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than 1 in. (2.5 cm) outside the cooking area.
Are the right side surface burners rotated toward each
■
other?
See "Burner Rotation" section.
Oven will not operate
Is the power outlet properly wired and polarized?
■
Try another outlet to check for proper wiring and polarity.
Is this the first time the oven has been used?
■
Turn any one of the surface burner knobs on to release air
from the gas lines.
Is the electronic oven control set correctly?
■
See “Electronic Oven Control” section.
On some models, is the Oven Lockout set?
■
See “Oven Lockout” section.
Is the main or regulator gas shutoff in the off position?
■
Contact a designated service technician or see the
Installation Instructions.
Oven makes muffled ticking noise when in use
Is the display showing “PF”?
■
There has been a power failure. Press OFF/CANCEL to clear
the display. Reset the clock, if needed. See “Clock” section.
Is the display showing “F” followed by a number?
■
Press OFF/CANCEL to clear the display. If an "F" code
appears again, contact a trained repair specialist.
Has a delay start been set?
■
See “Timed Cooking” section.
Cooktop cooking results not what expected
Is the proper cookware being used?
■
See “Cookware” section.
Is the control knob set to the proper heat level?
■
See “Cooktop Controls” section.
Baking results not what expected
Was the oven preheated?
■
Wait for oven to preheat before placing food in oven.
Are the racks positioned properly?
■
See “Positioning Racks and Bakeware” section.
Is there proper air circulation around bakeware?
■
See “Positioning Racks and Bakeware” section.
Is the batter evenly distributed in the pan?
■
Check to make sure batter is level in the pan.
Is the appliance level?
■
Level the appliance. See the Installation Instructions.
Are baked items too brown on the bottom?
■
Decrease oven temperature 15°F to 25°F (5°C to 15°C).
Are crust edges browning early?
■
Use aluminum foil to cover the edge of the crust.
■ This is normal and occurs when the oven burner cycles on
and off to hold the set oven temperature.
Oven burner flames are uneven, yellow, or noisy
Is propane gas being used?
■
The appliance may have been converted improperly. Contact
a trained repair specialist.
Is the air/gas mixture correct?
■
Contact a designated service technician to check the air/gas
mixture or see the Installation Instructions.
Oven temperature too high or too low
Does the oven temperature calibration need adjustment?
■
See “Oven Temperature Control” section.
Slow baking or roasting
Was the oven preheated?
■
Wait for oven to preheat before placing food in oven.
Is there proper air circulation around bakeware?
■
See “Positioning Racks and Bakeware” section.
Is the proper length of time being used?
■
Increase baking or roasting time.
Is the proper temperature set?
■
Increase temperature 25°F (15°C).
Has the oven door been opened while cooking?
■
Oven peeking releases oven heat and can result in longer
cooking times.
Broiler burner fails to light
Is the ignition system broken?
■
Contact a designated service technician to replace it.
Has a household fuse been blown or has the circuit
■
breaker been tripped?
Replace the fuse or reset the circuit.
16
Loading...
+ 36 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.