Whirlpool WRV996FDEH01, WRV986FDEM01, WRV996FDEM01, WRV996FDEE02, WRV996FDEE01 Owner’s Manual

...

REFRIGERATOR USER INSTRUCTIONS

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.whirlpool.com. In Canada, register your refrigerator at www.whirlpool.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the refrigerator compartment.

Model Number___________________________________________ Serial Number____________________________________________

Table of Contents

REFRIGERATOR SAFETY ..............................................................2

Proper Disposal of Your Old Refrigerator ....................................3

INSTALLATION INSTRUCTIONS ...................................................3

Unpack the Refrigerator ...............................................................3

Remove and Replace Refrigerator Doors ....................................4

Remove and Replace Drawer Fronts ...........................................6

Align Doors and Drawers .............................................................8

Location Requirements ..............................................................10

Electrical Requirements .............................................................11

Water Supply Requirements ......................................................11

Connect the Water Supply .........................................................11

Handle Installation and Removal ...............................................13

Refrigerator Leveling and Door Closing .....................................14

FILTERS AND ACCESSORIES ....................................................15

Water Filtration System ..............................................................15

Install Air Filter (on some models) ..............................................16

Install Produce Preserver

(on some models) .......................................................................17

Accessories ................................................................................17

REFRIGERATOR USE ..................................................................17

Opening and Closing Doors .......................................................17

Using the Controls .....................................................................18

Refrigerator Features .................................................................20

Water and Ice Dispensers ..........................................................22

Ice Maker and Ice Storage Bin

(on some models) .......................................................................25

REFRIGERATOR CARE ...............................................................26

Cleaning .....................................................................................26

Lights ..........................................................................................27

Vacation and Moving Care .........................................................27

TROUBLESHOOTING ..................................................................28

PERFORMANCE DATA SHEET ...................................................33

W10730915C

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

WARNING:

■ Plug into a grounded (earthed) outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Do not store or use petrol, flammable liquids or gas in the

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

vicinity of this or other electrical appliances. The fumes can

cause fires or explosions.

■ Do not store explosive substances such as aerosol cans

with a flammable propellant in this refrigerator.

■ Do not use or place electrical devices inside the refrigerator

compartments if they are not of the type expressly

authorized by the manufacture.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ A qualified service technician must install the water line and

ice maker.

■ Connect to a potable water supply only.

Use a sturdy glass when dispensing ice (on some models).

■

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

■ To avoid the risk of children becoming trapped and

suffocating, do not allow them to play or hide inside the

refrigerator.

■ If the power supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly qualified

person.

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

WARNING

Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous –even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

■ Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”

■ Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the oor with cardboard or hardboard to avoid oor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as oor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in “Refrigerator Care.”

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATION

INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your ngers. Wipe with warm water and dry.

Remove and Replace Refrigerator Doors

NOTE: Measure the width of your door opening to see whether or not you need to remove the refrigerator doors to move the refrigerator into your home. If door removal is necessary, see the following instructions.

IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator control OFF. Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors. TOOLS NEEDED: 3/16" hex key and a #2 Phillips screwdriver

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Door Removal and Replacement

Water Dispenser

Tubing Connection

A. Outer Ring

Wiring Plug

Door Removal

Top Right Hinge

A. 3/16" Internal Hex-Head Screws B. Hinge Cover Screw C. Top Hinge Cover D. Top Hinge

Door at 90° Angle

to Cabinet

Top Left Hinge

A. 3/16" Internal Hex-Head Screws B. Ground Wire (Do Not Remove.) C. Do Not Remove Screws

90°

Remove Refrigerator Doors

WARNING

Electrical Shock Hazard Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

Remove Right-Hand Refrigerator Door

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet. NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Using a Phillips screwdriver, remove the cover from the top

hinge.

4. Using the 3/16" hex key wrench, remove the two internal hex-

head screws from the top hinge, and set aside. NOTE: Do not remove the two locator screws. These screws

will help you align the hinge when you replace the door.

Remove Left-Hand Refrigerator Door IMPORTANT: The tubing and wiring for the water dispenser run

through the left-hand door hinge, so they must be disconnected before removing the door.

1. Using a Phillips screwdriver, remove the cover from the top

hinge.

A. Top hinge cover screw B. Top hinge cover

2. Disconnect the water dispenser tubing located on top of the

door hinge. Firmly pulling up on the clasp, and then pull the tubing out of the tting.

NOTE: The water dispenser tubing remains attached to the left-hand refrigerator door.

3. Disconnect the wiring plug located on top of the door hinge.

■ Grasp each side of the wiring plug. With your left thumb,

A. Top hinge cover screw B. Top hinge cover

C. 3/16" Internal hex-head screws D. Top hinge

press down to release the catch and pull the sections of the plug apart.

NOTE: Do not remove the green, ground wire. It should remain attached to the door hinge.

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

5. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

4. Using the 3/16" hex key wrench, remove the two internal hex-

head screws from the top hinge and set aside.

NOTES:

■ Provide additional support for the refrigerator door while the

hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

■ Do not remove the two locator screws. These screws will help

you align the hinge when you replace the door.

A B

A. 3/16" Internal hex-head screws

B. Ground wire (Do not remove)

C. Locator screws (Do not remove)

5. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door. NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a doorway.

■ Only if necessary, use a driver with a #2 square bit tip to

remove the bottom hinges and a 3/8" nut driver to remove the brake feet screws.

Remove and Replace Drawer Fronts

Depending on the width of your door opening, it may be necessary to remove the drawer fronts to move the refrigerator into your home.

IMPORTANT:

■ If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator control off, and unplug the refrigerator or disconnect power. Remove food from the drawers.

■ Two people may be required to remove and replace the

drawer fronts.

Tools Needed: Flat-blade screwdriver

Refrigerated Drawers

Remove the Drawer Fronts

1. Open the drawer to its full extension. Grasp the sides of the

interior bin, and then lift up and out to remove.

Replace Refrigerator Doors

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the

refrigerator door.

3. Using the two 3/16" internal hex-head screws, fasten the

hinge to the cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the two 3/16" internal hex-head screws, fasten the

hinge to the cabinet. Do not tighten the screws completely.

3. Reconnect the water dispenser tubing. Style 1 - Insert the tubing into the tting until it stops and the

outer ring is touching the face of tting. Style 2 - Insert the tubing rmly into the tting until it stops.

Close the clasp around the tubing. The clasp snaps into place between the tting and the collar.

4. Reconnect the electrical wiring.

■ Push together the two sections of the wiring plug.

Final Steps

1. Completely tighten the four internal hex-head screws (two on the right-hand door hinge and two on the left-hand door hinge).

2. Replace both top hinge covers.

2. Left-hand drawer only: Remove the wiring connection cover.

Press in on the side of the cover to release the tab from the slot, and then pull the cover away from the bracket.

A. Cover tab B. Wiring connection cover

3. Left-hand drawer only: Disconnect the wiring. NOTE: The drawer front of the left-hand refrigerated drawer

is connected to the temperature control by wires running underneath the drawer glide. Before removing the drawer front, the wires must be disconnected.

■ On one side of the wiring connector, insert the screwdriver

blade between the connector tab and the connector to release. Repeat for the opposite side. Pull the wiring connector apart.

4. Remove the drawer front.

■ Push up on the lever at the bottom of the drawer glide

bracket to release the drawer front from the bracket.

■ Lift the drawer front up and off the drawer glide brackets.

3. Left-hand drawer only: Reconnect wiring.

■ Align the two ends of the wiring connector and push them

together until you hear a “click” sound and feel the tabs snap into place on the connector.

■ Gently pull on the wiring connection to ensure the wiring

connection is completely seated. Replace the wiring cover.

NOTE: The wiring connection must be complete for the drawer temperature control to operate.

4. Left-hand drawer only: Replace the wiring connection cover.

5. Replace the drawer bins onto the drawer glides with the rear

side of the bin facing the back of the refrigerator, as shown. IMPORTANT: The Door Ajar alarm will sound if the interior

drawer bins are not replaced correctly. The bins are designed with a specic front and rear. They must be placed into the drawers, as shown, so that the refrigerated drawers will close

and operate properly.

A. Drawer glide bracket B. Release lever

5. Slide the drawer glides back into the refrigerator. Replace the Drawer Fronts

1. Pull out the drawer glides until they are fully extended.

2. Push up on the lever at the bottom of the drawer glide bracket

to open. Insert the drawer front bracket into the drawer glide bracket and release the lever.

NOTE: It helps if one person holds the drawer glides steady while another person aligns the drawer front and connects the brackets.

A. Faces back of refrigerator (insert ﬁrst) B. Faces front of refrigerator

Freezer Drawer

Remove Drawer Front

1. Open the freezer drawer to its full extension.

2. Loosen the two top screws that fasten the drawer front to

the drawer glides. The two screws (one on the left-hand side and one on the right-hand side) are located inside the drawer front.

3. Lift up on the drawer front to release the plastic studs from

the drawer glide bracket slots.

A. Drawer glide bracket slots

4. Slide the drawer glides back into the freezer. Replace Drawer Front

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the two plastic

studs, located at the bottom, inside the drawer front, with the drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady while another person aligns the drawer front and inserts the studs into the slots.

Final Steps

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See “Using the Control(s)” and

“Temperature Controlled Exterior Drawer.”

3. Return all removable parts and the food to the drawers.

Align Doors and Drawers

Once the doors and drawer fronts are replaced on the refrigerator, you may notice that the doors appear angled or that they are no longer level. Both the refrigerator doors and refrigerated drawers are adjustable.

Align Refrigerator Door

Tools Provided: 1/8" hex key

1. Keeping both refrigerator doors closed, pull out the right-hand

refrigerated drawer. Locate the bottom hinge pin of the refrigerator door. The alignment screw is inside the bottom hinge pin.

A B

A. Drawer front screw B. Drawer front plastic stud

3. Replace and tighten the two screws at the top of the drawer

front (one on the left-hand side and one on the right-hand side).

2. Insert the short end of the 1/8" hex key (packed with the Door

3. Continue to turn the alignment screw until the doors are

A. Bottom hinge pin B. Turn to the right to raise.

Handle Installation Instructions) into the bottom hinge pin until it is fully engaged in the alignment screw.

■ To raise the door, turn the hex key to the right.

■ To lower the door, turn the hex key to the left.

aligned.

C. Turn to the left to lower. D. 1/8" Hex key

Align Refrigerated Drawer Fronts

3. Locate the drawer glide brackets (A).

When the drawer fronts are aligned, the width of the vertical space (A) between the refrigerator doors (B) and the drawer fronts (C) is the same thickness, and the drawers appear level.

Aligning the drawer fronts is a two-step process. The rst step is to adjust the drawer fronts up and down. The second step shifts the drawer fronts from side to side. Visually inspect the refrigerator for alignment and adjust the drawer fronts as needed.

Step 1 - Adjust the Drawer Fronts Up/Down IMPORTANT: Each refrigerated drawer can be adjusted up and

down on both the left and the right sides.

A. Drawer glide brackets

4. Insert the Phillips screwdriver into screw (A) and turn counterclockwise to loosen the drawer front.

A B

Tools Needed: Phillips screwdriver

1. With the drawers closed, identify the drawer front that needs

to be raised or lowered.

2. Open the drawer to its full extension. Grasp the sides of the

interior bin, and then lift it up and out to remove.

A. Tightening screw B. Adjusting screw

5. Insert the Phillips screwdriver into screw (B) to adjust the drawer front.

IMPORTANT: The direction you turn screw (B) depends on which side of the drawer you are adjusting.

Left-Hand Side Drawer Glide

■ To raise the drawer front, turn screw (B) clockwise.

■ To lower the drawer front, turn screw (B) counterclockwise.

Right-Hand Side Drawer Glide

5. Reposition the clip (A) onto the glide bracket (B) in the

direction you want to move the drawer front. Make sure that the glide bracket is vertically level.

6. Release the lever (C) to lock the glide bracket into position.

7. Repeat steps 3 through 6 for the other side of the drawer

front. NOTE: Adjust the clip (A) on the top of the second glide

bracket (B) so that it is in the same position as the side you adjusted rst.

8. Close the drawer and visually inspect the gap. Repeat steps 2 though 7 until the drawer fronts are aligned.

■ To raise the drawer front, turn screw (B) counterclockwise.

■ To lower the drawer front, turn screw (B) clockwise.

6. Insert the Phillips screwdriver into screw (A), and turn

clockwise to tighten the drawer front.

7. Close the refrigerated drawer to check the alignment. Repeat

steps 2 through 6 until the drawer fronts are level.

Step 2 - Adjust the Drawer Fronts Side to Side IMPORTANT: Each refrigerated drawer can be adjusted

side to side on both the left and right side.

1. With the drawers closed, identify the drawer that is not

aligned.

2. Open the drawer to its full extension. Grasp the sides of the

interior bin, and then lift it up and out to remove. (See Step 1 for further details.)

3. Locate the drawer glide brackets. (See Step 1 for further

details.)

4. Starting with the glide bracket closest to the vertical gap,

press and hold the release lever (C) up. With your other hand, lift the door clip (A) from the bracket (B).

Final Steps

1. Replace the interior drawer bins. NOTE: The bins must be placed into the drawers correctly so

that the refrigerated drawers will close and operate properly. See “Remove and Replace Drawer Fronts.”

2. Close the refrigerated drawers.

Location Requirements

WARNING

Explosion Hazard

Keep ammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or re.

IMPORTANT: This appliance is intended to be used in household and similar applications such as.

■ Staff kitchen areas in shops, ofces and other working

environments.

■ Farm houses and by clients in hotels, motels and other

residential type environments.

■ Bed and breakfast type environments.

■ Catering and similar non-retail applications.

NOTE: If the manufacturer wants to limit the use of the appliance to less than the above, this has to be clearly stated in the instructions.

To ensure proper ventilation for your refrigerator, allow for a 1/2" (1.25 cm) of space on each side and at the top. Allow for a 1" (2.54 cm) space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a xed wall, leave a 3³⁄4" (9.5 cm) minimum space between the refrigerator and wall to allow the door to swing open.

A. Drawer front clip B. Drawer glide bracket C. Release lever

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

1/2" (1.25 cm)

33/4" (9.5 cm)

Electrical Requirements

WARNING

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualied plumber.

NOTE: If the water pressure is less than what is required, the ow of water from the water dispenser could decrease or ice cubes could be hollow or irregular shaped.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of

a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).

If a reverse osmosis water ltration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

■ Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■ Allow the storage tank on the reverse osmosis system to rell

after heavy use. The tank capacity could be too small to keep up with the requirements of the refrigerator.

NOTE: Faucet-mounted reverse osmosis systems are not recommended.

■ If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse osmosis system. Remove the water lter. See “Water Filtration System.”

If you have questions about your water pressure, call a licensed, qualied plumber.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its nal location, it is important to make sure you have the proper electrical connection.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualied person. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.

Recommended Grounding Method

A 115 V, 60 Hz, AC only 15 or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator and approved accessories be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn off Cooling, and then disconnect the refrigerator from the electrical source. When you have nished, reconnect the refrigerator to the electrical source and turn on Cooling. See “Using the Control(s).”

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■ Connect to potable water supply only.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and ordinances.

■ The gray water tubing on the back of the refrigerator (which

is used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable and will help avoid “off-taste” or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the following part numbers:

W10505928RP (7 ft [2.14 m] jacketed PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP (25 ft [7.62 m] PEX).

■ Install tubing only in areas where temperatures will remain

above freezing.

+ 24 hidden pages