Whirlpool WRS571CIDM00, WRS576FIDB00, WRS576FIDM00, WRS576FIDW00, WRS586FIDE00 Owner’s Manual

...

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING or PROBLEM SOLVER, please visit our website at www.whirlpool.com for additional information. If you still need assistance, call us at 1-800-253-1301. In Canada, visit our website at www.whirlpool.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Table of Contents / Jndice / Table des mati res

REFRIGERATOR SAFETY ............................... 2

Proper Disposal of Your Old Refrigerator ..... 3

INSTALLATION INSTRUCTIONS ................... 3

Unpack the Refrigerator ................................ 3

Door Removal, Leveling and Alignment ....... 4

Handle Installation and Removal .................. 7

Location Requirements ................................. 8

Electrical Requirements ................................ 8

Water Supply Requirements ......................... 8

Connect Water Supply .................................. 9

Install Air Filter ............................................. 11

Install Produce Preserver ............................ 12

REFRIGERATOR USE ................................... 13

Using the Controls ...................................... 13

Convertible Drawer Temperature Control .. 14

Crisper Humidity Control ............................ 14

Water and Ice Dispensers ........................... 14

Ice Maker and Storage Bin ......................... 16

Water Filtration System ............................... 17

REFRIGERATOR CARE ................................. 17

Cleaning ...................................................... 17

Lights ........................................................... 18

Vacation and Moving Care ......................... 19

PROBLEM SOLVER ....................................... 20

ACCESSORIES .............................................. 24

WATER FILTER CERTIFICATIONS .............. 24

PERFORMANCE DATA SHEET .................... 25

WARRANTY .................................................... 26

SEGURIDAD DEL REFRIGERADOR ............ 27

C6mo deshacerse adecuadamente

de su refrigerador viejo ............................... 28

INSTRUCCIONES DE INSTALACION .......... 28

Desempaque el refrigerador ....................... 28

Remoci6n, nivelaci6n y

alineamiento de las puertas ........................ 29

C6mo instalar y remover las manijas .......... 32

Requisitos de ubicaci6n .............................. 33

Requisitos electricos ................................... 33

Requisitos del suministro de agua .............. 34

Conexi6n del suministro de agua ............... 34

Instalaci6n del filtro de aire ......................... 36

Instalaci6n del preservador

de alimentos frescos ................................... 37

USO DE SU REFRIGERADOR ...................... 38

Uso de los controles ................................... 38

Control de temperatura

del caj6n convertible ................................... 40

Control de humedad del

caj6n para verduras .................................... 40

Despachadores de agua y hielo ................. 40

F_brica de hielo y dep6sito ......................... 42

Sistema de filtraci6n de agua ..................... 43

CUlDADO DE SU REFRIGERADOR ............. 43

Limpieza ...................................................... 43

Luces ........................................................... 44

Cuidado durante las

vacaciones y mudanzas .............................. 45

SOLUClON DE PROBLEMAS ....................... 46

ACCESORIOS ................................................ 51 ACCESSOIRES .............................................. 80

HOJA DE DATOS DEL RENDIMIENTO ....... 52 FEUILLE DE DONNEES

GARANTIA ...................................................... 53 SUR LA PERFORMANCE .............................. 81

SECURITE DU REFRIGERATEUR ................ 55

Mise au rebut appropriee

de votre vieux refrig6rateur ......................... 56

INSTRUCTIONS D'INSTALLATION .............. 56

Deballage du refrigerateur .......................... 56

Retrait, reglage de I'aplomb

et alignement des portes ............................ 57

Installation et demontage des poignees ..... 60

Exigences d'emplacement ......................... 61

Specifications electriques ........................... 61

Specifications de I'alimentation en eau ...... 62

Raccordement de la canalisation d'eau ..... 62

Installation du filtre &air .............................. 64

Installation du sachet de

conservation pour produits frais ................. 65

UTILISATION DU REFRIGERATEUR ........... 66

Utilisation des commandes ........................ 66

Commande de temperature

dans le tiroir convertible .............................. 68

Reglage de I'humidite

dans le bac & legumes ................................ 68

Distributeurs d'eau et de glagons ............... 68

Machine &glagons et bac d'entreposage .. 70

Systeme de filtration de I'eau ..................... 71

ENTRETIEN DU REFRIGERATEUR ............. 72

Nettoyage .................................................... 72

Lampes ........................................................ 72

Entretien avant les vacances

ou Iors d'un demenagement ....................... 74

RESOLUTION DE PROBLEMES ................... 75

GARANTIE ...................................................... 82

W10632883A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

[] Plug into a grounded 3 prong outlet. [] Do not remove ground prong.

[] Do not use an adapter. [] Do not use an extension cord.

[] Disconnect power before servicing. [] Replace all parts and panels before operating.

[] Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

[] Use nonflammable cleaner. [] Keep flammable materials and vapors, such as gasoline,

away from refrigerator. [] Use two or more people to move and install refrigerator. [] Disconnect power before installing ice maker (on ice maker

kit ready models only). [] Use a sturdy glass when dispensing ice (on some models).

[] Do not hit the refrigerator glass doors (on some models).

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

Proper Disposal of

Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous, even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoffthe doors.

• Leave the shelves in place so that children may not easily climb inside.

important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refdge ato

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see "Refrigerator Safety."

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

©oo Bemova 0 Leveling and A ignment

Gather the required tools and parts and read all instructions before starting installation. Save these instructions for future reference. IMPORTANT" The graphics on this page are for models with the ice storage bin on the door. On models with the ice storage bin inside

the freezer, the wiring and water dispenser tubing configurations are simpler than what is shown in these graphics. Please read all instructions on the next few pages for more information.

NOTE: Before moving your product into your home, measure the doorway of your home to see whether you need to remove the refrigerator and freezer doors. If door removal is necessary, see the instructions below.

IMPORTANT" Before you begin, turn the refrigerator control OFF or turn cooling off. Unplug refrigerator or disconnect power. Remove food, the ice storage bin (on some models), and any adjustable door or utility bins from doors.

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

Wiring Connection

A B C D E F

A. P-clamp D. Wiring Clip B. Routing E. Grommets

Plate F. Wiring

C. Electrical Plugs

Housing

Water Dispenser Tubing Connection

(Style 1)

Top Left Hinge

A. Do Not Remove Screws.

Door Removal

Top Right Hinge

A. Do Not Remove Screws.

Bottom Hinges

(Left and Right)

Leveling

A. Face of Fitting

Water Dispenser Tubing Connection (Style 2)

A. Bottom Hinge

B. Leveler Bracket C. Leveling Foot

Door Alignment

(Bottom Right Hinge)

Lower •

A. Alignment Screw

TOOLS NEEDED: Bubble level, Phillips screwdriver, 3/le"hex key, 1/4"hex-head socket wrench, 1/4"and %e" open-ended wrenches or adjustable

wrench, internal star drive or 3/8"hex-head socket wrench

Remove the Doors

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

Unplug refrigerator or disconnect power.

Open both doors to 90°. Remove the base grille by removing the two screws, then pulling out on the outside corners. See

Graphic 1.

NOTE: The doors must only be opened to 90°. If they are opened all the way, the base grille will not come off.

Disconnect the water tubing, located behind the base grille on the freezer door side. The dispenser tubing runs through the

door hinge, and must be disconnected in order to remove the door.

NOTE: On models with the ice storage bin on the door, there are two water tubing connections, as shown. On models with

the ice storage bin inside the freezer, there is only one water tubing connection.

• Style 1: Press the colored outer ring against the face of fitting and pull the water tubing free. See Graphic 2A.

NOTE: Keep the water tubing connector attached to the tube that runs underneath the freezer. The door cannot be

removed if the connector is still attached to the tube that runs through the door hinge.

Style 2: Firmly pull on the clasp to release the tube, then pull the water tubing free. See Graphic 2B.

NOTE: Keep the clasp attached to the tube that runs underneath the freezer.

Disconnect the wiring, located behind the base grille on the freezer door side. See Graphic 3.

On models with the ice storage bin on the door: NOTE: There are two wiring bundles that run underneath the

freezer - a large bundle with a large grommet and two white plugs at the end, and a small bundle with a small grommet

and one yellow plug at the end.

• Remove the P-clamp using a 1/4"hex-head socket wrench. Remove the small wiring bundle from the P-clamp.

• Remove the wiring clip using a 1/4"hex-head socket wrench.

Pull the electrical housing out from under the refrigerator. Disconnect the wiring plugs from the housing.

Gently pull the large wiring bundle (with two white plugs) through the routing plate.

On models with the ice storage bin inside the freezer:

NOTE: The wiring configuration is simpler than what is shown in Graphic 3. There is only one wiring bundle with one wiring

plug, and there is not a routing plate.

• Remove the wiring clip using a 1/4"hex-head socket wrench.

• Pull the electrical housing out from under the refrigerator.

Disconnect the wiring plug from the housing.

Close both doors and keep them closed until you are ready to lift them free from the cabinet.

Use a 3Ae"hex key to remove the top left hinge screws as shown. See Graphic 4.

IMPORTANT: Do not remove either screw A.

Excessive Weight Hazard

Use two or more people to lift the freezer door.

Failure to do so can result in back or other injury.

Lift freezer door straight up off bottom hinge. See Graphic 5. The water tubing and wiring remain attached to the freezer door and pull through the bottom left hinge.

NOTE: This may require two people - one to lift the door and another to feed the water tubing and wiring through the hinge.

On models with the ice storage bin on the door:

Be sure the hole in the hinge is clear of obstructions, then

gently pull one water tube through the hinge. (Avoid

kinking the tube.) Next, gently pull the other water tube through the hinge, again avoiding kinks. Finally, gently pull the wiring bundle (including the grommet and wiring plugs) through the hinge.

models with the ice storage bin inside the freezer:

Be sure the hole in the hinge is clear of obstructions, then gently pull the water tube through the hinge. (Avoid kinking the tube.) Next, gently pull the wiring bundle (including the grommet and wiring plug) through the hinge.

IMPORTANT: Rest the door on its side on a soft, clean surface, such as a towel, blanket or piece of cardboard. This

will help avoid damaging the door, water tubing and wiring.

Use a 3Ae"hex key to remove the top right hinge screws as shown. See Graphic 6.

IMPORTANT: Do not remove either screw A.

Lift the refrigerator door straight up off bottom hinge. IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This will help avoid damaging the door.

10.

It may not be necessary to remove the bottom hinges to move the refrigerator through a doorway. Both bottom hinges have

similar construction.

• If necessary, use an internal star drive or a 3/8"hex-head socket wrench to remove the bottom hinges. See

Graphic 7.

IMPORTANT: The leveler brackets are mounted behind

the hinges. If you remove the hinges, make sure that the

leveler brackets are replaced when reinstalling the hinges.

Replace the Doors and Hinges

Replace both bottom hinges, if removed. Make sure that the leveler brackets are assembled behind the hinges. Tighten

screws. IMPORTANT: When the screws are tightened properly, there

should not be any gaps between the refrigerator, leveler bracket and hinge.

Excessive Weight Hazard

Use two or more people to lift the freezer door. Failure to do so can result in back or other injury.

Before replacing the freezer door on the bottom left hinge, feed the wiring and water tubing through the hinge.

On models with the ice storage bin on the door:

• Feed the small wiring bundle through the hinge. Assistance may be needed.

IMPORTANT: Do not feed the large wiring bundle through the hinge. This bundle is intended to run directly from the door to the connections beneath the freezer. Forcing the large bundle through the hinge may damage the door and/or the wiring, and will keep the door from closing properly.

Feed both water tubes through the bottom left hinge, then replace the freezer door on the hinge. Assistance may be

needed.

On models with the ice storage bin inside the freezer:

• Feed the wiring bundle through the hinge. Assistance may be needed.

• Feed the water tube through the bottom left hinge, then replace the freezer door on the hinge. Assistance may be

needed.

NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.

3. Align and replace the top left hinge as shown. See Graphic 4. Tighten screws.

4. Reconnect water tubing and wiring. IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

On models with the ice storage bin on the door:

Water Connection Style 1: Push the larger %e" (7.94 mm)

water tube into the blue fitting until it stops, then push the smaller 1/4"(6.35 ram) water tube into the green fitting until it stops. See Graphic 2A.

Water Connection Style 2: Push the black water tube with the blue tip into the blue fitting until it stops. Close the clasp around the tubing, making sure it snaps into place. Repeat this process to connect the red-tipped black water tube and the red fitting. See Graphic 2B.

Reinstall the P-clamp around the small wiring bundle (with one yellow plug), then replace the P-clamp on the top screw hole of the routing plate. See Graphic 3.

Gently route the large wiring bundle (with two white plugs) through the hole in the routing plate, so that the wiring runs behind the right side of the routing plate. See

Graphic 3.

NOTE: The large wiring bundle should always remain below the small wiring bundle.

Reconnect the wiring plugs to the electrical housing, then

push the housing back under the refrigerator. Align the left hole in the front lip of the housing with the right hole in the refrigerator's base crossbar. See Graphic 3.

Reinstall the wiring clip over the grommets. First install the smaller grommet into the top of the clip, then install the

larger grommet into the bottom of the clip (closest to the screw hole). See Graphic 3.

Align the clip's screw hole with the left hole in the electrical housing and the right hole in the crossbar, and screw in the clip using a single screw. Tighten screw. See

Graphic 3.

IMPORTANT: Once connected, the wiring bundles should not be taut. Some flexibility is needed to allow the freezer door to open properly.

models with the ice storage bin inside the freezer:

• Water Connection Style 1: Push the water tube into the fitting until it stops. See Graphic 2A.

Water Connection Style 2: Push the water tube into the fitting until it stops. Close the clasp around the tubing,

making sure it snaps into place. See Graphic 2B.

Reconnect the wiring plug to the electrical housing, then push the housing back under the refrigerator. Align the left

hole in the front lip of the housing with the right hole in the refrigerator's base crossbar. See Graphic 3.

• Reinstall the wiring clip over the grommet. See Graphic 3. Align the clip's screw hole with the left hole in the electrical

housing and the right hole in the crossbar, and screw in the clip using a single screw. Tighten screw. See

Graphic 3.

IMPORTANT: Once connected, the wiring should not be

taut. Some flexibility is needed to allow the freezer door to open properly.

5. Replace the refrigerator door by lifting the door onto the bottom right hinge.

6. Align and replace the top right hinge as shown. See Graphic 6. Tighten screws.

7. Replace the ice storage bin (on some models) and any adjustable door or utility bins.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

8. Plug refrigerator into a grounded 3 prong outlet.

Leveling and Door Closing

Your refrigerator has two adjustable front feet -- one on the right and one on the left. In most cases, the refrigerator should be

steady when both feet are touching the floor. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:

1. Move the refrigerator into its final location. If necessary, open both doors to 90° and remove the base grille. See Graphic 1.

2. The two leveling feet are located on the brackets on each side of the product. See Graphic 8.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling feet. This makes it easier to

make adjustments.

3. Use a 1/4"open-ended or adjustable wrench to adjust the leveling feet. Turn the leveling foot to the left to raise that side

of the product, or turn it to the right to lower that side of the product.

NOTE: Both leveling feet should be snug against the floor, and the rollers should not touch the floor. This keeps the

refrigerator from rolling forward when opening the doors.

Open both doors again and check that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by

turning the leveling feet to the left. It may take several more turns, and you should turn both leveling feet the same

amount.

5. Use a bubble level to check the leveling of the refrigerator.

NOTE: Whenever you need to move the refrigerator, turn the leveling feet to the right until they are no longer touching the ground. This will allow the refrigerator to roll more easily.

2. Open the freezer door. On the refrigerator door, place the handle on the shoulder screws with the setscrews facing the

freezer.

A. Shoulder screws

B. Setscrews inside the handle

3. Firmly push the handle toward the door until the handle base is flush against the door.

4. While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

Door Alignment

A refrigerator that is not level from side-to-side may appear to have doors that are not properly aligned. If the doors appear this

way, use the instructions in the previous section to check the leveling.

The doors are designed to be slightly different heights when the refrigerator is empty, in order to account for the weight of food

that will be placed on the doors. If the doors are still not aligned after checking the leveling and loading the refrigerator with food, follow the steps below to adjust the door alignment.

1. If necessary, open both doors to 90° and remove the base grille. See Graphic 1.

2. Locate the alignment screw on the bottom hinge of the refrigerator door. See Graphic 9.

3. Use a5Ae"open-ended or adjustable wrench to turn the screw. To raise the refrigerator door, turn the screw to the right. To lower the door, turn the screw to the left.

4. Check that the doors are even at the top. If necessary, continue to turn the alignment screw until the doors are aligned.

5. Open both doors to 90°. Replace the base grille. See

Graphic 1.

Handle nstaHation and Remova

PARTS INCLUDED: Door handles (2), 1/8"hex key, spare setscrew(s)

To Install the Handles:

NOTE: The handle mounting setscrews are preinstalled in the handle.

1. Remove the handles, which are packed inside the refrigerator. NOTE: To avoid scratching the finish, place the handles on a

towel or other soft surface.

Using a clockwise motion, tighten the setscrew until it begins to contact the shoulder screw.

Repeat steps 4 and 5 to begin fastening the lower setscrew.

Once both setscrews have been partially tightened as outlined in the previous steps, fully tighten both the upper and lower

setscrews. IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed without this extra tightening.

Open the refrigerator door and close the freezer door. Repeat steps 2 through 7 to install the other handle onto the freezer

door with the setscrews facing the refrigerator.

Save the hex key and all instructions.

Remove the Handles:

While holding the handle, insert the short end of the hex key into the lower setscrew hole and slightly rotate the hex key

until it is engaged in the setscrew.

Using a counterclockwise motion, loosen the setscrew a quarter-turn at a time.

Repeat steps 1 and 2 for the upper setscrew. Gently pull the handle away from the door.

If necessary, use a Phillips screwdriver to remove the shoulder screws from the door.

Location Requirements

E)ectrica) Requirements

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor household

use only. To ensure proper ventilation for your refrigerator, allow for 1/2"

(1.27 cm) of space on each side and at the top. Allow for 1" (2.54 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space on each side (depending on your model) to allow the doors to swing open.

r..1 r-

V2" (1.27

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF, and then disconnect the refrigerator from the

electrical source. When you are finished, reconnect the refrigerator to the electrical source and turn cooling on or reset the control (Thermostat, Refrigerator or Freezer Control depending on

the model) to the desired setting. See "Using the Controls" in the User Instructions, User Guide, or Use & Care Guide.

2" (5.08 cm)!

NOTES:

This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

Normal minimum cabinet cut-out width required for product installation is 36" (91.44 cm). However, if the product is placed

against an extended wall and the ability to remove the crisper pans is desired, an additional 18" (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54" (137.16 cm)is recommended.

Water Supp)y Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1/4"nut driver

• 7/le" and 1/2"open-end or • 1/4"drill bit two adjustable wrenches • Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/le" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain

above freezing.

Water Pressure Connect to Water Line

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

• If your refrigerator has a water dispenser: After installation is complete, use the water dispenser to check the water

pressure.

With the water filter removed, dispense 1 cup (237 mL) of water. If 1 cup of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

• If it takes longer than 8 seconds to dispense 1 cup of

water, the water pressure to the refrigerator is lower than recommended. See "Problem Solver" for suggestions.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and

827 kPa). If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration System" in the User Instructions, User Guide, or Use & Care

Guide.

If you have questions about your water pressure, call a licensed, qualified plumber.

Oonnect Water Supply

Read all directions before you begin.

IM PORTANI"."

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and

ordinances. The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator are acceptable, and will help avoid oft-taste or odor in your ice

or water. Check for leaks. If PEX tubing is used instead of copper, we recommend the

following Whirlpool Part Numbers: W10505928RP (7 ft [2.14 m] jacketed PEX), 8212547RP (5 ft [1.52 m] PEX), or

W10267701RP (25 ft [7.62 m] PEX).

• Install tubing only in areas where temperatures will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/le" and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFE

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a 1/2"copper household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a minimum 1/2"size copper household supply line is

recommended.

I/ II

A B

A. Bulb B. Nut

Now you are ready to connect the copper tubing to the shutoff

C. Copper tubing (to refrigerator) D. Household supply fine (Y2"minimum)

valve. Use 1/4"(6.35 mm) OD soft copper tubing to connect the shutoff valve and the refrigerator.

• Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

Slip compression sleeve and compression nut onto copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A. Compression sleeve

B. Compression nut

Place the free end of the tubing into a container or sink, and

C. Copper tubing

turn on main water supply to flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve, to avoid possible

water valve malfunction.

Bend the copper tubing to meet the water line inlet, which is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"(1.27 cm) to 11/4"(3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.

Install the water supply tube clamp around the water supply line to reduce strain on the coupling.

Turn shutoff valve ON.

Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the inlet of the water valve.

Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not

overtighten.

Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back

against the wall.

Turn shutoff valve ON.

Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

_.....................B

A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut

E. Compression sleeve E Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight

seal. Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the end of the water line inlet.

Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not

overtighten. NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the cabinet.

A B C

A. Household water line

B. Nut (purchased)

C. Ferrule (purchased) D. Refrigerator water tubing

__ A

.........................D

..... E

A. Tubeclamp D. Compression nut B. Tubeclamp screw E.Valveinlet

C.Copper tubing

On some models, the ice maker is equipped with a built-in water strainer. If your water conditions require a second water

strainer, install it in the 1/4"(6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long enough, a V4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed in

order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A B C

A. Refrigerator water tubing

B. Nut (provided) C. Bulb

D. Coupling (purchased)

D E F G

E. Ferrule (purchased)

E Nut (purchased)

G. Household water line

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Complete the Installation

1. Remove the air filter from its packaging.

2. Lift open the vented door.

3. Snap the filter into place.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water and Ice Dispensers" in the User Instructions or User Guide.

NOTE: Allow 24 hours to produce the first batch of ice. Allow 72 hours to completely fill ice container.

nstaH F[ te

(otn some mode_s}

On some models, your refrigerator's accessory packet includes an air filter, which must be installed prior to use. On some models,

the air filter is already installed at the factory.

4. Close the vented door.

Installing the Filter Status Indicator (on some models)

The filter comes with a status indicator, which should be activated and installed at the same time the air filter is installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until the bubble pops to activate the indicator.

3. Lift open the vented air filter door. On some models, there are notches behind the door.

4. On models with notches:

• Slide the indicator down into the notches, facing outward.

NOTE: The indicator will not easily slide into the notches if the rear bubble has not been popped.

Close the air filter door, and check that the indicator is visible through the rectangular hole in the door.

On models without notches:

• Store the indicator in a visible place you will easily

remember - either inside the refrigerator, or elsewhere in your kitchen or home.

The air filter reduces the buildup of odors. This helps to maintain a cleaner environment inside the refrigerator.

Installing the Air Filter (on some models)

The filter should be installed behind the vented door, which is located (depending on your model) along either the rear or left

interior wall near the top of the refrigerator compartment.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, when the status indicator has completely changed from white to red.

To order a replacement air filter, see "Accessories" in the User Instructions or User Guide.

1. Remove the old air filter by squeezing in on the side tabs.

2. Remove the old status indicator.

3. Install the new air filter and status indicator using the instructions in the previous sections.

nstaH P oduce P ese ve

(on some mode_s}

On some models, your refrigerator's accessory packet includes a Produce Preserver, which should be installed prior to use. On some models, the Produce Preserver is already installed at the

factory. The Produce Preserver absorbs ethylene, allowing the ripening

process of many produce items to slow down. As a result, certain produce items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type of fruit or vegetable. To preserve freshness, it is best to separate produce with sensitivity to ethylene from fruits that produce moderate to high amounts of ethylene.

The Produce Preserver pouches should be installed in their housing, which is located along an interior side wall of the crisper or convertible drawer.

Sensitivity to

Ethylene

Apples

Asparagus

Berries

Broccoli

Cantaloupe

Carrots Low Very Low

Citrus Fruit Med. Very Low

Grapes Low Very Low

Lettuce High Very Low

Pears High Very High

Spinach High Very Low

Installing the Produce Preserver (on some models)

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia, bleach or acids. Do not get in eyes, on skin or clothing. Do not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium permanganate. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

High

Med.

Low

High

Med.

Ethylene

Production

Very High

Very Low

Low

Very Low

High

NOTE: For best performance, always use two pouches.

1. Remove the Produce Preserver pouches from their packaging.

FreshFlow TM

produce preserver

CAUTION ATTENTION

IRRITANT IRRITANT

Read cautions on back. Life les mises en garde au dos,

2. Lift up on the housing in order to remove it from its mounting tab along the wall.

3. Open the housing by pulling up and out on the back of the top of the housing.

4. Place both pouches inside the housing, then snap the housing back together.

5. Place the housing back on the mounting tab along the wall.

Installing the Status Indicator (onsome models)

The Produce Preserver comes with a status indicator, which should be activated and installed at the same time the pouch is

installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until the bubble pops to activate the indicator.

3. Slide open the cap on the Produce Preserver housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's rear bubble has not been popped.

Replacing the Produce Preserver (on some models)

The disposable pouches should be replaced every 6 months, when the status indicator has completely changed from white to

red. To order replacements, see "Accessories" in the User Instructions

or User Guide.

1. Remove the old pouches from the Produce Preserver housing.

2. Remove the old status indicator.

3. Install the new pouches and status indicator using the instructions in the previous sections.

REFRIGERATOR USE

Using the Controls

The refrigerator and freezer controls are located on the dispenser panel.

IMPORTANT: The display screen on the dispenser control panel will turn off automatically and enter "sleep" mode when the

control buttons and dispenser pads have not been used for 2 minutes or more. While in "sleep" mode, the first press of a control button will only reactivate the display screen, without

changing any settings.

• Touch any control button on the dispenser panel to activate the display screen. The home screen will appear as shown.

8 as

Toview and adjust the set points, press and hold the TEMP button for 3 seconds. When adjust mode is activated, adjusting

information will appear on the display screen.

RECOMMENDED

FR,OGE --I --I °F

-I I

BACK UNITS SELECT ZONE _" A OU PM

NOTE: To view Celsius temperatures, press the LIGHT button

when adjust mode is activated. To return the display setting to Fahrenheit, press LIGHT again.

• When adjust mode is activated, the display screen shows the refrigerator set point and "FRIDGE" appears.

Press LOCK to raise the set point, or press FAST ICE to lower the set point.

When you have finished viewing (and adjusting if desired) the refrigerator set point, press TEMP to change the display to

show the freezer set point. When the zone has been changed, "FREEZER" appears on the display screen.

Press LOCK to raise the set point, or press FAST ICE to lower the set point.

When you have finished viewing (and adjusting if desired) both the refrigerator and freezer set points, press FILTER to save the settings.

NOTE: To exit without saving changes, press ICE TYPE at any time while in adjust mode, or allow about 60 seconds of

inactivity and adjust mode will turn off automatically.

When adjusting temperature set points, use the following chart as a guide.

CONDITION: TEMPERATURE

ADJUSTMENT:

Adjusting the Controls

For your convenience, your refrigerator and freezer controls are preset at the factory. When you first install your refrigerator, make sure that the controls are still set to the "mid-settings." The factory

recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer.

IM PORTANI"."

• Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your

food may spoil. NOTE: Adjusting the set points to a colder than

recommended setting will not cool the compartments any faster.

If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made.

REFRIGERATOR too cold REFRIGERATOR Setting

1° higher

REFRIGERATOR too warm REFRIGERATOR Setting

1° lower

FREEZER too cold FREEZER Setting

1° higher

FREEZER too warm / FREEZER Setting Too little ice 1° lower

The set point range for the refrigerator is 33°F to 45°F (0°C to 7°C). The set point range for the freezer is -5°F to 5°F (-21 °C to

-15°C).

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is turned off.

• To turn cooling off, press and hold the LOCK and FILTER buttons at the same time for 3 seconds.

IMPORTANT: To avoid unintentionally locking the dispenser or changing other settings, be sure to press both buttons at exactly the same time.

When cooling is off, "COOLING OFF" will appear on the display screen.

Press and hold LOCK and FILTER for 3 seconds again to turn cooling back on.

Additional Features

Fast Ice

The Fast Ice feature assists with temporary periods of heavy ice use by increasing ice production over a 24-hour period.

IMPORTANT: This feature only works if the ice maker is turned on. See "Ice Maker and Storage Bin."

• Press FAST ICE to turn on the Fast Ice feature. When the feature is on, the Fast Ice icon will appear on the dispenser

display screen. The Fast Ice setting will remain on for 24 hours unless manually turned off.

• To manually turn off the Fast Ice feature, press FAST ICE again or adjust the freezer temperature set point. The Fast Ice icon will disappear when the feature is off.

NOTE: If increased ice production is desired at all times, change the freezer set point to a lower setting. Setting the freezer to a

colder temperature may make some foods, such as ice cream, harder.

6th Sense _ Temperature Management (on some models) The 6th Sense _feature assists with regulating the temperature

inside the refrigerator. If a large quantity of warm food is placed in the refrigerator or warm air enters the refrigerator while the door is held open, the 6th Sense®system activates to quickly restore the

temperature to the set point.

sense

NOTE: The 6th Sense®system is always on when your refrigerator

is operating. You do not need to press any buttons to activate it. The 6th Sense ®icon on the dispenser display screen indicates

that the feature is functioning properly.

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the refrigerator or freezer door is open for 5 minutes and the product cooling is

turned on. The alarm will repeat every 2 minutes. Close both doors to turn it off. The feature then resets and will reactivate

when either door is left open again for 5 minutes. NOTE: To mute the audible alarm while keeping the doors open,

such as while cleaning the inside of the refrigerator, press any button on the control panel. The alarm sound will be temporarily turned off, but the Door Ajar icon will still be displayed on the

dispenser control panel.

Oonve£ib e © awe

.... %mperatu e Oontro

(on some mode_s}

The control can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to avoid "spot" freezing and can be set to keep meats at the National Livestock and Meat Board

recommended storage temperatures of 28° to 32°F (-2° to O°C). To store meat:

Set the control to one of the three MEAT settings to store meat at its optimal storage temperature.

To store vegetables:

Set the control to VEG to store vegetables at their optimal storage temperatures.

NOTE: If food starts to freeze, move the control to the right (less cold), toward the VEG setting. Remember to wait 24 hours

between adjustments.

O isper Humic/ity Oont ol

{on some models}

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins. HIGH (closed) for best storage of fresh, leafy vegetables.

Water and ©ispense s

NOTES:

• The dispensing system will not operate when either door (refrigerator or freezer) is open.

• Allow 24 hours for the refrigerator to cool down and chill water.

Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Wait 72 hours for full ice production.

The display screen on the dispenser control panel will turn off automatically and enter "sleep" mode when the control buttons and dispenser pads have not been used for 2 minutes or more. While in "sleep" mode, the first press of a control

button will only reactivate the display screen, without changing any settings.

Flush the Water System

Dual Evaporator (on some models)

Some models come equipped with a dual sequential evaporation system, which includes two separate evaporators for the

refrigerator and freezer compartments. Dual evaporation results in higher humidity, which helps keep

foods in the refrigerator from spoiling as quickly and improves food quality and freshness in the freezer due to decreased freezer

burn. In addition, the dual evaporation system helps keep food smells in the refrigerator from transferring to ice in the freezer.

NOTE: The dual evaporation system is always activated when your refrigerator is operating. You do not need to press any

buttons to turn it on.

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or

replacing the water filter, flush the water system. Flushing the water dispensing system forces air from the water line and filter, and prepares the water filter for use.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1. Using a sturdy container, depress and hold the water dispenser pad for 5 seconds, then release it for 5 seconds.

2. Repeat Step 1 until water begins to flow.

3. Once water begins to flow, continue depressing and releasing the dispenser pad (5 seconds on, 5 seconds off) until atotal of 3 gal. (12 L) has been dispensed.

Additional flushing may be required in some households.

The Water Dispenser

IM PORTANT:

• Dispense at least 1 qt (1 L) of water every week to maintain a fresh supply.

• If the flow of water from the dispenser decreases, it could be caused by low water pressure.

With the water filter removed, dispense 1 cup (237 mL) of water. If 1 cup of water is dispensed in 8 seconds or less,

the water pressure to the refrigerator meets the minimum requirement.

If it takes longer than 8 seconds to dispense 1 cup of water, the water pressure to the refrigerator is lower than recommended. See "Water Supply Requirements" or "Troubleshooting" or "Problem Solver" for suggestions.

To Dispense Water:

1. Press a sturdy glass against the water dispenser pad. Hold the glass close to the water dispenser spout to ensure that the water dispenses into the glass.

To Dispense Ice:

1. Make sure the desired type of ice is selected. To switch between cubed and crushed, press ICE TYPE.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

2. Press a sturdy glass against the ice dispenser pad. Hold the glass close to the ice guide to ensure that the ice dispenses into the glass.

A. Water dispenser spout

2. Remove the glass to stop dispensing.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer when the dispenser pad is pressed. To turn off the ice maker, see "Ice Maker and Storage Bin."

Your ice maker can produce both crushed and cubed ice. Before dispensing ice, select which type of ice you prefer by pressing the

ICE TYPE button. The display screen indicates which type of ice is selected.

CRUSHED CUBED

For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed

ice will be dispensed along with the first cubes.

A. Ice guide

IMPORTANT: You do not need to apply a lot of pressure to the pad in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

Remove the glass to stop dispensing. NOTE: Ice may continue to dispense for several seconds after

removing the glass from the pad. The dispenser may continue to make noise for a few seconds after dispensing.

The Dispenser Light

When you use the dispenser, the light will automatically turn on. If you want the light to be on continuously, you may choose either ON or DIM. The display screen indicates which mode is selected.

ON DIM

ON: Press LIGHT to turn the dispenser light on. DIM: Press LIGHT a second time to select DIM mode. The dispenser light will remain on, but at a lower intensity.

OFF: Press LIGHT a third time to turn the dispenser light off. The dispenser lights are LEDs that cannot be changed. If it

appears that your dispenser lights are not working, see "Troubleshooting" or "Problem Solver" for more information.

The DispenserLock

The dispenser can be turned off for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the controls and dispenser pads. To turn off the ice maker, see "Ice

Maker and Storage Bin."

• Press and hold LOCK for 3 seconds to lock the dispenser.

• Press and hold LOCK a second time to unlock the dispenser. The display screen indicates when the dispenser is locked.

LOCKED UNLOCKED

Maker and Storage Bin

Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well

maintained. Do not use anything sharp to break up the ice in the storage

bin. This can cause damage to the ice container and the dispenser mechanism.

Do not store anything on top of or in the ice maker or storage bin.

Removing and Replacing the Ice Storage Bin:

1. Press down the release lever and tilt the bucket outward. Use both hands to hold the base of the storage bin, then lift it up

and out.

A. Release lever

NOTE: It is not necessary to turn the ice maker control to the OFF (right) position when removing the storage bin. The sensor cover ("flipper door"), located on the right wall of the freezer door, stops the ice maker from producing ice if the

door is open or the storage bin is removed.

Style I

Turning the Ice Maker On/Off:

The On/Off switch can only be accessed when the ice storage bin has been removed. The switch is located on the freezer door, on

the left side of the wall that surrounds the ice storage bin. See the following section for bin removal instructions.

Ice Maker Control

• To turn on the ice maker, slide the control to the ON (left) position.

• To manually turn off the ice maker, slide the control to the OFF (right) position.

NOTE: The ice maker has an automatic shutoff to keep the storage bin from overfilling during normal operation. The ice

maker sensors will automatically stop ice production, but the control will remain in the ON (left) position.

A. On/Off switch B. Sensorcover

2. Replace the bin by sliding it onto the door, then tilting it back into an upright position. The release lever will click when the

bin is securely in place.

Style 2

Turning the Ice Maker On/Off:

• Toturn ON the ice maker,simply lower thewire shutoff arm.

• To manually turn off the ice maker, lift the wire shutoff arm to the OFF (arm up) position and listen for the click. Ice can still be dispensed, but no more can be made.

NOTE: The ice maker has an automatic shutoff to keep the storage bin from overfilling during normal operation. As ice is

made, the ice cubes will fill the ice storage bin, and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position. Do not force the wire shutoff arm up or down.

Removing and Replacing the Ice Storage Bin:

1. Pull the covering panel up from the bottom.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

3. Lift up the front of the storage bin and pull it out.

Replace the bin by pushing it in all the way or the dispenser will not work.

To restart ice production, lower the wire shutoff arm into the ON (down) position. Make sure the door is closed tightly.

Water Filtration System

When the door is completely open, pull the filter straight out. NOTE: There may be some water inthe filter. Some spilling

may occur. Use a towel to wipe up any spills.

Take the new filter out of its packaging and remove the cap. Be sure the O-rings are still in place after the cap is removed.

A B

A. Cap B. O-nngs

5. With the arrow pointing up, align the new filter with the filter housing and slide it into place. The filter cover door will automatically begin to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap the filter into place. You may need to press hard.

7. Flush the water system. See "Water and Ice Dispensers."

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Water Filter Status Light

The water filter status light will help you know when to change your water filter.

• When the dispenser control panel's water filter status display changes to "ORDER," this tells you that it is almost time to

change the water filter cartridge.

• Replace the water filter cartridge when the water filter status display changes to "REPLACE."

NOTE: If water flow to your water dispenser or ice maker decreases noticeably, change the filter sooner. The filter should be replaced at least every 6 months, depending on your water quality and usage.

Resetting the Filter Status

• After changing the water filter, reset the status light by pressing and holding the FILTER button for 3 seconds.

When the system is reset, the "ORDER" and "REPLACE" icons will disappear from the display screen.

Changing the Water Filter

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.

1. Locate the water filter inthe top-right corner of the refrigerator compartment.

2. Lift open the filter cover door. The filter will be released and then be ejected as the door is opened.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

Remove the base grille. See the "Door Removal" instructions, either in the User Instructions or the

Installation Instructions and Owner's Manual, or in the separate instruction sheet provided with your refrigerator.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

IMPORTANT: The light bulbs in both the refrigerator and freezer compartments of your new refrigerator may use LED technology. If the lights do not illuminate when the refrigerator and/or freezer door is opened, call for assistance or service. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.

Light Styles: The dispenser lights are mini LEDs that cannot be changed. The interior lights vary by model.

• Some models have mini LEDs that cannot be changed.

• Some models have full-size LED bulbs that can be

changed. To order replacement LED bulbs, call 1-800-253-1301 (U.S.A.) or 1-800-807-6777 (Canada).

To Change a Light Bulb:

1. Unplug refrigerator or disconnect power.

2. Remove the light shield, as explained in the following sections.

NOTE: To clean the light shield, wash it with warm water and liquid detergent. Before reinstalling, thoroughly rinse and dry

the shield.

3. Replace the burned-out light bulb, as explained in the following sections.

4. Reinstall the light shield, as explained in the following sections.

5. Plug in refrigerator or reconnect power.

Refrigerator Compartment - Upper Lights

Light Shield Removal:

• Slide the light shield toward the rear of the refrigerator and remove it from the light housing.

Replacement Bulb:

• If the burned-out light is afull-size LED bulb, replace it with Whirlpool part number W10574850A (a 2.0 watt LED bulb).

• If the burned-out light is an incandescent bulb, replace it with an incandescent appliance bulb of the same size, shape and

wattage (40-watt maximum).

Light Shield Reinstallation:

• Align the light shield in the grooves at the bottom edge of the light housing, then slide it forward until it snaps into place.

Whirlpool

Part Number

W10574850A

(2.0 watts)

Whirlpool

Part Number

W10565137A

(3.6 watts)

NOTE: Some LED replacement bulbs are not recommended for wet/damp environments. The

refrigerator and freezer compartments are considered to be wet/damp environments. If using a brand of LED bulb

other than the recommended Whirlpool LED bulb, read and follow all instructions on the replacement bulb's

packaging before installing it. Some models have incandescent 40-watt bulbs that can be changed.

NOTE: Not all replacement bulbs will fit your refrigerator. Do not use an incandescent bulb in excess of 40 watts.

Refrigerator Compartment - Lower Lights

Light Shield Removal:

• Slide the light shield to the right to remove the left end from the wall slots, then pull the right end out of its wall slots.

Replacement Bulb:

• If the burned-out light is afull-size LED bulb, replace it with Whirlpool part number W10565137A (a 3.6 watt LED bulb).

• If the burned-out light is an incandescent bulb, replace it with an incandescent appliance bulb of the same size, shape and wattage (40-watt maximum).

Light Shield Reinstallation:

• Place the right end of the light shield into the wall slots, then snap the left end into its wall slots.

Freezer Compartment - Upper Light

Light Shield Removal:

• Gently squeeze the front and the bottom-rear edge of the light shield to release the tabs from the wall slots, then pull the light

shield forward.

Freezer Compartment - Lower Light

Light Shield Removal:

• Slide the light shield to the left to remove the right end from the wall slots, then pull the left end out of its wall slots.

Replacement Bulb:

• If the burned-out light is afull-size LED bulb, replace it with Whirlpool part number W10565137A (a 3.6 watt LED bulb).

• If the burned-out light is an incandescent bulb, replace it with an incandescent appliance bulb of the same size, shape and wattage (40-watt maximum).

Light Shield Reinstallation:

• Place the left end of the light shield into the wall slots, then snap the right end into its wall slots.

Replacement Bulb:

• If the burned-out light is afull-size LED bulb, replace it with Whirlpool part number W10565137A (a 3.6 watt LED bulb).

• If the burned-out light is an incandescent bulb, replace it with an incandescent appliance bulb of the same size, shape and wattage (40-watt maximum).

Light Shield Reinstallation:

• Align the light shield in its proper position, and snap the tabs into the wall slots.

Vacation and Movin 9 Care

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is connected to the household water supply, turn off the water supply to the refrigerator. Property damage can occur if the water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker. NOTE: Depending on your model, raise the wire shutoff arm to

OFF (up) position or press the switch to OFF (right).

4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF (right) setting.

3. Depending on the model, turn the Refrigerator Control to OFF or turn cooling off. See "Using the Controls" in the User Instructions, User Guide, or Use & Care Guide.

4. Clean, wipe, and dry thoroughly.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• Disconnect the water line from the back of the refrigerator.

• When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Refrigerator Control to OFF or turn cooling off. See "Using the Controls" in the User Instructions, User Guide, or Use & Care Guide.

PROBLEM SOLVER

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.whirlpool.com In Canada, www.whirlpool.ca

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See "Adjust the Doors" or "Door Removal, Leveling and Alignment."

9. Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to the Installation Instructions for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Refrigerator • Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet. will not operate Do not use an extension cord.

• No power to the electrical outlet - Plug in a lamp to see if the outlet is working.

• Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the circuit breaker. If the problem continues, contact a licensed electrician.

• Control or cooling is not turned on - Turn on the refrigerator control, or turn cooling on. See "Using the Controls."

• New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either compartment (refrigerator or freezer) more quickly.

Motor seems to run too much

Your new refrigerator has an energy-efficient motor - The refrigerator may run longer than

you're used to, because the compressor and fans operate at lower speeds that are more

energy-efficient. This is normal. NOTE: Your refrigerator may run even longer if the room is warm, a large load of food is added,

the doors are opened often, or if a door has been left open.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Refrigerator seems noisy The compressor inyour new refrigerator regulates temperature more efficiently and uses less energy

Temperature is too warm New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

than older models. During various stages of operation, you may hear normal operating sounds that

are unfamiliar.

The following noises are normal:

• Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or fill the ice maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator is not connected to a water line, turn off the ice maker.

• Cracking/Crashing - Heard when ice is ejected from the ice maker mold.

• Popping - Heard when the inside walls contract/expand, especially during initial cooldown.

• Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during normal operation.

• Rattling - Heard when water passes through the water line, or due to the flow of refrigerant. Rattling may also come from items placed on top of the refrigerator.

• Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into

the drain pan.

• Sizzling - Heard when water drips onto the heater during the defrost cycle.

completely. NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly. Doors are opened often or not closed completely - This allows warm air to enter the

refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are properly sealed.

Air vents are blocked - Remove items that are immediately in front of the vents.

Large amount of warm food recently added - Allow several hours for the refrigerator to return

to its normal temperature. Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder

setting. Check the temperature again in 24 hours.

Temperature is too cold Controls are not set correctly for the surrounding conditions - Adjust the controls to a

Interior moisture buildup NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.

Interior lights do not work • Doors have been open for an extended period of time - Close the doors to reset the lights.

Dispenser lights do not work

(on some models)

warmer setting. Check the temperature again in 24 hours. Top refrigerator shelf is colder than lower shelves - On some models, air from the freezer

enters the refrigerator compartment through vents near the top refrigerator shelf. As a result, the

top shelf can be slightly colder than lower shelves.

• Air vents are blocked - Remove items that are immediately in front of the vents.

• Room is humid - A humid environment contributes to moisture buildup. Use the refrigerator only in an indoor location, with as little humidity as possible.

• Doors are opened often or not closed completely - This allows humid air to enter the refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are properly sealed.

• Light bulb is loose in the socket or has burned out - On models with incandescent or full-size LED interior light bulbs, tighten or replace the bulb. See "Lights."

NOTE: On models with mini LED lights, call for assistance or service if the interior lights do not illuminate when either door is opened. See either the front cover or the Warranty for contact

information.

• Dispenser light is turned off - On some models, if the dispenser light is set to OFF, the light will

turn on only when a dispenser pad/lever is pressed. If you want the dispenser light to stay on

continuously, select a different setting. See "Water and Ice Dispensers."

• Dispenser light is set to AUTO or NIGHT LIGHT - On some models, if the dispenser light is set

to AUTO or NIGHT LIGHT, make sure the dispenser light sensor is not blocked. See "Water and

Ice Dispensers."

NOTE: On models with mini LED lights, call for assistance or service if the dispenser lights do not operate correctly. See either the front cover or the Warranty for contact information.

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions

Doors are difficult to open • Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and warm

Doors will not • Door is blocked open - Move food packages away from the door. Make sure all bins and

close completely shelves are in their correct positions. Make sure all packaging materials have been removed.

Doors appear to be uneven • Doors need to be aligned, or refrigerator needs to be leveled - See the leveling and door

Refrigerator rocks and is not stable

ICE AND WATER Possible Causes and/or Recommended Solutions

water. Rinse and dry with a soft cloth.

alignment instructions.

• Refrigerator is not level - To stabilize the refrigerator, remove the base grille and lower the leveling feet until they touch the floor. See the leveling and door alignment instructions.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

Ice maker is not • producing ice,

not producing enough ice,

or producing small/hollow ice

Refrigerator is not connected to a water supply, or the water supply shutoff valve is not fully turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is fully open.

Kink in the water source line - A kink in the water line can reduce water flow, resulting in decreased ice production, small ice cubes, and/or hollow or irregularly-shaped ice. Straighten the water line.

Ice maker is not turned on - Turn on the ice maker. See "Ice Maker and Storage Bin." New installation - After connecting the refrigerator to a water source, flush the water system.

(See "Water and Ice Dispensers.") Wait 24 hours for ice production to begin. Wait 72 hours for full ice production. Discard the first three batches of ice produced.

Large amount of ice was recently removed - Allow sufficient time for the ice maker to produce more ice.

• Ice is jammed in the ice maker ejector arm - Remove ice from the ejector arm using a plastic utensil.

• Inadequate water pressure - Verify that the household has adequate water pressure. See "Water Supply Requirements."

• Water filter is installed incorrectly - Make sure the filter is properly installed. See "Water Filtration System."

• A reverse osmosis water filtration system is connected to your cold water supply - This can decrease water pressure. See "Water Supply Requirements."

NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice dispenser • will not operate

properly •

Ice or water has an off-taste, odor,

or gray color

Doors not closed completely - Make sure both doors are firmly closed. (On some modems,only the

freezer door must be closed in order to operate the dispenser.) New installation - After connecting the refrigerator to a water source, flush the water system.

(See "Water and Ice Dispensers.") Wait 24 hours for ice production to begin. Wait 72 hours for full ice production. Discard the first three batches of ice produced.

Ice maker is not turned on, or ice bin is not installed correctly - Turn on the ice maker and make sure the ice storage bin is firmly in position. See "Ice Maker and Storage Bin."

Ice is clogged or frozen together in the ice storage bin, or ice is blocking the ice delivery chute - Remove or separate the clogged ice, using a plastic utensil if necessary. Clean the ice delivery chute and the bottom of the ice storage bin using a warm damp cloth, then dry both thoroughly. To avoid

clogging and to maintain afresh supply of ice, empty the storage bin and clean both the storage bin and the delivery chute every 2 weeks.

Wrong ice has been added to the storage bin - Use only ice cubes produced by the current ice maker.

Dispenser is locked - Unlock the dispenser. See "Water and Ice Dispensers." Ice dispenser jams while dispensing crushed ice - For models with the ice storage bin on the door,

temporarily switch from crushed ice to cubed ice to clear the jam. Dispenser pad/lever has been pressed too long - Ice will automatically stop dispensing. Wait a few

minutes for the dispenser to reset, then resume dispensing. Take large amounts of ice directly from the ice bin, not through the dispenser.

Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home

affects the flow from the dispenser. See "Water Supply Requirements."

Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See "Water

Filtration System."

New plumbing connections - New plumbing connections can result in off-flavored or discolored ice or water. This problem should go away over time.

Ice has been stored too long - Discard the ice and wash the ice bin. Allow 24 hours for the ice maker to produce new ice.

Odor has transferred from food - Use airtight moisture-proof packaging to store food. Use of non-recommended water supply line - Odors and tastes can transfer from certain materials

used in non-recommended water supply lines. Use only a recommended water supply line. See "Water Supply Requirements."

There are minerals (such as sulfur) in the water - A water filter may need to be installed in order to

remove the minerals.

Water filter was recently installed or replaced - Gray or dark discoloration in ice or water indicates

that the water filtration system needs additional flushing. See "Water and Ice Dispensers."

Water dispenser will not operate

properly

• Doors not closed completely - Make sure both doors are firmly closed. (On some models, only the freezer door must be closed in order to operate the dispenser.)

• Refrigerator is not connected to a water supply, or the water supply shutoff valve is not turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is fully open.

• Kink in the water source line - A kink in the water line can reduce water flow to the dispenser. Straighten the water line.

• Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home affects the flow from the dispenser. See "Water Supply Requirements."

• New installation - After connecting the refrigerator to a water source, flush the water system. See "Water and Ice Dispensers."

• Dispenser is mocked - Unlock the dispenser. See "Water and Ice Dispensers."

• Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See "Water Filtration System."

• A reverse osmosis water filtration system is connected to your cold water supply - This can decrease water pressure. See "Water Supply Requirements."

NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.

ICE AND WATER Possible Causes and/or Recommended Solutions

Water is leaking or dripping from the

dispenser

NOTE: After dispensing, a few additional drops of water are normal.

• Glass was not held under the dispenser long enough - Hold the glass under the dispenser for 2 to 3 seconds after releasing the dispenser pad/lever.

• New installation, or water filter was recently installed or replaced - Air inthe water lines causes the water dispenser to drip. Flush the water system to remove the air inthe water lines. See "Water and Ice

Dispensers."

• Residual ice in the dispenser chute is melting - Make sure the ice chute is free of ice shavings or pieces.

Water is leaking • Water line connections are not fully tightened - Make sure all connections are firmly tightened. See from the back of the "Connect Water Supply." refrigerator

Water from the dispenser is

not cool enough (on some models)

NOTE: Water from the dispenser is chilled to 50°F (10°C).

• New installation - Allow 24 hours after installation for the water supply to cool completely.

• Recently dispensed a large amount of water - Allow 24 hours for the new water supply to cool completely.

• Water has not been recently dispensed - The first glass of water may not be cool. Discard the first glass of water dispensed.

• Refrigerator is not connected to a cold water pipe - Make sure the refrigerator is connected to a cold water pipe. See "Water Supply Requirements."

ACCESSORIES

The following accessories are available for your refrigerator. To order an accessory: Contact us and ask for the part number

listed, or contact your authorized dealer. In the U.S.A., call 1-800-442-9991 or visit www.whirlpool.com/

accessories. In Canada, call 1-800-807-6777 or visit www.whirlpool.ca.

affresh ®Stainless Steel Cleaner: Order Part #W10355016 In Canada, order Part #W10355016B

affresh ®Stainless Steel Wipes: Order Part #W10355049 In Canada, order Part #W10355049B

affresh ®Kitchen & Appliance Cleaner: Order Part #W10355010

In Canada, order Part #W10355010B Water Filter:

Order Part #W10295370A (P4RFWB) Air Filter:

Order Part #W10311524 Produce Preserver:

Order Part #W10346771

Cysts

Organic Contamiaant_

Atrazme

WATER FILTER

CERTIFICATIONS

State of Calitbrnia

Department of Public tleal_h

WaterTreatmentDevice

CertificateNumber

10-2030

Date Issued: February 26, 2010

Rated Service Capacity: 200 ga] ilated Service Flow: 05 gpm

Do not use where water is mierobiologically unsafe or with water of unknown _ualiiy, excepl that syslem_ ceifified fbr cyst reduction may be used on disinfected waters that may coniam fillerable cysts.

Conditions of Certification i

PERFORMANCE DATA SHEET

Water Filtration System

Model P5WB2L/P4RFWB Capacity 200 Gallons (757 Liters)

System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor, and Particulate

Class I*; and against NSF/ANSI Standard 53 for the reduction of Live Cysts, Asbestos, Lead, Lindane, Toxaphene, Atrazine, and 2,4 - D.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to

the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction Aesthetic Effects

Chlorine Taste/Odor Particulate Class I*

Contaminant

Reduction Live Cysts t

Asbestos

Lead: @ pH 6.5 Lead: @ pH 8.5

Lindane

Toxaphene Atrazine

2,4 - D

Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

NSF Reduction Requirements

50% reduction 85% reduction

NSF Reduction Requirements

99.95% 99%

0.010 mg/L

0.0002 mg/L

0.003 mg/L

0.07 mg/L

Average Influent

2.0 mg/L 7,300,000 #/mL

Average

Influent 160,000/L

87 MFL

0.160 mg/L

0.140 mg/L

0.0019 mg/L

0.014 mg/L

0.0094 mg/L

0.220 mg/L

Influent Challenge Concentration

2.0 mg/L _+10%

At least 10,000 particles/mL

Influent Challenge Concentration

50,000/L rain. 107to 108fibers/U _

0.15 mg/L _+10%

0.15 rag/L_+ 10%

0.002 mg/L _+10%

0.015 mg/L _+10%

0.009 rag/L_+ 10%

0.210 rag/L_+ 10%

Maximum Effluent

0.20 mg/L 75,000 #/mL**

Maximum Effluent

54/U

0.17 MFL

0.001 mg/L

0.005 mg/L

0.00002 mg/L

0.001 mg/L

0.0005 mg/L

0.028 mg/L

Minimum % Reduction

97 99

Minimum % Reduction

99.97 99

99.4

98.6

98.9 93

94.5

87.5

Average %

Reduction

97.2

99.4

Average %

Reduction

99.99 99

99.4

98.6 99 93

94.7

96.1

It is important that operational, maintenance, and filter • replacement requirements be carried out for the product to

perform as advertised. Property damage can occur if all • instructions are not followed.

Use replacement filter P4RFWB, part #W10295370A. 2013 suggested retail price of $39.99 U.S.A./S49.99 Canada. Prices are subject to change without notice.

Style 1- When the water filter status display changes from "GOOD" to "ORDER," order a new filter. When the filter

indicator reads "REPLACE," it is recommended that you replace the filter.

Style 2 - When the filter indicator changes from green to yellow, order a new filter. When the indicator changes from yellow to red, it is recommended that you replace the filter.

Style 3 - When the filter indicator reads 10%, order a new filter. When the indicator reads 0%, it is recommended that

you replace the filter. Style 4- Press FILTER to check the status of your water filter.

If the filter indicator light is yellow, order a new filter. If the filter indicator light is red, it is recommended that you replace the

filter. After changing the water filter, flush the water system. See

"Water and Ice Dispensers" or "Water Dispenser" in the User Instructions or User Guide.

These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary.

The product is for cold water use only. The water system must be installed in compliance with state

and local laws and regulations. Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Refer to the "Warranty" section (in the User Instructions or User Guide) for the Manufacturer's name, address and telephone number.

Refer to the "Warranty" section (in the User Instructions or User Guide) for the Manufacturer's limited warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well Water Pressure 30 - 120 psi (207 - 827 kPa) Water Temperature 33° - 100°F (0.6 ° - 37.8°C)

Service Flow Rate 0.5 gpm (1.9 Lpm) @60 psi

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

tBased on the use of Cryptosporidium parvum oocysts

ttFibers greater than 10 um in length

® NSF is a registered trademark of NSF International.

WHIRLPOOL CORPORATION MAJOR APPLIANCE

WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be provided by a Whirlpool designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Any food or medicine loss due to refrigerator or freezer product failures.

7. Pickup and delivery. This major appliance is intended to be repaired in your home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Whirlpool servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Whirlpool's published installation instructions.

11. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined.

12. Discoloration, rust, or oxidation of stainless steel surfaces.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies. 7/12 For additional product information, in the U.S.A., visit www.whirlpool.com.

In Canada, visit www.whirlpool.ca. If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may

contact Whirlpool at the number below.

Have your complete model number ready. You can find your model number and serial number on the label, located on the inside wall of the refrigerator compartment.

For assistance or service in the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. If you need further assistance, you can write to Whirlpool with any questions or concerns at the address below:

In the U.S.A.: In Canada:

Whirlpool Brand Home Appliances Customer eXperience Center

553 Benson Road Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence. Please keep all provided instructions and your model number information for future reference.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

Whirlpool Brand Home Appliances Customer eXperience Centre 200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

+ 58 hidden pages