Whirlpool WGTLV27HW0, WGTLV27HW1, WGT4027HW0, WETLV27HW1, WETLV27HW0 Owner’s Manual

WASHER/DRYER

USE AND CARE GUIDE

LAVEUSE/SÉCHEUSE

GUIDE D’UTILISATION

ET D’ENTRETIEN

Table of Contents

WASHER/DRYER SAFETY ...........................................2

WHAT’S NEW UNDER THE LID? .................................4

ACCESSORIES .............................................................. 5

USING LESS WATER AND ENERGY ...........................5

CHECK YOUR VENT SYSTEM

FOR GOOD AIRFLOW .................................................6

CONTROL PANEL AND FEATURES ............................7

WASHER CYCLE GUIDE ..............................................8

DRYER CYCLE GUIDE ...............................................10

USING YOUR WASHER ..............................................11

USING YOUR DRYER .................................................14

ADDITIONAL FEATURES ............................................15

WASHER/DRYER MAINTENANCE ............................16

TROUBLESHOOTING ................................................. 20

WARRANTY .................................................................26

ASSISTANCE OR SERVICE ........................ Back Cover

Table des matières

SÉCURITÉ DE LA LAVEUSE/SÉCHEUSE .................27

QUOI DE NEUF SOUS LE COUVERCLE? .................30

ACCESSOIRES ............................................................ 31

RÉDUCTION DE LA CONSOMMATION D’EAU

ET D’ÉNERGIE. ...........................................................31

VÉRIFICATION D’UNE CIRCULATION D’AIR ADÉQUATE POUR LE SYSTÈME

D’ÉVACUATION .......................................................... 32

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES ...........................................33

GUIDE DE PROGRAMMES DE LA LAVEUSE ...........35

GUIDE DE PROGRAMMES DE LA SÉCHEUSE ........ 37

UTILISATION DE LA LAVEUSE ..................................38

UTILISATION DE LA SÉCHEUSE ............................... 41

CARACTÉRISTIQUES SUPPLÉMENTAIRES.............43

ENTRETIEN DE LA LAVEUSE/SÉCHEUSE ...............44

DÉPANNAGE ............................................................... 48

GARANTIE ................................................................... 59

ASSISTANCE OU SERVICE ............ Couverture arrière

Designed to use only HE High Efﬁciency detergents. Conçue pour utiliser un détergent haute efﬁcacité seulement.

W11028710A

W11105978A-SP

WASHER/DRYER SAFETY

WARNING:

FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury, death, or property

damage.

–

Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.

–

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Clear the room, building, or area of all occupants.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

•

instructions. If you cannot reach your gas supplier, call the re department.

•

–

Installation and service must be performed by a qualied installer, service agency, or the gas supplier.

WHAT’S NEW UNDER THE LID?

Your new washer will operate differently than your past agitator-style washer.

Lid Lock

To allow for higher spin speeds, the lid will lock and the Lid Lock light will turn on. When this light is lit, the lid is locked and cannot be opened. When this light is blinking, the washer is paused. When this light is off, the lid can be opened. If you need to open the lid to add a garment after this point, the lid will remain unlocked during the entire agitation portion of the wash phase. The cycle will automatically pause when the lid is opened, and the cycle will resume once the lid is closed. The lid will lock before the spin phase begins. If you need to pause or stop after this point, you must press the START/PAUSE button and wait for the lid to unlock. The lid will only unlock after washer movement has stopped. Depending on when in the cycle you try to pause, it may take several seconds to several minutes for the lid to unlock. Press the START/ PAUSE button to resume the cycle.

Sensing

This washer will perform a series of spins to check for load balance. During this time, a series of clicks and a whirring noise signal that sensing technology is determining if there is an off-balance load.

Sounds

At different stages of the wash cycle, you may hear sounds and pauses that are different from those of your previous washer. For example, you may hear a clicking and hum at the beginning of the spin phase as the lid lock goes through a self-test. There will be different kinds of humming and whirring sounds as the agitator tests for load balance or moves the load. And sometimes, you may hear nothing at all as the washer determines the correct water level for your load or allows time for clothes to soak.

Choosing the Right Detergent

Use only High Efciency detergents. The package will be marked “HE” or “High Efciency.” Using non-HE detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component malfunction and, over time, buildup of mold or mildew. HE detergents should be low-sudsing and quick-dispersing to produce the right amount of suds for the best performance. They should hold soil in suspension so it is not redeposited onto clean clothes. Not all detergents labeled as High Efciency are identical in formulation and their ability to reduce suds. For example, natural, organic, or homemade HE detergents may generate a high level of suds. Always follow the detergent manufacturer’s instructions to determine the amount of detergent to use.

Use only High Efciency (HE) detergent.

Spray Rinse

Select cycles default to a spray rinse. During these cycles, you will hear water enter the washer as the tub spins, allowing the rinse water to penetrate clothes. Check the “Cycle Guide” for details.

IMPORTANT:

■ The lid must be closed before the washer basket lls with water and for the wash cycle to start. If the lid is open and lling stops,

close the lid and press the START/PAUSE button to complete the cycle.

■ Fabric Softener knob must be set to Yes when using fabric softener in the fabric softener dispenser. This ensures that fabric

softener is added at the correct time in the rinse phase and is evenly distributed.

ACCESSORIES

Enhance your new washer/dryer with the following genuine Whirlpool Accessories. For more information on options and ordering, call

1-800-901-2042 or visit us at: www.whirlpool.com/accessories. In Canada, call 1-800-807-6777 or visit us at www.whirlpoolparts.ca.

Washer Dryer

Fabric Softener Dispenser

This convenient fabric softener dispenser connects to the agitator and saves you from manually adding fabric softener during the rinse cycle.

Dryer vent lint brush Drying rack

All-purpose appliance cleaner

Laundry supply storage cart

Accessories

This washer does not include inlet water hoses. See Installation Instructions for installation accessories.

USING LESS WATER AND ENERGY

This washer is designed to use less water and energy, and complies with all 2015 energy standards. Wash cycles with controlled temperatures are designed to maintain cleaning performance while using less water and energy compared to older traditional washers. As a result, water levels will be lower, and hot and warm wash temperatures may not be as warm as you are used to.

Traditional washer

Reduced water washer

CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW

Maintain good airow:

■

Clean your lint screen before each load.

■

Replace plastic or foil vent material with 4" (102 mm) diameter heavy, rigid vent material.

■

Use the shortest length of vent possible.

■

Use no more than four 90° elbows in a vent system; each bend and curve reduces airow.

Good Better

Good airow

Along with heat, dryers require good airow to efciently dry laundry. Proper venting will reduce your drying times and improve your energy savings. See Installation Instructions.

The venting system attached to the dryer plays a big role in good airow.

Service calls caused by improper venting are not covered by the warranty and will be paid by the customer, regardless of who installed the dryer.

■

Remove lint and debris from the exhaust hood.

■

Remove lint from the entire length of the vent system at least every 2 years. When cleaning is complete, be sure to follow the Installation Instructions supplied with your dryer for nal product check.

■

Clear away items from the front of the dryer.

(102 mm)

Use Automatic cycles for better fabric care and energy savings

Use the Automatic Dry cycles to provide the most energy savings and enhanced fabric care from the dryer. During Automatic Dry cycles, drying air temperature or moisture level are sensed in the load. This sensing occurs throughout the drying cycle, and the dryer shuts off when the load reaches the selected dryness.

With Timed Drying, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to overdrying. Use Timed Drying for the occasional damp load that needs a little more drying time or when using the drying rack.

CONTROL PANEL AND FEATURES

STANDARD VENT MODELS

LONG VENT MODELS

1 2

Not all features and options are available on all models. Appearance may vary.

WASHER

WASH CYCLE KNOB

Use the Wash Cycle knob to select available cycles on your washer. Turn the knob to select a cycle for your laundry load.

See “Washer Cycle Guide” for detailed descriptions of cycles.

WASH TEMP

You may select a Wash Temperature based on the type of fabric and soils being washed. Use the warmest wash water safe for the fabric. Follow garment label instructions.

FABRIC SOFTENER

Set this knob to Yes when adding fabric softener to the fabric softener dispenser.

START/PAUSE

Press the START/PAUSE button to start the washer.

WASH STATUS INDICATOR LIGHTS

The Cycle Status lights show the progress of a cycle. At each stage of the process, you may notice sounds or pauses that are different from your previous washer.

SENSE FILL

When the Start/Pause button is pressed, the washer will ll and begin sensing to determine load size and balance.

Once sensing is complete, the washer will ll to the appropriate level for the detected load size and then begin the wash phase of the cycle.

NOTE: Sensing and wash phases will be paused by opening the unlocked lid. Close the lid to resume the cycle. If the lid is left open for more than 10 minutes, the washer will cancel the cycle and pump out the water. The lid will lock after the wash phase to begin the initial spinout and remain locked for the remainder of the cycle.

WASH

The washer will ll to the correct water level based on the load size. Certain cycles may agitate during the ll process to boost cleaning. You will hear the agitator rotate, followed by a pause lasting several seconds. When the wash cycle begins, you will hear the agitator increase speed. The motor sounds may change at different stages in the wash cycle while the washer performs different wash actions.

RINSE

Certain cycles use a spray rinse, which adds water to the tub while the basket spins. You may hear the motor turning on briey (short hum) to move the basket while lling.

DRAIN/SPIN

The washer spins the load at increasing speeds for proper water removal, based on the selected cycle.

DONE

Once the cycle is complete, this light will come on. Remove the load promptly for best results.

LID LOCK

The Lid Lock feature allows for higher spin speeds. When the Lid Lock light is lit, the lid is locked and cannot be opened without pausing the cycle. When the light is off, the lid can be opened.

To open the lid after it has been locked, press START/PAUSE. The lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at high speed. Press START/PAUSE again to resume the cycle.

DRYER

Gentleness

DRYER CYCLE KNOB

Use your Dryer Cycle knob to select available cycles on your dryer. Turn the knob to select a cycle for your laundry load. See “Dryer Cycle Guide” for detailed descriptions of cycles.

TIMED DRY

Will run the dryer for the specied time on the control. Drying time and temperature will depend on your dryer model.

NORMAL and DELICATE CYCLES

These cycles sense moisture in the load or air temperature and shut off when the load reaches the selected dryness level. They give the best drying in the shortest time. Drying time will vary based on fabric type, load size, and dryness setting.

AIR ONLY

This cycle will run the dryer without heat for the specied time on the control.

WASHER CYCLE GUIDE

Each cycle listing includes a performance chart rating its cleaning power, gentleness on items, and resource efciency. Not all cycles or options are available on all models. Refer to the cycle control knob on your washer.

Wash temperatures are selected using the Wash Temp knob. Cycles marked with “deep water wash” use a higher level of water.

For best performance:

■ Choose the cycle that best ts the load being washed.

■ Decrease or increase the maximum target water

temperature for any cycle.

■ Do not leave the washer lid open unattended once

the washer has started to ll.

START BUTTON

The Start button is used to start the dryer. The end-of-cycle signal produces an audible sound when the drying cycle is nished. Promptly removing clothes at the end of the cycle reduces wrinkling.

Items to wash: Cycle:

Cottons, linens, and mixed-garment loads

No-iron fabrics, cottons, permanent press, linens, synthetics

Machine-wash silks, hand-washed fabrics

Normal High and

Casuals High and

Delicates Low/Low Use this cycle to wash lightly soiled garments indicating “Machine

Load Size:

Wash/Spin

Speed: Cycle Details:

Use this cycle for normally soiled cottons and mixed-fabric loads.

Low/High

Low/Low

Efciency

Use this cycle to wash loads of no-iron fabrics such as sport shirts, blouses, casual business clothes, permanent press, and blends.

Cleaning

Efciency

Washable Silks” or “Gentle” cycle on the care label. Place small

Good

Cleaning

†

Good

†

Best

items in mesh garment bags before washing.

†Efcient use of resources, such as energy and water.

Cleaning

Efciency

Good

†

Best

IMPORTANT: Do not presoak items in your washer by lifting the lid or stopping the cycle. Failure to follow this instruction can result in property damage. If needed, presoak items in a small wash basin prior to loading the washer.

WASHER CYCLE GUIDE (CONT.)

Items to wash: Cycle:

Sturdy fabrics, colorfast items, towels, jeans

Colored cottons, linens, casual and mixed loads

Large items such as sheets, sleeping bags, small comforters, jackets, small washable rugs

Lightly soiled fabrics

Heavy Duty High/High Use this cycle for heavily soiled or sturdy items, or when using

Colors High/High Use this cycle for normally soiled colors and mixed-fabric loads.

Bulky Items

Quick Wash

Load

Size:

Wash/Spin

Speed: Cycle Details:

bleach.

Good

Cleaning

Gentleness

Efciency

Cleaning

†

Good

†

Low/Low Use this cycle to wash large items such as jackets and small

comforters. The washer will ll with enough water to wet down the load before the wash portion of the cycle begins, and uses a higher water level than other cycles.

Good

Cleaning

Gentleness

Efciency

†

High/High Use this cycle to quickly wash a small number of lightly soiled

items.

Cleaning

Gentleness

Efciency

Good

†

Best

Hand-washed garments or dripping-wet items

Drain

& Spin

N/A N/A/

High

This cycle uses a spin to shorten drying times for heavy fabrics or special-care items washed by hand. Use this cycle to drain washer after cancelling a cycle or completing a cycle after a power failure.

No clothes in washer

Clean

Washer

with

affresh

N/A Low/

N/A

Use this cycle every 30 washes to keep the inside of your washer fresh and clean. This cycle uses a higher water level. Use with affresh® washer cleaner tablet or regular liquid chlorine bleach to thoroughly clean the inside of your washer. This cycle should not be interrupted. See “Washer Care.” IMPORTANT: Do not place garments or other items in the washer during the Clean Washer with affresh® cycle. Use this cycle with an empty wash tub. Do not use thickened, easy-pour, or no-splash bleach when running the Clean Washer with affresh® cycle as excess suds may occur. See “Washer Care” in “Washer/ Dryer Maintenance.”

†Efcient use of resources, such as energy and water.

DRYER CYCLE GUIDE – AUTOMATIC DRY CYCLES

Not all cycles and settings are available on all models. Both the Normal and Delicate cycles are automatic dry cycles.

They give the best drying in the shortest time. They sense moisture in the load or air temperature and shut off when the load reaches the selected dryness level. Drying time varies based on fabric type, load size, and dryness setting.

Select either the Normal or Delicate cycle based on the fabrics in your load. If you are unsure of the cycle to select for a load, select the Delicate cycle (lower temperature) rather than the Normal cycle (higher temperature).

WRINKLE SHIELD™ option (long vent models)

This feature will run after your drying cycle is complete. It periodically starts and stops the dryer, tumbling the load without heat to help avoid wrinkling.

Standard Vent Models Long Vent Models

Items to dry: Cycle: Available Options: Cycle Details:

Corduroys, work clothes Normal None Medium to large loads of mixed fabrics and items. Lingerie, blouses,

washable knit fabrics

NOTE: If loads do not seem as dry as you would like, select Very Dry next time you dry a similar load. If loads seem drier than you like, select Less Dry next time you dry a similar load.

Delicate None For gently drying delicate items.

DRYER CYCLE GUIDE – TIMED DRYING

Not all cycles and settings are available on all models. Will run the dryer for the selected time.

Items to dry: Cycle: Temperature: Available Options: Cycle Details:

Rubber, plastic, heat-sensitive fabrics

Heavy, bulky, or lightweight items

NOTE: Government energy certications for this model were based on the Timed Dry cycle with the Maximum drying temperature setting. The as-shipped defaults of Normal cycle, Less Dry, and the Wrinkle Shield™ option (when applicable) were not used.

Air Only No Heat Time Adjustment For airing out, refreshing, and loosening up

laundry without heating.

Timed Dry High Time Adjustment Completes drying if items are still damp.

USING YOUR WASHER

1. Sort and prepare your laundry

■ Empty pockets. Loose change, buttons, or any small object

can pass under the agitator and become trapped, causing unexpected sounds.

■ Sort items by recommended cycle, water temperature,

and colorfastness.

■ Separate heavily soiled items from lightly soiled.

■ Separate delicate items from sturdy fabrics.

■ Do not dry garments if stains remain after washing, because

heat can set stains into fabric.

■ Treat stains promptly.

■ Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

■ Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

■ When washing waterproof or water-resistant items, load evenly.

■ Use mesh garment bags to help avoid tangling when washing

delicate or small items.

■ Turn knits inside out to avoid pilling. Separate lint-takers from

lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions to avoid damage to your garments.

2. Add laundry products

Add a measured amount of HE detergent or single-dose laundry packet into the basket.

If using Oxi-type boosters, color-safe bleach, or fabric softener crystals, add to the bottom of the washer basket before adding clothes.

IMPORTANT: Use only High Efciency detergents. The package will be marked “HE” or “High Efciency.” Using non-HE detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component malfunction and, over time, buildup of mold or mildew. HE detergents should be low-sudsing and quick-dispersing to produce the right amount of suds for the best performance. They should hold soil in suspension so it is not redeposited onto clean clothes. Not all detergents labeled as High Efciency are identical in formulation and their ability to reduce suds. For example, natural, organic, or homemade HE detergents may generate a high level of suds.

NOTE: Follow the manufacturer’s instructions to determine the amount of laundry products to use.

3. Load laundry into washer

Liquid

Chlorine Bleach

5. Add fabric softener to dispenser

Load garments in loose heaps evenly around basket wall. For best results, do not pack the load tightly. Do not wrap large items such as sheets around the agitator; load them in loose piles around the sides of the basket. Try mixing different-sized items to reduce tangling.

IMPORTANT: Do not tightly pack or force items into washer. Items need to move freely for best cleaning and to reduce wrinkling and tangling.

4. Add liquid chlorine bleach

to dispenser

Pour a measured amount of liquid fabric softener into dispenser; always follow manufacturer’s directions for correct amount of fabric softener based on your load size.

Dilute liquid fabric softener by lling the dispenser with warm water until liquid reaches the underside of the rim. See max ll line arrows. Do not overll.

Adding Liquid Fabric Softener Manually to Wash Load

During the nal rinse, wait until the washer has completed lling and press the START/PAUSE button to pause the washer. Lift the lid and add the measured recommended amount of liquid fabric softener. Do not allow liquid fabric softener to spill, splash, drip, or run into the basket or on load. Do not use more than the recommended amount. Close the lid and press the START/ PAUSE button again to start the washer.

MAX FILL

6. Select cycle

Do not overll, dilute, or use more than 1 cup (236 mL). Do not use color-safe bleach or Oxi products in the same cycle with liquid chlorine bleach.

Turn cycle knob to choose your wash cycle. For more information, see “Washer Cycle Guide.”

7. Select wash temperature

8. Select fabric softener (if desired)

Select the desired wash temperature by turning the Wash Temp knob to the desired setting. All rinses are cold.

NOTE: Always read and follow fabric care label instructions to avoid damage to your garments.

Wash Temp Suggested Fabrics Hot

Some cold water is added to save energy. This will be cooler than your hot water heater setting.

Warm

Some cold water will be added, so this will be cooler than what your previous washer provided.

Cool

Some warm water may be added to assist in soil removal and to help dissolve detergents. Cool is slightly warmer than cold.

Cold

This is the temperature from your faucet. Warm water may be added to assist in soil removal and to help dissolve detergents.

Tap Cold

This is the temperature from your faucet.

Whites and pastels Durable garments Heavy soils

Bright colors Moderate to light soils

Colors that bleed or fade Light soils

Dark colors that bleed or fade Light soils

Set this knob to Yes when adding fabric softener to the fabric softener dispenser.

9. Press START/PAUSE to begin

wash cycle

Press the START/PAUSE button to start the wash cycle. When the cycle has nished, the Done indicator will light. Promptly remove garments after cycle has completed to avoid odor, reduce wrinkling, and prevent rusting of metal hooks, zippers, and snaps.

Adding garment(s)

If you need to open the lid to add one or two missed garments: Press the START/PAUSE button. The lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at high speed. Add garments, close lid, and press the START/PAUSE button again to restart the cycle.

NOTE: Washer will not ll with the lid open. IMPORTANT: If lid is left open for more than 10 minutes, the

water will pump out automatically.

Manual Soak

If you would like to manually soak your garments at any time during the wash portion of the cycle, press the START/ PAUSE button and leave the lid closed. Once your desired soak time has elapsed, press the START/PAUSE button again to continue the cycle. As long as the lid remains closed, your soak time can be longer than 10 minutes. However, if the lid is opened during the soak and remains open for more than 10 minutes, the water will pump out automatically.

USING YOUR DRYER

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the Important Safety Instructions before operating this dryer.

Before using your dryer, wipe the dryer drum with a damp cloth to remove dust from storing and shipping.

1. Clean the lint screen

3. Select cycle

Clean the lint screen before each load. Pull the lint screen straight up. Roll lint off the screen with your

ngers. Push the lint screen rmly back into place. Do not rinse or wash screen to remove lint. For additional

cleaning information, see “Cleaning the lint screen.”

2. Load the dryer

Place laundry in the dryer. Close the door. NOTE: Your model may have a different door than the

one shown. Do not tightly pack the dryer; clothes should be able to

tumble freely.

Select the desired cycle for your load. See “Dryer Cycle Guide” for more information about each cycle.

Normal and Delicate Cycles

You can select a different dryness level, depending on your load, by turning the knob to the desired dryness level.

Selecting Very Dry or Less Dry automatically adjusts the dryness level at which the dryer will shut off. Once a dryness level is set, it cannot be changed without stopping the cycle.

These automatic dry cycles give the best drying in the shortest time. Drying time varies based on fabric type, load size, and dryness setting.

NOTE: Very Dry removes more load moisture. Less Dry removes less moisture and is used for loads you may want to put on a hanger to complete drying.

4. Press START button to begin cycle

Press and hold the START button to begin the cycle. Promptly remove garments after cycle has completed

to reduce wrinkling.

ADDITIONAL FEATURES

USING THE DRYING RACK

To obtain a drying rack for your dryer, see the “Accessories” section. Remove and discard any packing material before use.

Use the drying rack for items that you do not want to tumble dry, such as sweaters and tennis shoes. When you use the drying rack, the drum continues to turn, but the rack remains stationary.

The drying rack is intended for use with the Timed Dry cycles only. The drying rack cannot be used with Automatic Dry cycles.

To use the drying rack:

IMPORTANT: Do not remove the lint screen.

1. Open dryer door.

2. Align the two hooks on the front of the drying rack with

the holes in the dryer door opening and press down fully into holes. Rest the rear support on the dryer back ledge.

3. Place wet items on top of the drying rack. Allow space

around items for air to circulate. The drying rack does not move, but the drum will rotate. Make sure items do not hang over the edges or between drying rack grille.

4. Close the door.

5. Select a Timed Dry/Air Only or Low Temperature cycle.

Items containing foam, rubber, or plastic must be dried on a clothesline or by using the Air Only setting.

6. Start the dryer. NOTE: Check the lint screen and remove any lint accumulated

from items dried on the drying rack after the cycle is nished.

WASHER/DRYER MAINTENANCE

WATER INLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement on the label with a permanent marker.

WASHER CARE

Recommendations to Help Keep Your Washer Clean and Performing at Its Best

1. Always use High Efciency detergents and follow the

detergent manufacturer’s instructions regarding the amount of detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better job of controlling the rate at which soils and detergent accumulate.

3. Always leave the washer lid open between uses to help

dry out the washer and prevent the buildup of odor-causing residue.

Cleaning Your Top-Loading Washer

Read these instructions completely before beginning the routine cleaning processes recommended below. This Washer Maintenance Procedure should be performed, at a minimum, once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions provided above and use this recommended monthly cleaning procedure:

Recommended Cycle for Cleaning the Washer

Refer to the “Cycle Guide” for the optimal cycle for cleaning the inside of the washer. Use this cycle with affresh® Washer Cleaner or liquid chlorine bleach as described below.

Begin procedure affresh® Washer Cleaner Cycle procedure (Recommended

for Best Performance):

a. Open the washer lid and remove any clothing or items. b. Use an affresh® Machine Cleaning Wipe or a soft, damp

cloth or sponge to clean the inside of the door.

c. Place an affesh® Washer Cleaner tablet in the bottom

of the washer basket.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer lid. f. Select the Clean Washer with affresh® cycle. g. Press and hold START/PAUSE to begin the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press the START/PAUSE button once. After the cycle has stopped, run a Quick Wash cycle to rinse cleaner from washer.

WASHER CARE (cont.)

Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing

or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach

to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage over time.

c. Close the washer lid. d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Select the Clean Washer with affresh® cycle. f. Press and hold START/PAUSE to begin the cycle.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, press the START/PAUSE button once. After the cycle has stopped, run a Quick Wash cycle to rinse cleaner from washer.

Description of Clean Washer with affresh® Cycle Operation:

1. The Clean Washer with affresh® cycle will determine

whether clothing or other items are in the washer.

2. If no items are detected in the washer, it will proceed with

the cycle.

After the cycle is complete, leave the lid open to allow for better ventilation and drying of the washer interior.

Cleaning the liquid fabric softener dispenser (on some models)

1. Remove dispenser by grasping top with both hands

and squeezing, while pushing upward with thumbs.

2. Rinse dispenser under warm water or wipe the surfaces

with an affresh and towel dry either before or after you run the Clean Washer with affresh® cycle. Use an all-purpose surface cleaner, if needed.

3. Replace the dispenser.

NOTE: To avoid damage to the washer or clothing,

do not wash clothes with the liquid fabric softener dispenser removed.

Cleaning the bleach dispenser (on some models)

Wipe the inside of the bleach dispenser with an affresh® Machine Cleaning Wipe or a clean, damp cloth. Use an all-purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use an affresh® Machine Cleaning Wipe or a soft, damp cloth or sponge to wipe away any spills. Use an affresh® Machine Cleaning Wipe or only mild soaps or cleaners when cleaning external washer surfaces.

IMPORTANT: To avoid damaging the washer’s nish, do not use abrasive products.

Machine Cleaning Wipe or a damp cloth

CLEANING THE WASHER/DRYER LOCATION

CLEANING THE LINT SCREEN

Keep washer/dryer area clear and free from items that would block the airow for proper washer/dryer operation. This includes clearing piles of laundry in front of the washer/ dryer.

CLEANING THE DRYER INTERIOR

To clean dryer drum

1. Apply a liquid, nonammable household cleaner to the

stained area of the drum and rub with a soft cloth until stain is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry the drum.

NOTE: Garments that contain loose dyes, such as denim

blue jeans or brightly colored cotton items, may discolor the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry these items inside out to avoid drum staining.

REMOVING ACCUMULATED LINT

From inside the dryer cabinet

Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning should be done by a qualied servicer.

From the exhaust vent

Lint should be removed every 2 years, or more often, depending on dryer usage.

Every load cleaning

A screen blocked by lint can increase drying time. The lint screen is located in the door opening of the dryer.

To clean:

1. Pull the lint screen straight up. Roll lint off the screen

with your ngers.

Do not rinse or wash the screen to remove lint. Wet lint

is hard to remove.

2. Push the lint screen rmly back into place. IMPORTANT:

■

Do not run the dryer with the lint screen loose, damaged, blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics.

■

If lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. See “Venting Requirements” in the Installation Instructions.

As-needed cleaning

Laundry detergent and fabric softener residue can build up on the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely dry. The screen is probably clogged if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months, or more frequently, if it becomes clogged due to a residue buildup.

To wash:

1. Roll lint off the screen with your ngers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel.

Reinstall screen in dryer.

CHANGING THE DRUM LIGHT (on some models)

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the

back wall of the dryer. Using a Phillips-head screwdriver, remove the screw located in the lower right-hand corner of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with

a 10-watt appliance bulb only. Replace the cover and secure with the screw.

4. Plug into a grounded outlet or reconnect power.

VACATION, STORAGE, AND MOVING CARE

Non-Use or Storage Care

Operate your washer/dryer only when you are at home. If you will be on vacation or not using your washer/dryer for an extended period of time, you should:

1. Unplug washer/dryer or disconnect power.

2. Turn off water supply to washer, to avoid ooding due

to water pressure surge.

3. For gas dryers only: Close shut-off valve to gas supply line.

4. Clean lint screen. See “Cleaning the Lint Screen”.

Moving Care

For power supply cord-connected washer/dryers:

1. Unplug the power supply cord.

2. Make sure leveling legs are secure in washer/dryer base.

3. Continue with “For all washer/dryers” in next column.

VACATION, STORAGE, AND MOVING CARE (cont.)

For direct-wired washer/dryers:

1. Turn off power at fuse or breaker box.

2. Disconnect wiring.

3. Make sure leveling legs are secure in washer/dryer base.

4. Continue with “For all washer/dryers” below.

For gas washer/dryers:

1. Unplug or disconnect power to washer/dryer.

2. Close shut-off valve in gas supply line.

3. Disconnect gas supply line pipe and remove ttings

attached to dryer pipe.

4. Cap the open fuel supply line.

5. Make sure leveling legs are secure in washer/dryer base.

6. Continue with “For all washer/dryers” below.

For all washer/dryers:

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer/dryer will be moved during freezing weather,

follow “Winter Storage Care” directions before moving.

3. Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain hose from back of washer.

4. Place inlet hoses and drain hose inside washer basket.

5. Drape power cord over edge and into washer basket.

6. Place packing tray from original shipping materials

back inside washer/dryer. If you do not have packing tray, place heavy blankets or towels into basket opening. Close lids/doors and place tape over lids/doors and down front of washer/dryer. Keep lids/doors taped until washer/dryer is placed in new location.

+ 42 hidden pages