Whirlpool MGT3800XW2, 7MWGT3300EQ0, MGT3800XW3, MGT3800XW1, WGT3300XQ3 Installation Guide
...
27" (69 CM) GAS WASHER/DRYER
INSTALLATION INSTRUCTIONS
INSTRUCTIONS POUR UINSTALLATION DE LA
St CHEUSE A GAZ DE 27" (69 CM)
Table of Contents
WASHER/DRYER SAFETY .......................................................... 1
iNSTALLATiON REQUIREMENTS ............................................... 4
Tools and Parts ..................................................................... 4
LOCATION REQUIREMENTS ...................................................... 6
DIMENSIONS/CLEARANCES ..................................................... 7
DRAIN SYSTEM ........................................................................... 8
ELECTRICAL REQUIREMENTS .................................................. 9
GAS SUPPLY REQUIREMENTS .................................................. 9
REMOVE SHiPPiNG STRAP ...................................................... 11
iNSTALL LEVELING LEGS ......................................................... 11
VENTING ..................................................................................... 12
Venting Requirements ........................................................ 12
Plan Vent System ................................................................ 13
Install Vent System ............................................................. 14
CONNECT DRAIN HOSE ........................................................... 15
CONNECT iNLET HOSES .......................................................... 16
MAKE GAS CONNECTION ........................................................ 18
CONNECT VENT ........................................................................ 18
LEVEL WASHER/DRYER ........................................................... 19
COMPLETE iNSTALLATiON CHECKLIST ................................ 20
SLeCURITle DE LA LAVEUSF-=/SLeCHEUSE ................................ 21
EXIGENCES D'INSTALLATION ................................................. 24
Outillage et pi_ces ............................................................. 24
EXIGENCES D'EMPLACEMENT .............................................. 26
DIMENSIONS/DISTANCES DE DleGAGEMENT ....................... 27
SYSTEME DE VIDANGE ............................................................ 28
SPECIFICATIONS leLECTRIQUES ............................................ 29
SPECIFICATIONS DE UALIMENTATION EN GAZ ................... 29
ENLEVER LA SANGLE D'EXPEDITION .................................... 31
iNSTALLATiON DES PIEDS DE NIVELLEMENT ...................... 31
leVACUATION ............................................................................. 32
E×igences concernant I'_vacuation ................................. 32
Planification du syst_me d'6vacuation ............................ 33
Installation du conduit d'_vacuation ................................ 34
RACCORDEMENT DU TUYAU DE VIDANGE ........................... 35
RACCORDEMENT DES TUYAUX D'ARRIVLeE D'EAU ............. 36
RACCORDEMENT A LA CANALISATION DE GAZ .................. 37
RACCORDEMENT DU CONDUIT DqeVACUATION ................. 38
_:TABLISSEMENT DE L'APLOMB
DE LA LAVEUS_'SECHEUSE .................................................... 39
LISTE DE VERIFICATION POUR UACHEVEMENT
DE UINSTALLATION .................................................................. 40
Table des mati_res
LAVEUSE/
iNSTALLATiON NOTES NOTES CONCERNANT L'INSTALLATION
Date of purchase:
Date of installation:
Installer:
Model number:
Serial number:
Date d'achat:
Date d'installation:
Installateur:
Num_ro de module:
Num_ro de s_rie:
WASHER/DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be kifled or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
W10356101C
WASHER/DRYER SAFETY
WARNING - ofFifo,,
- Clothes dryer installation must be performed by a qualified installer.
- Install the clothes dryer according to the manufacturer's instructions and local codes.
- Do not install a clothes dryer with flexible plastic venting materials or flexible metal
(foil type) duct. if flexible metal duct is installed, it must be of a specific type identified
by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting
materials are known to collapse, be easily crushed, and trap lint. These conditions will
obstruct clothes dryer airflow and increase the risk of fire.
- To reduce the risk of severe injury or death, follow all installation instructions.
- Save these instructions.
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO iF YOU SMELL GAS:
®Do not try to light any appliance.
o Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building, or area of all occupants.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
= if you cannot reach your gas supplier, call the fire department.
- installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
2
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the "What to do if you smell gas" instructions.
In the State of Massachusetts, the following installation instructions apply:
[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
[] If using a ball valve, it shall be a T-handle type.
[] A flexible gas connector, when used, must not exceed 3 feet.
IMPORTANT." The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1iNFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.
IMPORTANT SAFETY INSTRUCTIONS
WARNINGt, To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic
precautions, including the following:
[] Read all instructions before using the washer/dryer.
[] Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire.
[] Do not wash or dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry-cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Do not allow children to play on or in the washer/dryer.
Close supervision of children is necessary when the
washer/dryer is used near children.
[] Before the washer/dryer is removed from service or
discarded, remove the doors to the washer/dryer
compartments.
[] Do not reach into the washer/dryer ifthe tub, agitator or
drum is moving.
[] Do not install or store the washer/dryer where it will be
exposed to the weather.
[] Do not tamper with controls.
[] Clean dryer lint screen before or after each load.
[] Under certain conditions, hydrogen gas may be produced
in a hot water system that has not been used for 2 weeks
or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using
the washing machine, turn on all hot water faucets and let
the water flow from each for several minutes. This will
release any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this time.
[] Do not repair or replace any part of the washer/dryer or
attempt any servicing unless specifically recommended in
this Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
[] Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
[] Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
[] Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
[] The interior of the machine and dryer exhaust vent should
be cleaned periodically by qualified service personnel
[] See "Electrical Requirements" section of the Installation
Instructions booklet for grounding instructions.
SAVE THESE INSTRUCTIONS
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather required tools and parts before starting installation.
Tools needed:
Flat-blade screwdriver
Adjustable or open-end
wrench 9/16" (14 mm)
4" rain
(102 rnrn)_
Wood block
Pliers that open to 1%6"
(39.5 mm)
#2 Phillips screwdriver
@
Level
Ruler or measuring tape
Adjustable wrench that
opens to 1" (25 mm) or
hex-head socket wrench
Tin snips (new vent
installations)
Tools needed for gas installations:
8" or 10" pipe wrench
Pipe-joint compound
resistant to LP gas
Optional tools:
8" or 10" adjustable wrench
(for gas connections)
1/4" nut driver Wire stripper
(recommended)
Caulking gun and compound
(new vent installations)
4
Utility knife
Flashlight
Parts supplied:
NOTE: Remove parts package from the washer basket.
Check that all parts were included.
Front leveling feet with nuts (2)
Bucket
Shipping strap (Not in parts bag.
See "Remove Shipping Strap.")
9
Drain hose
Silver double-wire hose clamp
Parts needed: (Not supplied with washer/dryer)
[] Vent clamps
[] Vent elbows and ductwork
[] Mobile Home Installation Kit
(Part Number 346764)
[] Metal exhaust system hardware
Inlet hoses with
flat washers
Check local codes, electrical supply and venting, and read
"Electrical Requirements" and "Venting Requirements" before
purchasing parts. Mobile home installations require metal
exhaust system hardware available for purchase from the
dealer from whom you purchased your washer/dryer. For
further information, please reference the "Assistance or
Service" section of the Washer/Dryer Use and Care Guide.
Optional equipment: (Not supplied with washer/dryer)
Refer to your Use and Care Guide for information about
accessories available for your washer/dryer.
Alternate parts: (Not supplied with washer/dryer)
Your installation may require additional parts. To order, please
refer to toll-free numbers on back page of your Use and Care
Guide.
If you have:
Overhead sewer
Floor drain
1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm)
Laundry tub or
standpipe taller than
96" (2.4 m)
Drain hose too short
Lint clogged drain Drain Protector Part Number 367031,
Water faucets
beyond reach
of fill hoses
You will need:
Standard 20 gal. (76 L) 39" (990 mm)
tall Drain Tub or Utility Sink, Sump
Pump and Connectors (available from
local plumbing suppliers)
Siphon break Part Number 285320,
Additional Drain Hose Part Number
285702, and Connector Kit Part
Number 285442
diameter Standpipe Adapter
Part Number 3363920,
Connector Kit Part Number 285835
Sump pump system (if not already
available)
Extension Drain Hose
Part Number 285863,
Connector Kit Part Number 285835
Connector Kit Part Number 285835
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
LOCATION REQUIREMENTS
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not install in a garage.
Failure to do so can result in death, explosion, or fire.
Select proper location for your washer to improve performance
and minimize noise and possible "washer walk." Install your
washer in a basement, laundry room, closet, or recessed area.
You will need:
[] A location that allows for proper exhaust installation.
A gas washer/dryer must be exhausted to the outdoors.
See "Venting Requirements."
[] A grounded electrical outlet located within 2 ft (610 mm) of
either side of the washer/dryer. See "Electrical Requirements."
[] A separate 15- or 20-amp circuit.
[] A sturdy floor to support the washer/dryer weight (washer/
dryer, water, and load) of 500 Ibs (226.8 kg).
[] A level floor with a maximum slope of 1" (25 mm) under entire
washer/dryer. Clothes may not tumble properly and automatic
sensor cycles may not operate correctly if washer/dryer is not
level. Installing on carpet is not recommended.
[] A water heater set to deliver 120°F (49°C) water to the washer.
[] Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of 5-100 psi
(34.5-689.6 kPa).
The washer/dryer must not be installed or stored in an area where
it will be exposed to water and/or weather.
Do not operate your washer in temperatures at or below 32°F
(0°C). Some water can remain in the washer and can cause
damage in low temperatures. See "Washer/Dryer Care" in the
Washer/Dryer Use and Care Guide for winterizing information.
Do not operate your dryer at temperatures below 45°F (7°C). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.
Check code requirements. Some codes limit, or do not permit,
installation of the washer/dryer in garages, closets, mobile
homes, or sleeping quarters. Contact your local building
inspector.
Recessed area or closet installation
48 in.2
(310 cm2)
Front
View
Closet
door
3"
(76mr
O
24 in.2
(155 cm2)
The spacing dimensions above are recommended for this
washer/dryer. This washer/dryer has been tested for spacing of
0" (0 mm) clearance on the sides. Recommended spacing should
be considered for the following reasons:
[] Additional spacing should be considered for ease of
installation and servicing.
[] Additional clearances might be required for wall, door, and
floor moldings.
[] Additional spacing on all sides of the washer/dryer is
recommended to reduce noise transfer.
[] For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
Mobile home = additional installation requirements
This washer/dryer is suitable for mobile home installations.
The installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280) or the Canadian
Manufactured Home Standard, CAN/CSA-Z240 MH.
Mobile home installations require:
[] Metal exhaust system hardware, which is available for
purchase from your dealer.
[] Mobile Home Installation Kit Part Number 346764. See "Tools
and Parts" section for information on ordering.
[] Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
6
DIMENSIONS/CLEARANCES
Dimensions
Front View
Side View
27%" -_
(892 ram)
OooooQ
8]
713/4"
(182'; mini
1 "
(25 ram)
p 73/4" _,_
(680 ram) I
2!3 ram) _ 26"
]
]
Clearances
Side Clearances (recommended/minimum)
(.3 0 0 c, 0 \s
1"/0"_ _"-' _"-' _ 1"/O"
(25 mm/O ram) (25 mra/Oram)
Front/Back/Top Clearances
\
(305 ram)
12"
883/4"
(1670 ram)
Back View
41%"
tara)
32V8"
(8!6 ram)
(279 ram)
z _:m
_32"' -_
(8!3 ram)
27V4"-_.
(892 ram)
-(356 ram)
T
34"
(864 ram)
1 "
(25 rara)
14"
t t
25"
71s/4"
(1822 ram)
28t/2"
1II _ _ _ _5"
(25 mm) (127 ram)
(Closet)
(1,04 i
(8351rara) (8731rara)
1 "
(25 ram)
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe,
floor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than 96"
(2.4 m) from bottom of washer/dryer. If you must install higher
than 96" (2.4 m), you will need a sump pump system.
Wall standpipe drain system
See requirements for floor standpipe drain system.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285385), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. To order, please see toll-free phone
numbers in your Use and Care Guide. Minimum siphon break:
28" (710 mm) from bottom of washer/dryer. (Additional hoses
may be needed.)
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be
at least 39" (990 mm) above floor; install no higher than 96"
(2.4 m) from bottom of washer/dryer.
IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with shipping strap.
8
ELECTRICAL REQUIREMENTS
GAS SUPPLY REQUIREMENTS
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
[] This washer/dryer is equipped with a power supply cord
having a 3-prong grounding plug.
[] To minimize possible shock hazard, the cord must be plugged
into a mating, 3-prong, grounding-type outlet, grounded in
accordance with local codes and ordinances. If a mating outlet
is not available, it is the personal responsibility and obligation
of the customer to have the properly grounded outlet installed
by a qualified electrician.
[] If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that
the ground path is adequate.
[] Do not ground to a gas pipe.
[] Check with a qualified electrician if you are not sure the
washer is properly grounded.
[]
Do not have a fuse in the neutral or ground circuit.
[]
120 Volt, 60 Hz, AC only, 15- or 20- amp fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is also recommended that a separate
circuit serving only this washer/dryer be provided.
GROUNDING INSTRUCTIONS
[] For a grounded, cord-connected washer/dryer:
This washer/dryer must be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for
electric current. This washer/dryer is equipped with a cord
having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with
all local codes and ordinances.
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut=off valve.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (330 ram) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
GAS TYPE
Natural Gas:
This washer/dryer is equipped for use with Natural gas. It is
design-certified by CSA international for LP (propane or butane)
gases with appropriate conversion.
[] Your washer/dryer must have the correct burner for the type of
gas in your home. Burner information is located on the rating
plate in the door well of your dryer. If this information does not
agree with the type of gas available, contact your dealer or call
the phone numbers referenced in the "Assistance or Service"
section of your Use and Care Guide.
LP Gas Conversion:
iMPORTANT: Conversion must be made by a qualified
technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting your gas company.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the
washer/dryer is properly grounded. Do not modify the plug
provided with the washer/dryer: if it will not fit the outlet,
have a proper outlet installed by a qualified electrician.
SAVE THESE INSTRUCTIONS
GAS SUPPLY REQUIREMENTS
GAS SUPPLY LINE
[] Must include 1/8" NPT minimum plugged tapping accessible
for test gauge connection, immediately upstream of the gas
connection to the washer/dryer. See illustration below.
[] 1/2" IPS pipe is recommended.
[] Must include shut-off valve:
in the U.S.Ao:
An individual manual shut-off valve must be installed within
six (6) ft. (1.8 m) of the washer/dryer in accordance with the
National Fuel Gas Code, ANSi Z223.1. The location should
be easy to reach for opening and closing.
In Canada:
An individual manual shut-off valve must be installed in
accordance with the B149.1, Natural Gas and Propane
Installation Code. It is recommended that an individual
manual shut-off valve be installed within six (6) ft. (1.8 m)
of the washer/dryer. The location should be easy to reach
for opening and closing.
E
C \
B
A. 3/8" flexible gas connector
B. 3/8" pipe to flare adapter fitting
C. 1/8" NPT minimum plugged tapping
D. 1/2" NPT gas supply line
E. Gas shut-off valve.
This washer/dryer is equipped with its own permanent,
flexible gas connector, design-certified by CSA International,
for connecting the washer/dryer to the gas supply line.
0 _D _
DRYER GAS CONNECTION
Option 1
Rigid gas supply line:
[] Connect your washer/dryer to the rigid gas supply line using
an elbow and a 3/8" flare x 3/8" NPT adapter fitting between
the stainless steel gas connector and the washer/dryer gas
pipe, as needed to prevent kinking.
Option 2
Approved aluminum or copper tubing:
[] 3/8" approved aluminum or copper tubing is acceptable for
lengths under 20 ft. (6.1 m) if local codes and gas supplier
permit.
[] If you are using natural gas, do not use copper tubing.
[] Lengths over 20 ft. (6.1 m) should use larger tubing and
a different size adapter fitting.
[] If your washer/dryer has been converted to use LP gas, 3/8"
LP compatible copper tubing can be used. If the total length
of the supply line is more than 20 ft. (6.1 m), use larger pipe.
NOTE: Pipe-joint compounds that resist the action of LP gas
must be used. Do not use TEFLON_'*_ttape.
GAS SUPPLY CONNECTION REQUIREMENTS
[] Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting
between the flexible gas connector and the washer/dryer gas
pipe, as needed, to avoid kinking.
[] Use only pipe-joint compound. Do not use TEFLON _'*_ttape.
BURNER INPUT REQUIREMENTS
Elevations up to 10,000 ft (3,048 meters):
[] The design of this washer/dryer is certified by CSA
International for use at altitudes up to 10,000 ft (3,048 m)
above sea level at the Btu rating indicated on the model/serial
number plate. Burner input adjustments are not required when
the washer/dryer isoperated up to this elevation.
Elevations above 10,000 ft (3,048 meters):
[] When installed above 10,000 ft. (3,048 m) a 4% reduction of
the burner Btu rating shown on the model/serial number plate
is required for each 1,000 ft. (305 m) increase in elevation.
Gas supply pressure testing
[] The washer/dryer must be disconnected from the gas supply
piping system during pressure testing at pressures greater
than 1/2 psi.
10
Flexible gas connector
1®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.
REMOVE SHIPPING STRAP
INSTALL LEVELING LEGS
Excessive Weight Hazard
Use two or more people to move and install washer/dryer.
Failure to do so can result in back or other injury.
To avoid floor damage, set washer/dryer onto cardboard before
moving across floor. Move washer/dryer close to its final location.
Remove strap, hang tag, and pin
Do not cut yellow strap. Pull yellow strap firmly, until completely
removed from washer/dryer. There should be 2 cotter pins on
the end of the shipping strap. Remove the hang tag and pin
from the vent pipe.
Excessive Weight Hazard
Use two or more people to move and install washer/dryer.
Failure to do so can result in back or other injury,
1. Prepare to install leveling feet
Prop up the front of the washer/dryer
about 4" (102 mm) with a wood block
or similar object that will support the
weight of the washer/dryer. Then screw the Iocknut onto each
foot to within 1" (25 mm) of the foot base.
Tilt the washer/dryer forward. Move each of the 2 rear legs in
an up-down motion to check the self-adjusting leveling legs
for free movement. This is required for proper leveling. Gently
lower the washer/dryer to the floor.
Cut shipping strap
2, Install front leveling feet
Screw the feet into the threaded holes at
the front corners of the washer/dryer until
the jam nuts touch the washer.
NOTE: Do not tighten the nuts until the washer/dryer is level.
Tilt the washer/dryer back and remove the wood block. Gently
lower the washer/dryer to the floor.
Cut the shipping strap about 16" (406 mm) from the plug end.
Look for the words "CUT HERE." Discard end with cotter pins.
You will use the remaining piece of shipping strap to secure
the drain hose.
11
VENTING
Venting Requirements
Fire Hazard
Use a heavy metal vent,
Do not use a plastic vent.
Do not use a metal foi vent,
Failure to follow these instructions can result in death
or fire.
WARNING: To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
Dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, attic, crawlspace, or a concealed space
of a building. Only rigid or flexible metal vent shall be used for
exhausting.
]
(102 ram)
Exhaust hoods:
[] Must be at least 12" (305 ram) from ground or any object that
may obstruct exhaust (such as flowers, rocks, bushes, or
snow).
Recommended Styles:
Louvered hood
Acceptable Style:
Angled hood
Elbows:
[] 45° elbows provide better airflow than 90° elbows.
Box hood
Bet
{
4" (102 mm) heavy metal exhaust vent
[] Only a 4" (102 mm) heavy metal exhaust vent and clamps may
be used.
[] Do not use plastic or metal foil vent.
Rigid metal vent:
[] Recommended for best drying performance and to avoid
crushing and kinking.
Flexible metal vent: (Acceptable only ifaccessible to clean)
[] Must be fully extended and supported in final dryer location.
[] Remove excess to avoid sagging and kinking that may result
in reduced airflow and poor performance.
[] Do not install in enclosed walls, ceilings, or floors.
[] The total length should not exceed 73/4ft. (2.4 m).
NOTE: If using an existing vent system, clean lint from entire
length of the system and make sure exhaust hood is not
plugged with lint. Replace plastic or metal foil vents with rigid
metal or flexible metal vents. Review "Vent System Chart" and,
if necessary, modify existing vent system to achieve best drying
performance.
Clamps:
[] Use clamps to seal all joints.
[] Exhaust vent must not be connected or secured with screws
or other fastening devices that extend into interior of duct
and catch lint. Do not use duct tape.
improper venting can cause moisture and lint to colect
indoors, which may result in:
[] Moisture damage to woodwork, furniture, paint, wallpaper,
carpets, etc.
[] Housecleaning problems and health problems.
12
See "Venting Kits" for more information.
Loading...