Whirlpool WFW9550WW Owners Manual
®
r
®
FRONT-LOADING
AUTOMATIC WASHER
Use & Care Guide
For questions about features, operation/performance,
parts, accessories, or service call: 1-800-253-1301
In Canada, call: 1-800-807-6777
www.whirlpool.com or www.whirlpool.ca
or visit our website at
LAVEUSE
Certified to Sanitize
Homologué pour assaini
AUTOMATIQUE À
CHARGEMENT FRONTAL
Guide d'utilisation et d'entretien
Au Canada, pour assistance, installation ou service, composez le :
ou visitez notre site Internet à www.whirlpool.ca
Table of Contents/Table des matières.................. 2
Designed to use only HE High Efficiency Detergent
Conçue pour l'utilisation d'un détergent haute efficacité
seulement
1-800-807-6777
W10251899D
TABLE OF CONTENTS
TABLE DES MATIÈRES
WASHER SAFETY .........................................................................3
INSTALLATION REQUIREMENTS ................................................4
Tools and Parts ............................................................................4
Options......................................................................................... 4
Location Requirements................................................................5
Drain System................................................................................6
Electrical Requirements ...............................................................7
INSTALLATION INSTRUCTIONS ..................................................7
Remove Transport System ..........................................................7
Connect the Inlet Hoses...............................................................8
Connect the Drain Hose...............................................................8
Secure the Drain Hose.................................................................9
Level the Washer..........................................................................9
Complete Installation ...................................................................9
FEATURES AND BENEFITS ........................................................10
WASHER USE...............................................................................11
Starting Your Washer.................................................................11
Using the Proper Detergent .......................................................11
Using the Dispenser...................................................................12
Pausing or Restarting.................................................................13
Changing Cycles, Options, and Modifiers.................................13
Status Lights ..............................................................................13
Cycles.........................................................................................14
Normal Washer Sounds.............................................................15
Options.......................................................................................16
Modifiers.....................................................................................16
Laundry Guide............................................................................17
LAUNDRY TIPS ............................................................................18
Loading.......................................................................................18
WASHER CARE ............................................................................19
Cleaning Your Washer ...............................................................19
Water Inlet Hoses.......................................................................19
Vacation, Storage, and Moving Care.........................................20
TROUBLESHOOTING ..................................................................21
ASSISTANCE OR SERVICE.........................................................24
In the U.S.A. ...............................................................................24
In Canada ...................................................................................24
Accessories................................................................................24
WARRANTY ..................................................................................25
SÉCURITÉ DE LA LAVEUSE........................................................26
EXIGENCES D'INSTALLATION...................................................27
Outillage et pièces......................................................................27
Options .......................................................................................27
Exigences d'emplacement.........................................................28
Système de vidange...................................................................29
Spécifications électriques ..........................................................30
INSTRUCTIONS D'INSTALLATION.............................................31
Élimination des accessoires de transport..................................31
Raccordement des tuyaux d'alimentation.................................31
Raccordement du tuyau de vidange..........................................32
Immobilisation du tuyau de vidange ..........................................32
Réglage de l'aplomb de la laveuse............................................33
Achever l'installation ..................................................................33
CARACTÉRISTIQUES ET AVANTAGES .....................................34
UTILISATION DE LA LAVEUSE...................................................35
Mise en marche de la laveuse....................................................35
Utilisation du détergent approprié .............................................35
Utilisation du distributeur ...........................................................36
Pause ou remise en marche.......................................................37
Changement des programmes, options et modificateurs.........38
Témoins lumineux ......................................................................38
Programmes...............................................................................39
Sons normaux émis par la laveuse............................................41
Options .......................................................................................41
Modificateurs..............................................................................42
Guide de lessivage .....................................................................43
CONSEILS DE LESSIVAGE..........................................................44
Chargement................................................................................44
ENTRETIEN DE LA LAVEUSE .....................................................44
Nettoyage de la laveuse.............................................................44
Tuyaux d'arrivée d'eau...............................................................45
Précautions à prendre avant les vacances,
un entreposage ou un déménagement......................................46
DÉPANNAGE.................................................................................46
ASSISTANCE OU SERVICE.........................................................50
Aux États-Unis............................................................................50
Au Canada..................................................................................50
Accessoires ................................................................................50
GARANTIE.....................................................................................51
2
WASHER SAFETY
3
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
■ Pliers (that open to 1
■ Flashlight (optional)
Tools needed for connecting the drain hose
■ Locking pliers (that open to 1
Tools needed for installation
■ Open end wrenches 17 mm and 13 mm
■ Level
■ Wood block
■ Ruler or measuring tape
Parts supplied:
A B
DE
A. Drain hose form
B. Inlet hose (2)
C. Inlet hose washer (4)
D. Transport bolt hole plug (4)
Alternate Parts
Your installation may require additional parts. If you are interested in
purchasing one of the items listed here, call the toll-free number on
the cover or in the “Assistance or Service” section.
If You Have You Will Need to Buy
Laundry tub or
standpipe taller than
96" (2.4
m)
Overhead sewer Standard 20 gal. (76 L), 30" (762 mm) tall
Floor drain Siphon break, Part Number 285834;
Drain hose too short 4 ft (1.2 m) drain hose extension kit, Part
Water faucets
beyond reach of fill
hoses
9
/16" [39.5 mm])
9
/16" [39.5 mm])
C
F
G
E. Beaded strap
F. D r ain hos e
G. Hose clamp
Sump pump system (if not already
available)
drain tub or utility sink and sump pump
(available from local plumbing suppliers)
additional drain hose Part Number
8318155; and connector kit, Part Number
285835
Number 285863
2 longer water fill hoses: 6 ft (1.8 m) Part
Number
Number
76314, 10 ft (3.0 m) Part
350008
Options
Pedestal
You have the option of purchasing pedestals of different heights
separately for this washer. You may select a 10"
(394 mm) pedestal. These pedestals will add to the total height
15.5"
of the washer for a total height of approximately 48"
53.5"
(1359 mm), respectively.
AB
A. 10" (254 mm) pedestal
B. 15.5" (394 mm) pedestal
To order, call the dealer from whom you purchased your washer or
refer to the “Assistance or Service” section.
Pedestal
Color Part Number
Height
10" (254 mm) White WHP1000SQ
10" (254 mm) Black WHP1000SB
10" (254 mm) Diamond Dust (Silver) WHP1000SU
15.5" (394 mm) White XHP1550VW
15.5" (394 mm) Black XHP1550VB
15.5" (394 mm) Diamond Dust (Silver) XHP1550VU
15.5" (394 mm) New Aspen (Light Green) XHP1550VA
15.5" (394 mm) Tusc an C hestnut XHP1550VC
15.5" (394 mm) Ocean Blue XHP1550VE
15.5" (394 mm) Cranberry Red XHP1550WR
15.5" (394 mm) Lunar Silver XHP1550WL
Stack Kit
Are you planning to stack your washer and dryer? To do so you
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer
or refer to the “Assistance or Service” section. Ask for Part
Number
8541503.
(254 mm) or a
(1219 mm) or
4
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See “Drain
System.”
Companion appliance location requirements should also
be considered. Proper installation is your responsibility.
You will need
■ A water heater set to deliver 120°F (49°C) water to the
washer.
■ A grounded electrical outlet located within 6 ft (1.8 m) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■ Hot and cold water faucets located within 4 ft (1.2 m)
of the hot and cold water fill valves, and water pressure
of 20-100 psi (137.9-689.6 kPa).
■ If you live in a hard water area, use of a water softener is
recommended to control the buildup of scale in the steamer
and other areas of the washer. Over time, the buildup of lime
scale may clog the steamer, which will reduce steamer
efficiency and performance. Excessive buildup of scale may
lead to the need for steamer replacement or repair.
■ A level floor with a maximum slope of 1" (25 mm) under entire
washer. Installing the washer on soft floor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
■ A sturdy and solid floor to support the washer with a total weight
(water and load) of 400
lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in low
temperatures.
Recommended installation spacing for custom undercounter installation
The dimensions shown are for the recommended spacing.
Custom undercounter installation - Washer only
39
" min.
(990 mm)
27
1
"
(25 mm)
"
(686 mm)
1
"
(25 mm)
Recommended installation spacing for recessed or closet installation, with or without a pedestal
The dimensions shown are for the recommended spacing.
Recessed area or closet installation
3
"
(76 mm)
3
"
(76 mm)
1
"
(25 mm)
34
" min.
(864 mm)
32
"
(813 mm)
4
"
(102 mm)
Installation clearances
■ The location must be large enough to allow the washer door
to be fully opened.
■ Additional spacing should be considered for ease of installation
and servicing.
■ Additional clearances might be required for wall, door, and
floor moldings.
■ Additional spacing of 1" (25 mm) on all sides of the washer
is recommended to reduce noise transfer.
■ Companion appliance spacing should also be considered.
Washer Dimensions
27
5
1"
(1295 mm)
"
(686 mm)
32
(813 mm)
38
(965 mm)
"
"
A. Side view - closet or confined area
B. Closet door with vents
*Min. top and bottom air openings for closet door.
Recessed or closet installation - Washer on pedestal
18
" min.
(457 mm)
1
"
(25 mm)
27
"
(686 mm)
A. Recessed area
B. Side view - closet or confined area
1
"
(25 mm)
32
"
(813 mm)
4
"
(102 mm)
5
Recommended installation spacing for recessed or closet installation, with stacked washer and dryer
The dimensions shown are for the recommended spacing.
Drain System
The washer can be installed using the standpipe drain system
(oor or wall), the laundry tub drain system, or the oor drain
system. Select the drain hose installation method you need.
See “Tools and Parts.”
2
*
48 in.
2
(310 cm
24 in.
(155 cm
)
2
*
2
)
3"*
(76 mm)
3"*
(76 mm)
1"*
(25 mm)
*Required spacing
6"* (152 mm)
76"
(1930 mm)
1
5
/2"
(140 mm)
1"*
(25 mm)
27"
(686 mm)
1"*
(25 mm)
*Required spacing
**For venting out the side, 1" (25 mm) spacing is allowed.
Recommended installation spacing for cabinet installation
Standpipe drain system - wall or oor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (50 mm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute.
The top of the standpipe must be at least 30" (762 mm) high and
no higher than 96" (2.4 m) from the bottom of the washer.
30" min.
(762 mm)
A
B
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must
be at least 30" (762 mm) above the oor.
Floor drain system (view D)
The oor drain system requires a siphon break that may be
purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 28" (711 mm) from the
bottom of the washer. Additional hoses might be needed.
28" min.
30" min.
(762 mm)
(711 mm)
The dimensions shown are for the recommended spacing.
For cabinet installation with a door, the minimum ventilation
openings in the top are required.
7
" (178 mm)
4
"
(102 mm)
7
" (178 mm)
32
"
(813 mm)
1
"
(25 mm)
27
"
(686 mm)
6
9
"
(229 mm)
1
"
(25 mm)
DC
Electrical Requirements
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.
This washer is equipped with a power supply cord having a 3 prong grounding plug.
To minimize possible shock hazard, the cord must be
plugged into a mating, grounded 3 prong outlet, grounded
in accordance with local codes and ordinances. If a mating
outlet is not available, it is the personal responsibility and
obligation of the customer to have the properly grounded
outlet installed by a qualied electrician.
If codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualied electrician if you are not sure the
washer is properly grounded.
Do not have a fuse in the neutral or ground circuit.
INSTALLATION INSTRUCTIONS
Remove Transport System
IMPORTANT: Position the washer so that the rear of the washer
is within approximately 3 ft (900 mm) of its nal location.
There are 4 bolts in the rear panel of the washer that support the
suspension system during transportation. These bolts also retain
the power cord inside the washer until the bolts are removed.
1. Using a 13 mm wrench, loosen each of the bolts.
7
2. Once the bolt is loose, move it to the center of the hole and
completely pull out the bolt, including the plastic spacer
covering the bolt.
3. Once all 4 bolts are removed, discard bolt and spacers. Then pull
the power cord through the opening of the rear panel and close
the hole with the attached cap.
4. Close the bolt holes with the 4 transport bolt hole plugs. NOTE: If the washer is to be transported at a later date, call your
local service center. To avoid suspension and structural damage
to your washer, it must be properly set up for relocation by a
certified technician.
Connect the Inlet Hoses
1. Insert new flat washers (supplied) into each end of the inlet hoses.
Firmly seat the washers in the couplings.
8. Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE: Do not overtighten. Damage to the coupling can result.
9. Turn on the water faucets and check for leaks. NOTE: Replace inlet hoses after 5 years of use to reduce the
risk of hose failure. Record hose installation or replacement
dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
Connect the Drain Hose
Remove drain hose from washer drum
1. Use locking pliers, squeeze hose clamp tabs together and insert
over the end of drain hose.
A B
A. Coupling
B. Washer
2. Make sure the washer drum is empty.
3. Attach the hose with the red color indicator to the Hot (left) inlet
valve. Attaching the red coupling first makes it easier to tighten
connection with pliers. Screw on coupling by hand until it is
seated on the washer.
4. Attach the hose with the blue color indicator to the Cold (right)
water inlet valve. Screw on coupling by hand until it is seated
on the washer.
H
H. Hot water inlet
C. Cold water inlet
C
2. Slide drain hose onto washer connection.
3. Once drain hose is in place, release pliers.
5. Using pliers, check the tightness of the hose couplings already
attached to the washer.
NOTE: Do not overtighten. Damage to the coupling can result.
6. Attach hot water hose to the hot water faucet. Screw on coupling
by hand until it is seated on the washer.
7. Attach cold water hose to the cold water faucet. Screw on
coupling by hand until it is seated on the washer.
8
4. Washer drain system can be installed using a floor drain, wall
standpipe, floor standpipe, or laundry tub.
Laundry tub drain or standpipe drain
Connect the drain hose form to the corrugated drain hose.
A B
A. Snap either end of the drain hose form to the drain hose
at the point where the corrugation begins.
B. Bend drain hose over drain hose form and snap into place.
To keep drain water from going back into the washer:
■ Do not straighten the drain hose, and do not force excess drain
hose into standpipe. Hose should be secure, but loose enough
to provide a gap for air.
■ Do not lay excess hose on the bottom of the laundry tub.
Floor drain
You may need additional parts. See Floor drain under “Tools and
Parts.”
If the washer is against a wall, move the washer out slightly
before tipping back. If the washer is not level, first prop the
front with a wood block and adjust the feet as necessary;
then prop the back and adjust feet as necessary. Repeat this
step until washer is level.
2. Make sure all four feet are stable and resting on the floor. Then check that the washer is perfectly level (use a level).
3. After the washer is level, use a 17 mm open-end wrench to turn the nuts on the feet tightly against the washer cabinet.
IMPORTANT: All four feet must be tightened. If the nuts are
not tight against the washer cabinet, the washer may vibrate.
4. The washer should not move front to back, side to side, or diagonally when pushed on its top edges.
5. Slide the washer to its final location.
6. Confirm the levelness of the washer.
Complete Installation
1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See “Electrical Requirements.”
2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.
3. Check that you have all of your tools.
4. Dispose of/recycle all packaging materials.
5. Check that the water faucets are on.
6. Check for leaks around faucets and inlet hoses.
Secure the Drain Hose
1. Drape the power cord over the washer top.
2. Secure the drain hose to the laundry tub leg or standpipe with
the beaded strap provided. (See illustrations A and B.)
A BC
If the washer faucets and the drain standpipe are recessed
(see illustration C), put the hooked end of the drain hose in
the standpipe. Tightly wrap the beaded strap around the
water inlet hoses and the drain hose.
Do not force excess drain hose into the standpipe.
Level the Washer
Properly leveling your washer avoids excessive noise and vibration.
1. Check the levelness of the washer by placing a level on the
top edge of the washer, first side to side, then front to back.
7. Plug into a grounded 3 prong outlet.
8. Read “Washer Use.”
9. To test and clean your washer, make sure there are no clothes in
the washer and add one AFFRESH
Select Power, the Clean Washer cycle and then select START.
This cycle will take approximately 65
the washer to complete the entire cycle without interruption.
®
tablet to the washer drum.
minutes to complete. Allow
9
FEATURES AND BENEFITS
Electronic Controls
Flexible electronic controls are easy to use whether you are a
beginner or an expert.
Smart Dispensers
The Smart Dispensers make your washer truly automatic. This
washer provides a three-compartment dispenser which includes
separate compartments for main wash detergent, fabric softener,
and bleach. The dispenser has large pour zones. The dispenser is
self-cleaning, and can be easily removed. Laundry products are
diluted with fresh water and added to the load at the proper time
in the wash cycle.
Deep Clean with Steam
This washer has a built-in steaming unit which is combined with
the DEEP CLEAN option to provide multiple temperatures to help
remove a variety of stains from garments.
Clean Washer With AFFRESH™ Cycle with Steam
This cycle uses steam to raise the temperature of the washer and
makes the washer self-cleaning, flushing the machine’s interior
free of dirt and other residue. The use of AFFRESH® washer cleaner
or liquid chlorine bleach with this cycle will remove and help avoid
odor-causing residue.
Auto Water Level
This washer automatically adjusts water level for optimal cleaning
and rinsing performance. Two sensors determine load size, load
composition, and suds level, then the sensors adjust the water
level to the proper setting. This eliminates guesswork. The water
level is just right for every wash load size.
Heating Element
This washer has a heating element that automatically heats the
water to the optimal temperature on select cycles. This enables
stepped cleaning, a process in which warm water is brought in
and mixed with detergent first, then the water is heated. Stepped
cleaning starts the wash cycle with warm water to remove stains
(such as blood and grass).
6th SENSE® Intuitive Controls
Intuitive intelligence “knows every load” determining load sizes,
water levels, and how much cleaning time is needed.
Add A Garment
When this option is available at the beginning of the cycle, the
Add A Garment Status Light will glow for the first 4-8 minutes.
This washer allows a 4-8 minute period in which other garments
may be added to a load.
Direct Injection Wash System
This washer channels 100% of the water through the dispensers
to assure thorough rinse-out and mixture of all the laundry
products before they touch any garments. The water is then
sprayed from the top front onto the center of the load, providing
even distribution and optimum cleaning performance. It is normal
for small amounts of water to remain in the dispensers when the
wash cycle is complete.
Larger Load Size
Because there is no agitator, you can wash larger, bulkier items such
as a king-sized bedspread. You are also able to wash more clothes
at one time, which means fewer loads.
Stainless Steel Drum
The stainless steel drum eliminates corrosion and enables higher
spin speeds for more water extraction, helping to reduce drying
time compared to traditional top-load washers.
High-Efficiency Wash System
Your new front-loading, high-efficiency washer saves time with
fewer, larger loads. It also lowers your water and energy bills by
helping conserve resources.
Spin Speeds
This washer automatically selects the spin speed based on the
cycle selected. This factory setting can be changed, however.
This washer offers up to five different spin speed choices, up to
1300 rpm.
Efficient Detergent System with Anti-Escape Valve
This washer has a specially designed valve that closes during
the wash portion of the cycle so that 100% of the water and
detergent mixture is used on the load. The Efficient Detergent
System ensures that no water or detergent is wasted.
6-Point Suspension System
Shock absorbers, 2 springs, and electronic controls are specially
designed to help redistribute the load automatically and minimize
movement of the wash drum during the spin cycle. The 6-Point
Suspension System reduces the amount of force transmitted to
the floor by the washer, resulting in reduced noise and vibration.
10
WASHER USE
NOTE: The panel shown above may be different from that of your model.
Starting Your Washer
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
The following is a guide to using your washer. Please refer to
specific sections of this manual for more detailed information.
Do not store laundry products on the top surface of this washer.
Vibration is normal during operation.
Using the Proper Detergent
Use only High Efficiency detergents. The package for this type
of detergent will be marked “HE” or “High Efficiency.” This wash
system, along with less water, will create too much sudsing with
a regular non-HE detergent. Using regular detergent will likely
result in washer errors, longer cycle times, and reduced rinsing
performance. It may also result in component failures and noticeable
mold or mildew. HE detergents are made to produce the right
amount of suds for the best performance. Follow the manufacturer’s
instructions to determine the amount of detergent to use.
Remember, concentrated detergents such as 2x or higher will use
less detergent based on load size.
Use only High Efficiency (HE) detergent.
First Wash Cycle Without Laundry
Before washing clothes for the first time, if not completed during
the final installation step, choose the QUICK WASH cycle and run
it without clothes. Use only HE detergent. Use 1/2 the
manufacturer’s recommended amount for a medium-size load.
This initial cycle serves to ensure the interior is clean before
washing clothes.
For All Wash Cycles
1. Open the washer door by pulling on the handle. Sort laundry
according to color and type of fabric. Place a load of sorted
clothes in the washer. Do not overload washer. Overloading
can cause poor cleaning.
■ The washer can be fully loaded, but not tightly packed.
Washer door should close easily.
■ Mix large and small items and avoid washing single items.
Load evenly.
■ Wash small items, such as infant socks, in mesh garment
bags. It is recommended that more than one garment bag
be used, and that each garment bag be filled with equal
amounts of material.
■ When unloading garments, occasionally check under the
gray colored seal at the front of the tub for small items.
2. Close the washer door by pushing it firmly until the lock clicks. The washer door will remain locked during the wash cycle.
NOTES:
■ After any wash cycle is completed, the door must be
opened and then closed before a new cycle can begin.
■ The door can be opened only if PAUSE/CANCEL is
selected while the Add A Garment light is glowing or if
the cycle has been canceled.
■ See “To cancel a cycle” in “Changing Cycles, Options,
and Modifiers” section.
3. Open the dispenser drawer and add laundry products to the detergent, bleach, or fabric softener compartments. Close drawer slowly to avoid spills. See “Using the Dispenser.”
4.
Turn on the washer by selecting POWER. Select one of the cycles
by turning the cycle selector. The indicator light for the selected
cycle will glow green. When you are selecting a wash cycle, the
preset options and modifiers (such as Water Temp, Spin Speed,
Soil Level, and Rinse) for the selected cycle will glow green.
Selectable options will glow amber. If an option or modifier is
unavailable with a selected cycle, the light will not illuminate.
The display shows the estimated time remaining. The preset
settings provide the recommended fabric care for the selected
cycle. See “Cycles.”
11
5. Select the desired Options. Not all options are available with
all cycles. See “Options.”
6. Select the desired modifiers such as Water Temp, Spin Speed,
Soil Level, and Rinse. Not all modifiers are available with all cycles
and options. See “Modifiers.”
7. If desired, select the CYCLE SIGNAL. The signal is helpful
when you are washing items that should be removed from the
washer as soon as it stops. Select Loud, Soft, or Off.
8. If desired, select the BUTTON SOUND. This feature makes a
sound each time a button is pressed. Select Loud, Soft, or Off.
9. Select and hold START for approximately 1 second.
■ If you do not select START within 5 minutes of choosing
a cycle, the washer automatically shuts off.
■ When the wash cycle is complete, the DONE status light
glows, the door unlocks, and the wash load can be
removed from the washer. The washer powers down
automatically 60 minutes after the cycle is complete
and the DONE light goes off. To power down the washer
manually after the wash cycle is complete, select PAUSE/
CANCEL once.
10. To use the same cycle again, press POWER first, then select
START.
11. To begin the wash cycle later
Select DELAY WASH until the desired delay time (in hours)
shows in the Estimated Time Remaining display. Select START.
The countdown to the wash cycle will show in the display
window.
IMPORTANT: When delaying a cycle, use only powdered
detergents in the main wash compartment since liquid
detergents may seep out of the compartment during Delay
Wash, before the wash cycle begins.
To fill dispenser compartments
1. Pull out the dispenser drawer.
2. Add the desired laundry product to the proper compartment.
3. Push in the dispenser drawer slowly and completely (to avoid
a spill).
A
B
Dispenser
A. Detergent type selector
B. Main Wash detergent compartment
C. Dispenser release lever
D. Chlorine bleach compartment
E. Fabric softener compartment
C
D
E
Using the Dispenser
Your new washer has a dispenser drawer with three separate
compartments for your laundry products—one is for detergent,
one is for liquid chlorine bleach, and one is for liquid fabric
softener. Laundry products are diluted and dispensed
automatically at the proper time during the wash cycle,
making it unnecessary for you to return to the washer during
the cycle to add them.
It is normal for small amounts of water to remain in the
dispensers when the wash cycle is complete.
Do not put laundry products directly into the wash tub. Always
use the proper dispensers when adding laundry products.
Choosing the Right Detergent
Use only High Efficiency detergents. The package for this type of
detergent will be marked “HE” or “High Efficiency.” This wash
system, along with less water, will create too much sudsing with a
regular non-HE detergent. Using regular detergent will likely result
in washer errors, longer cycle times, and reduced rinsing
performance. It may also result in component failures and
noticeable mold or mildew. HE detergents are made to produce
the right amount of suds for the best performance. Follow the
manufacturer's instructions to determine the amount of detergent
to use. Remember, concentrated detergents such as 2x or higher
will use less detergent based on load size.
Main Wash detergent compartment
(Letter B in Dispenser Illustration)
Add liquid or powdered HE detergent to this compartment for
your main wash cycle. The detergent type selector (A) must
always be in the correct position for the detergent type used. Slide
the detergent type selector to the correct position.
IMPORTANT: If you are using the Delay Wash option, powdered
detergent must be used in the Main Wash compartment, since
liquid detergents may seep out of the Main Wash compartment
before the main wash begins.
■ Use the detergent manufacturer's recommended amount for
load size.
■ Liquid or powdered color-safe bleach may be added to the Main
Wash compartment along with the same type of detergent,
liquid or powdered.
■ Liquid detergent:
A
12
Use only HE High Efficiency detergent.
Selector in position for liquid detergent
A. Detergent type selector
■ Powdered detergent:
5. Press START (for approximately 1 second) to restart the washer at the beginning of the new cycle.
To cancel a cycle
A
Selector in position for powdered detergent
A. Detergent type selector
Chlorine bleach compartment
(Letter D in Dispenser Illustration)
Add no more than 2/3 cup (160 mL) liquid chlorine bleach to this
compartment. The bleach will be automatically diluted and
dispensed at the optimum time during the first rinse after the wash
cycle. This compartment cannot dilute powdered bleach.
■ Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess.
■ Do not fill beyond the “MAX” level.
NOTE: Overfilling could cause garment damage.
■ At the end of the cycle, a small amount of water may be left in
the dispenser. This is normal.
Fabric softener compartment
(Letter E in Dispenser Illustration)
Pour measured liquid fabric softener into the fabric softener
dispenser, if desired.
IMPORTANT: Dilute all fabric softener with water for a total of
1/4 cup (60 mL).
■ Do not overfill. The dispenser holds 1/4 cup (60 mL).
■ Do not spill or drip any fabric softener onto the clothes.
NOTES:
■
Use only liquid fabric softener in this dispenser.
Do not use fabric softener dispensing balls in this washer.
Dispensing balls will not operate correctly with this washer.
Pausing or Restarting
1. To pause the washer at any time, press PAUSE/CANCEL.
2. To continue the cycle, press START (for approximately 1 second).
Changing Cycles, Options, and Modifiers
Not all Options and Modifiers are available with all cycles.
Available modifiers will glow amber. If an option or modifier is
unavailable with a selected cycle, the light will not illuminate.
Cycles, Options, and Modifiers can be changed anytime before
START is selected.
To cancel a cycle and select a new cycle
1. Press PAUSE/CANCEL twice.
2. Press POWER.
3. Select desired cycle.
4. Select the desired Options or modifiers such as Water Temp,
Spin Speed, and Soil Level.
1. Press PAUSE/CANCEL twice.
2. The washer powers down, the door unlocks, and clothes can
be removed.
NOTE: If the water level or the temperature is too high, the washer
will drain automatically before the door unlocks.
To change Options or Modifiers after the cycle has started
1. Press PAUSE/CANCEL once.
2. Select the desired Options or Modifiers such as Water Temp,
Spin Speed, and Soil Level. Available selections will glow amber.
3. Press START (for approximately 1 second) to continue the cycle.
To drain the washer manually
1. Press PAUSE/CANCEL twice.
2. Press POWER.
3. Select DRAIN/SPIN.
4. Press START (for approximately 1 second) to begin the drain.
5. When the spin is complete, the door unlocks. Items can be
removed from the washer.
Status Lights
These lights show which portion of the cycle the washer is
operating. They also indicate when you can add an additional
item to the wash cycle and when the controls are locked.
Add A Garment
This washer allows a 4-8 minute period in which other garments
may be added to the load. You can add items to the washer if the
Add A Garment status light is glowing.
To add items when Add A Garment light is glowing
1. Select PAUSE/CANCEL once. The washer door unlocks after
a few seconds, and items can be added.
2. To continue the cycle, close the door and select and hold START (for approximately 1 second).
To add items when the Add A Garment light is not glowing
1. You must cancel the current cycle by pressing PAUSE/CANCEL
twice. This will cancel the wash cycle and options. The washer
door unlocks, and items can be added.
2. Close the door, press POWER, and select the new cycle and
options. Select and hold START (for approximately 1
Done
The Done status light stays on for 60 minutes after the cycle is
complete, and then the washer shuts off.
second).
13
Sanitized
This washer has a Sanitize water temperature that is certied
by NSF International, an independent third-party testing and
certication organization. The certication veries that the
sanitizing cycle reduces 99.9% of bacteria typically found
on clothing, bedding, and towels, and there is no carryover
of bacteria between loads after the cycle is complete.
Certied to Sanitize
If the “Sanitize” wash temperature was selected, when the wash
cycle is complete, the DONE status light will illuminate, the door
unlocks, and the wash load can be removed from the washer.
The washer powers down automatically 60 minutes after the
cycle is complete and the DONE status light turns off. Only cycles
with sanitize wash temperature selected have been designed to
meet the requirements of NSF Protocol P172
Performance of Residential and Commercial, Family-sized
clothes washer.
Sanitization
Controls Lock/Unlock
The Controls Lock avoids unintended use of the washer. You can
also use the control lock feature to avoid unintended cycle or
option changes during a cycle. When Controls Lock is lit, all
buttons are disabled except for Pause/Cancel and Start. You can
lock the controls while the washer is operating.
To lock the controls
Press and hold CONTROLS LOCK/UNLOCK for 3 seconds after the
cycle starts, or when the washer is turned off.
The status light next to the CONTROLS LOCK/UNLOCK button
will glow.
To unlock the controls
Press and hold CONTROLS LOCK/UNLOCK for 3 seconds until
the status
NOTE: To lock or unlock the controls when the washer is off,
press and hold CONTROLS LOCK/UNLOCK for 3 seconds.
light turns off.
Cycles
Cycles can be selected by turning the Cycle Control knob to the
desired cycle. Each cycle is designed for different types of fabric
and soil levels. The modier indicator lights, on the right-hand
side of the panel, will change as cycles are selected.
Each cycle has a preset Soil Level (estimated cycle time), Water Temperature, and Spin Speed, and may have preset options. The preset settings provide the recommended fabric care for the selected cycle.
The preset settings will glow green to show the preselected
options and modiers, and
START is pressed. Not all options and modiers are available
with all cycles. Available selections glow amber. (To change
settings after the cycle has started, press PAUSE/CANCEL
once, then select the desired settings. Press START to continue
the cycle.)
Powdered detergents may not dissolve well in a slow-speed cycle. For best results, use liquid detergent in slow-speed cycles.
Preset cycle settings
Each cycle has a preset Soil Level (cycle time), Water Temperature,
and Spin Speed. The preset settings provide the recommended
fabric care for the selected cycle. See chart.
Cycle
Soil Level
(cycle time)
Whitest
Whites
Heavy Duty Normal
Bulky Items Normal
Normal
(1:20)
(1:10)
(0:55)
can be changed anytime before
Water Temp Spin Speed
Hot/Cold High
Hot/Cold High
Warm/Cold Low
Door Locked
When the status light glows, the door is locked.
Sensing/Revising Estimated Time
The cycle times vary automatically based on your water pressure,
water temperature, detergent, and clothes load.
The washer will automatically sense the progress in the cycle and
adjust the Estimated Time Remaining display. While the washer is
sensing, the estimated time will ash and the Sensing status light
will glow. When the sensing is complete, the ashing stops, the
status light goes off, and the Estimated Time Remaining display
is updated.
The cycle time will be extended if oversudsing occurs or the load
is unbalanced. The SUD routine removes extra suds and assures
proper rinsing of your garments. See “Troubleshooting.” During
the unbalance routine, the time displayed may pause until this
activity is complete, then resume with the remainder of the cycle.
14
Active Wear Normal
Normal/
Casual
Delicate Normal
Hand
Washables
Quick Wash
(2-3 items)
Clean
Washer With
AFFRESH™
Soak Normal
(0:40)
Normal
(0:50)
(0:40)
Normal
(0:30)
Light
(0:18)
N/A
(1:05)
(0:32)
Warm/Cold Medium
Warm/Cold High
Warm/Cold Medium
Cold/Cold Low
Warm/Cold High
N/A N/A
Warm/Cold No Spin
Cycle
Soil Level
Water Temp Spin Speed
(cycle time)
Rinse/Spin N/A
Drain/Spin N/A
To change the preset cycle settings
Press the selector of each available setting until the desired
setting glows green.
(0:22)
(0:13)
Warm/Cold High
N/A High
Whitest Whites
This cycle is especially designed for cleaning loads of soiled white
fabrics with the addition of bleach. Hot washing temperatures
assure optimal bleach activity. An additional rinse provides optimal
rinse performance to avoid chlorine residues on your laundry.
This cycle combines fast-speed tumbling, longer wash time,
and high speed spin to shorten drying time.
Quick Wash
Use this cycle to wash small loads of 2-3 lightly soiled garments
that are needed in a hurry. This cycle combines fast-speed tumbling,
a shortened wash time, and high speed spin to shorten
drying time.
Clean Washer With AFFRESH™ cycle
Use the Clean Washer With AFFRESH™ cycle once a month to
keep the inside of your washer fresh and clean. This cycle uses a
higher water level. Use with AFFRESH
liquid chlorine bleach to thoroughly clean the inside of your washing
machine. This cycle should not be interrupted. See “Cleaning Your
Washer” in the “Washer Care” section.
IMPORTANT: Do not place garments or other items in the washer
during the Clean Washer With AFFRESH™ cycle. Use this cycle with
an empty wash drum.
®
washer cleaner tablet or
Soak
Heavy Duty
Use this cycle to wash loads of sturdy, colorfast fabrics and heavily
soiled garments. This cycle combines fast-speed tumbling, longer
wash time, and high speed spin to shorten drying times. If the water
temperature is lower than needed for this cycle, the heater will warm
the water to the optimum temperature.
Bulky Items
Use this cycle to wash large items such as blankets and comforters.
This cycle starts with a soak to thoroughly saturate your large load.
This is followed by medium wash action and low-spin speeds to
maintain load balance.
Active Wear
Use this cycle to wash small loads of exercise wear such as biking
shorts, tank tops, running tights, and other performance clothing.
This cycle combines low-speed tumbling and medium-speed spin
for gentle fabric care.
Normal/Casual
Use this cycle to wash loads of no-iron fabrics, such as sport shirts,
blouses, casual business clothes, permanent press blends,
cottons and linens, and synthetic fabrics. This cycle combines
medium-speed tumbling, high-speed spin, and a load cooling
process to reduce wrinkling.
NOTE: For the best energy performance, use the Normal/Casual
Cycle.
Use the Soak cycle to help remove small spots of set-in stains on
fabrics. This cycle provides a soak time with warm or cold water
followed by drain. Extra water, a short tumbling phase for equal
distribution of the laundry, and a soaking time without drum
movement improve the removal of set-in stains. Drain without spin
assures gentle treatment, even for delicate articles.
Rinse/Spin
Use this cycle to get a rinse and spin only. This cycle combines fastspeed tumbling and high speed spin. If desired, you can reduce the
spin speed by selecting the speed you want from the SPIN SPEED
modier.
A Rinse/Spin cycle is useful for:
Loads that need rinsing only, like swimsuits. NOTE: For more delicate loads, when using a Rinse & Spin
cycle to rinse swimwear, change the Speed Spin Modier
setting to Medium or Low to avoid fabric stress.
Adding fabric softener to a load.
Drain/Spin
Use this cycle to drain your washer or to drain and spin your wash
load. The spin speed is preset to high. If desired, you can reduce the
spin speed by selecting the speed you want from the SPIN SPEED
modier.
NOTE: Loads of synthetics, delicate fabrics, hand washables, and
washable woolens should be drained with no spin or low spin speed
to avoid fabric stress.
Delicate
Use this cycle to wash sheer fabrics and lingerie. This cycle
combines low-speed tumbling and medium-speed spin for gentle
fabric care.
Hand Washables
Use this cycle to clean hand washable and special-care garments.
Similar to the way garments are hand washed in a sink, the wash
action of this cycle combines periods of low-speed tumbling and
soaking. Low-speed spin reduces wrinkling.
Use mesh garment bags as necessary.
Normal Washer Sounds
As with any new product, you will hear sounds that you are not
accustomed to. You may hear various sounds when the door is
locked and unlocked, and during the washing, rinsing, and spinning
process. Between changes in wash actions, there will be
momentary pauses. You will hear water spraying and splashing
during the wash and rinse cycles. These new sounds and pauses
are part of normal washer operation.
15
Options
You can customize your wash by adding options to your cycle
selections. You can add or change an option after starting a cycle
anytime before the selected option begins. Not all options are
available with all cycles. Available options will glow amber. Current
selections will glow green. If an option is unavailable with a selected
cycle, the light will not illuminate.
■ See the “Laundry Guide” for an overview of possible options for
each Wash Cycle selection.
■ You can select more than one option for a cycle. Some options
cannot be added to some cycles. For example, Deep Clean
cannot be added to the Quick Wash cycle.
■ If an option is unavailable with a selected cycle, there will be
3
short tones, and the light for that option will not glow when
selected.
NightQuiet™ option
In this option, the washer will sense vibration in the wash cycle and
may adjust the spin speed to lower sound levels generated during
the spin.
Cycle Signal
This signal is helpful when you are removing items from the
washer as soon as it stops. Press CYCLE SIGNAL to select Loud,
Soft, or Off. To activate/deactivate button sound hold cycle signal
button for 3 seconds.
Modifiers
Preset cycle settings of Water Temperature, Spin Speed, Soil
Level, and Rinse can be changed. You can change a modifier after
starting a cycle anytime before the selected modifier begins. Not all
modifiers are available with all cycles and options. Available options
will glow amber. Current selections will glow green. If a modifier is
unavailable with a selected cycle, the light will not illuminate.
NOTE: The panel shown below may be different from that of your
model.
Delay Wash
To begin the wash cycle later, select DELAY WASH until the desired
delay time (in hours) shows in the Estimated Time Remaining
display, and then select START. The countdown to the wash cycle
will show in the display window, and the button indicator will blink
until the cycle begins.
IMPORTANT: When delaying a cycle, use only powdered
detergents in the high efficiency “HE” detergent compartment
since liquid detergents may seep out of the compartment during
Delay Wash, before the wash cycle begins.
TumbleFresh™ option
Use this option when you are not able to unload your clothes,
soon after the wash cycle ends. This option provides periodic
tumbling for up to 6 hours to help freshen your clothes. During
this time, the “Done” indicator remains activated, the door
remains locked, and the TumbleFresh™ indicator light will flash.
The TumbleFresh™ option will automatically stop and the door
lock will be released after this time expires, or if you press cancel
at anytime to unload your laundry.
Deep Clean with Steam
Use this option for heavily soiled loads that need improved stain
treatment, loads with multiple types of stains, or loads you
suspect as having stains, but are afraid may have been missed
(no sorting or searching for stains). When Deep Clean with Steam
is selected, the water temperature of the selected wash cycle is
automatically set to warm. The water will then be slowly heated to
the temperature selected, along with steam, to aid in stain removal.
This option will provide optimal removal of organic stains such as
blood and grass.
■ To change the water temperature, select the WATER TEMP
button until the desired setting glows green.
■ To change the spin speed, select the SPIN SPEED button
until the desired setting glows green.
■ To change cycle time, select SOIL LEVEL button until the
desired setting glows green.
■ To change the rinse, select RINSE button until the desired
setting glows green.
Water Temp
Select a water temperature based on the type of load you are
washing. Use the warmest wash water safe for fabrics. Follow
garment label instructions.
In wash water temperatures colder than 60°F (15.6°C), detergents
do not dissolve well. Soils may be difficult to remove.
■ This washer has a Sanitize water temperature that is certified
by NSF International, an independent third-party testing and
certification organization. The certification verifies that the
sanitizing cycle reduces 99.9% of bacteria typically found
on clothing, bedding, and towels, and there is no carryover
of bacteria between loads after the cycle is complete.
16
Certified to Sanitize
Loading...