Whirlpool MHW7100DW, WFW8740DW, WFW72HEDW, MHW4200BW, WFW97HEDC Installation Instructions
...
WASHER INSTALLATION
INSTRUCTIONS
INSTRUCTIONS
Table of Contents
WASHER SAFETY .........................................................1
INSTALLATION REQUIREMENTS ................................2
Tools and Parts ................................................................ 2
Location Requirements ..................................................3
Drain System ...................................................................4
Electrical Requirements .................................................5
INSTALLATION INSTRUCTIONS ..................................5
Connect Drain Hose ........................................................ 6
Connect Inlet Hoses ........................................................7
Level Washer ...................................................................8
Complete Installation Checklist ..................................... 9
Para obtener acceso al instrucciones de instalación en español, o para obtener información adicional acerca
de su producto, visite: www.whirlpool.com
INSTALLATION NOTES
Date of purchase: _________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
D’INSTALLATION
DE LA LAVEUSE
Table des matières
SÉCURITÉ DE LA LAVEUSE ......................................10
EXIGENCES D’INSTALLATION ..................................11
Outillage et pièces ........................................................10
Exigences d’emplacement ...........................................12
Système de vidange ...................................................... 14
Spécications électriques ............................................ 14
INSTRUCTIONS D’INSTALLATION ............................15
Raccordement du tuyau de vidange............................16
Raccordement des tuyaux d’arrivée d’eau .................17
Établissement de l’aplomb de la laveuse .................... 19
Liste de vérication pour l’achèvement
de l’installation ..............................................................20
NOTES SUR L’INSTALLATION
Date d’achat : ____________________________________
Date d’installation : _______________________________
Installateur : _____________________________________
Numéro de modèle : _______________________________
Numéro de série : _________________________________
WASHER SAFETY
W10631155A
W10631156A-SP
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather required tools and parts before starting installation.
Tools needed:
Drain hose with clamp
and form (may be shipped
unassembled)
Available Accessories:
Adjustable or open end
wrenches 1/2" (13 mm)
and 9/16" (14 mm)
Level
An optional matching pedestal is available for your washer.
Please contact your retailer for ordering information, or see
the “Assistance or Service” page on the back of your “Use and
Care Guide”.
4" min
(102 mm)
Wood block
Pliers that open to
19⁄16" (39.5 mm)
Ruler or measuring tape
Optional tools:
Flashlight Bucket
Parts needed: (Not supplied with washer)
Water inlet hoses (2)
Flat inlet hose washers (4)
Parts supplied:
NOTE: All parts supplied for installation are in the washer
basket.
Alternate parts: (Not supplied with washer)
Your installation may require additional parts. To order, please
refer to toll-free numbers on the back page of your “Use and
Care Guide”.
If you have: You will need:
Overhead sewer Standard 20 gal. (76 L) 39" (990 mm)
tall drain tub or utility sink, sump
pump and connectors (available from
local plumbing suppliers)
1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm)
diameter Standpipe Adapter
Part Number 3363920
Connector Kit Part Number 285835
Drain hose too short Extension Drain Hose Part
Number 285863
Connector Kit Part Number 285835
Lint clogged drain Drain Protector Part Number 367031
Connector Kit Part Number 285835
Floor drain system Siphon Break Kit Part Number 285834
Connector Kit (x2) Part Number 285835
Extension Drain Hose Part
Number 285863
Alternate Inlet Hoses: (may be required for some
installations, not supplied with washer)
n
8212656RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack)
n
8212641RP 5 ft. (1.5 m) Inlet hose, Black EPDM (2 pack)
n
8212546RP 4 ft. (1.2 m) Inlet hose, Black EPDM (2 pack)
n
8212545RP 5 ft. (1.5 m) Inlet hose, Red and Blue EPDM
(2 pack)
n
8212487RP 5 ft. (1.5 m) Nylon braided inlet hose (2 pack)
n
8212638RP 6 ft. (1.8 m) Nylon braided inlet hose, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
n
8212637RP 6 ft. (1.8 m) Inlet hose, Black EPDM, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
Cable tie
2
Transport bolt hole
plugs (4)
LOCATION REQUIREMENTS
Proper installation is your responsibility.
You will need:
n
A water heater set to 120° F (49° C).
n
A grounded electrical outlet located within 6 ft (1.8 m) of
power cord on back of washer.
n
Hot and cold water faucets located within 4 ft (1.2 m) of hot
and cold water ll valves on washer, and water pressure of
20-100 psi (137.9-689.6 kPa).
n
A level oor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet or surfaces with foam backing is
not recommended.
n
Floor must support washer’s total weight (with water and load)
of 315 lbs (143 kgs).
IMPORTANT: Do not install, store or operate washer where it will
be exposed to weather or in temperatures below 32° F (0° C).
Water remaining in washer after use may cause damage in low
temperatures. See “Washer Care” in your “Use and Care Guide”
for winterizing information.
Whirlpool Models*
3
52
/4"
(1340 mm)
335/16"
(846 mm)
27"
(686 mm)
Maytag Models
15
/16"
52
(1345 mm)
3215/16"
(837 mm)
383/4" - 393/4"
(948 mm - 1010 mm)
27"
(686 mm)
All dimensions show recommended spacing allowed, except for
closet door ventilation openings which are the minimum required.
For each arrangement, consider allowing more space for ease of
installation and servicing, and spacing for companion appliances
and clearances for walls, doors, and oor moldings.
Space must be large enough to allow door to fully open.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed, top
and bottom air openings in door are required.
Recessed area or closet installation
(stacked washer and dryer):
523/4"
(1340 mm)
331/8"
(841 mm)
383/4" - 393/4"
(948 mm - 1010 mm)
27"
(686 mm)
3"
2
48 in.
(310 cm2)
2
24 in.
(155 cm2)
(76 mm)
3"
(76 mm)
1"
*
(25 mm)
(152 mm)
(152 mm)
761/2"
(1943 mm)
5"
(127 mm)
* Add spacing of 1" (25 mm) on all sides of washer/dryer.
Custom under counter installation:
6"
6"
383/4" - 393/4"
(948 mm - 1010 mm)
* For additional details (or information) specic to your model,
refer to the Dimension Guide at www.whirlpool.com.
3
2
48 in.
(310 cm2)
2
24 in.
(155 cm2)
3"
(76 mm)
Custom cabinet installation:Recessed area or closet installation (washer only):
7"
(178 mm)
14"
(356 mm)
3"
(76 mm)
1"
*
(25 mm)
4"
**
(102 mm)
1"
*
(25 mm)
4"
**
(102 mm)
* Add spacing of 1" (25 mm) on all sides of washer. ** Recommended 4" (102 mm), minimum 1.5" (38 mm)
DRAIN SYSTEM
Drain system can be installed using a oor drain, wall standpipe,
oor standpipe, or laundry tub. Select method you need.
IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of drain
hose should be inside standpipe. Always secure drain hose with
cable tie.
Floor standpipe drain system
4.5"
(114 mm)
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm)
diameter to 1" (25 mm) diameter Standpipe Adapter Kit is
available (Part Number 3363920). Top of standpipe must be at
least 30" (762 mm) high; install no higher than 96" (2.44 m) from
bottom of washer. If you have an overhead sewer and need to
pump higher than 96" (2.44 m), a sump pump and associated
hardware are needed. See “Alternate Parts”.
Laundry tub drain system
4.5"
(114 mm)
min.
30"
(762 mm)
Minimum capacity: 20 gal. (76 L). Top of laundry tub must
be at least 30" (762 mm) above oor; install no higher than
96" (2.44 m) from bottom of washer.
Floor drain system
Wall standpipe drain system
4.5"
(114 mm)
See requirements for oor standpipe drain system.
4
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. See “Alternate Parts”. Minimum siphon
break height: 28" (710 mm) from bottom of washer. (Additional
hoses may be needed.)
ELECTRICAL REQUIREMENTS
INSTALLATION INSTRUCTIONS
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
n
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is recommended that a separate circuit
breaker serving only this appliance be provided.
n
This washer is equipped with a power supply cord having
a 3 prong grounding plug.
n
To minimize possible shock hazard, the cord must be plugged
into a mating, 3 prong, grounding-type outlet, grounded in
accordance with local codes and ordinances. If a mating outlet
is not available, it is the personal responsibility and obligation
of the customer to have the properly grounded outlet installed
by a qualied electrician.
n
If codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine that
the ground path is adequate.
n
Do not ground to a gas pipe.
n
Check with a qualied electrician if you are not sure the
washer is properly grounded.
n
Do not have a fuse in the neutral or ground circuit.
NOTE: To avoid oor damage, set washer onto cardboard
before moving it.
1. Move washer
48"
(1.2 m)
It is necessary to remove all shipping materials for proper
operation and to avoid excessive noise from washer.
Move washer to within 4 ft (1.2 m) of its nal location. It must
be in a fully upright position.
2. Locate transport bolts
Locate four transport bolts on rear of washer.
5
3. Remove transport bolts from
washer
6. Place power cord over top
Loosen bolts with a 1/2" (13 mm) wrench. Slide each bolt and
spacer to center of hole. Pull bolts and plastic spacers from
back of washer. Discard bolts and spacers.
4. Cover bolt holes with transport
bolt hole plugs
Close bolt holes on cabinet back with four transport bolt hole
plugs included with washer parts.
5. Remove power cord
Remove the yellow shipping strap from the cord. Gently
place power cord over top of washer to allow free access
to back of washer.
IMPORTANT: Do not plug washer in until installation has
been completed.
CONNECT DRAIN HOSE
7. Attach drain hose to drain port
Ribs
If clamp is not already in place on elbow end of drain hose,
squeeze clamp with pliers and slide it over end of hose,
centering it between the ribs, as shown. Squeeze clamp with
pliers and slide elbow end of drain hose onto drain port and
secure with clamp.
For a laundry tub or standpipe drain, go to step 9.
For a oor drain, remove the preinstalled drain hose form
as shown in Step 8. You may need additional parts with
separate directions. See “Alternate Parts”.
Pull power cord through opening in rear panel and close hole
with attached cap.
NOTE: If washer is transported at later date, call your local
service center to avoid suspension and structural damage,
a certied technician must properly set up washer for
relocation.
6
Loading...