ASSISTANCE OU SERVICE ...................... Couverture arrière
2
Washer Safety
3
Accessories designed for your appliance:
Accessories
INSTALLATION & MAINTENANCE
ACCESSORIES
FACTORY CERTIFIED PARTS – these three
words represent quality parts and accessories
designed specically for your appliance.
Time tested engineering that meets
our strict quality specications.
FACTORY CERTIFIED PARTS
Customize your new washer and dryer with the following
genuine Whirlpool accessories. For more information on
options and ordering, call 1-866-698-2538 or visit us at:
www.whirlpool.com/accessories. In Canada, call
1-800-688-2002 or visit us at www.whirlpool.ca.
15" Pedestal
Color-matched pedestals raise
the washer and dryer to a more
comfortable working height.
The large drawer provides
convenient storage.
Load & Go™ Liquid HE
Detergent Cartridge
(on some models)
If you frequently alternate
between two different liquid
HE detergents, you may
also purchase an additional
cartridge.
Stack Kit
If space is at a premium, the
stack kit allows the dryer to
be installed on top of the
washer.
Single-Dose Liquid HE
Detergent Cup
(on some models)
The cup provides a way
to dispense a single dose
of liquid detergent.
4
Control Panel and Features
Not all features and cycles are available on all models.
NOTES:
n
The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are registered,
touch the control panel with your fingertip, not your fingernail. When selecting a setting or option, simply touch its name.
n
At cycle completion, your setting and option choices will be remembered for your next use of that cycle. However, if power is lost
to the washer, the settings and options will go back to the factory defaults.
4
1
7
1
2
2
3
6
BEACD
5
4
3
A
7
1
2
3
6
CE
BD
5
4
ED
5
5
1
POWER BUTTON
Touch to turn the washer on and off. Touch to stop/cancel
a cycle at any time.
NOTE: Turning the Wash Cycle knob will also turn the
washer on.
2
WASH CYCLE KNOB
Turn the knob to select a cycle for your laundry load. An LED
will light up for the cycle selected.
NOTE: The Clean Washer with affresh® LED will flash when
the washer has run 30 wash cycles as a reminder to run the
Clean Washer with affresh® cycle.
See “Cycle Guide” for detailed descriptions of cycles.
NOTE: For best results when using the Wash & Dry cycle,
use for loads weighing 2 lbs and less, such as a soccer
uniform or a running tank and shorts. Allow the cycle to
run the full duration of 12 hours.
3
START BUTTON
Touch and hold for 3 seconds until the light above the
Start button comes on to start a cycle, or touch once while a
cycle is in process to pause it. If you want to add a garment,
you can touch the Start button when the “Add Garment”
LED is on.
4
LED DISPLAY AND SETTINGS
When you select a cycle, its default settings will light up and
the Estimated Time Remaining will be displayed. Factors
such as load size, wash temperature, and water pressure
may affect the time shown in the display. Tightly packing,
unbalanced loads, or excessive suds may cause the washer
to lengthen the cycle time, as well.
Touch the desired setting along the bottom of the display
to adjust. See “Cycle Guide” for available settings on each
cycle. Not all settings are available with all cycles.
Cycle Status Lights
For details, see “Cycle Status Lights” section.
Load & Go™ – Detergent Concentration
and Water Hardness (on some models)
Touch DETERGENT CONCENTRATION to set detergent
concentration from 2x to 6x. Touch WATER HARDNESS
to set water hardness (normal, hard, or soft). For details,
see “About Detergent Concentration” section.
IMPORTANT: When using the dispenser cartridge with
concentrated liquid detergent, be sure to change the
detergent concentration settings in the control if the
detergent used is different than factory preset of 2x
concentration.
Wash Temp
The recommended wash temperature is preset for each
cycle. You may also select a wash temperature based
on the type of fabric and soils being washed. For best
results, use the warmest wash water safe for your
fabric, following the garment label instructions.
All wash temperatures feature a cold rinse.
Spin
This washer automatically selects the spin speed
based on the cycle selected. Some preset speeds
can be changed.
n
Faster spin speeds mean shorter dry times, but may
increase wrinkling in your load.
n
Slower spin speeds reduce wrinkling, but will leave
your load more damp.
Soil
Soil level (wash time) is preset for each wash cycle.
When you change the soil setting,
increase or decrease in the Estimated Time Remaining
display.
For most loads, use the soil level that is preset with
the cycle you have chosen. For heavily soiled and
sturdy fabrics,
time. For lightly soiled and delicate fabrics,
Soil setting
settings will help reduce tangling and wrinkling.
Presoak
Touch to add a Presoak time of your choice to a
wash cycle. Items will gently tumble through the
detergent and water for the selected time to help
loosen tough stains.
OPTIONS
5
Touch to activate additional wash options or additional
features on the washer before touching the Start button.
Additional wash options or additional features selected
after touching the Start button may not activate.
Once a wash option or additional feature is selected, it is
saved for the cycle selected. To return to factory default
cycle settings, unplug washer for 30 seconds; then
plug back in.
Adjust Delay Time
A
Touch – or + to delay the start of the wash cycle by up
to 8 to 12 hours depending on your model.
FanFresh® Option (on some models)
B
The FanFresh® option will periodically tumble the load
after the end of the cycle for up to 12 hours, while the
integrated fan circulates air through the washer to
reduce humidity. To turn on the FanFresh® option, touch
FANFRESH. If, however, the FanFresh® option is turned
on, it will stay on for all future cycles until turned back
off – the washer remembers the last on/off status set.
To turn off the FanFresh® option, touch FANFRESH.
You may also activate the FanFresh® option without
running a cycle by touching and holding the Power
button for one second, then touching and holding
FANFRESH for 3 seconds, then touching and holding
the Start button for 3 seconds.
To turn off the FanFresh® option when it is running,
touch the Power button.
NOTE: The door will lock while the FanFresh® option
is active. To cancel the option and unlock the door,
touch the Power button.
Extra Rinse
C
Activate this option to add an extra rinse to most cycles.
NOTE: Extra Rinse can also be used to turn on the
Drum Light (on some models). Simply touch and hold
EXTRA RINSE for 3 seconds.
use the Soil setting
to select less wash time. Lower soil level
the cycle time will
to select more wash
use the
6
Cycle Signal
D
Use this option to set the volume level or turn off the
signal that sounds at end of cycle.
With each touch of the Cycle Signal a number is
displayed for the sound level selected: 0 = off, 1 = low,
2 = medium, 3 = high.
NOTE: Touch-tone volume does not change.
To turn off the tones that sound when a setting is
touched: Touch and hold CYCLE SIGNAL for about
3 seconds. Repeat to turn them on.
Control Lock
E
Touch and hold for 3 seconds to lock the controls
to avoid unwanted changes or operation. Touch
and hold for 3 seconds again to unlock. For each second
CONTROL LOCK is held down, the display will count
down one second: you will see “3,” then “2,” then “1.”
You may still touch the Start button to pause the cycle,
or touch the Power button to turn off the washer.
DISPENSERS
8
ADDITIONAL OPTION
Drum Light (on some models)
Touch and hold EXTRA RINSE for 3 seconds to turn on
the Drum Light.
ECOBOOST™ OPTION
6
Touch to activate the EcoBoost™ option. The EcoBoost™
option provides additional energy savings through reduced
hot water usage and maintains cleaning performance by
lengthening the wash time on some cycles.
NOTE: Energy savings may vary across loads and cycles.
STEAM CLEAN OPTION
7
The Steam Clean option adds additional soak and wash
time to many cycles to help remove tough stains, as well
as a steam boost for added cleaning power. An integrated
heater helps to maintain optimal wash temperatures. See the
“Cycle Guide” for cycles that allow the Steam Clean option.
Load & Go™ Dispenser Drawer (on some models)
The Load & Go™ dispenser drawer gives you the convenience
of automatically adding HE detergent, liquid chlorine bleach,
and liquid fabric softener to the wash load at the proper time.
See “Using the Load & Go™ Dispenser Drawer” for information
on using the dispenser drawer.
C
A
Powdered High Efficiency “HE” detergent
A
compartment
This compartment holds powdered HE detergent
for a single load.
Liquid fabric softener compartment
B
Automatically dilutes and dispenses liquid fabric
softener at the optimum time in the cycle.
n
Use only liquid fabric softener in this dispenser.
Liquid chlorine bleach compartment
C
Automatically dilutes and dispenses liquid chlorine
bleach at the optimum time during the first rinse after
the wash cycle. This compartment cannot dilute
powdered bleach.
B
D
Dispenser Drawer (on some models)
The dispenser drawer gives you the convenience
of adding HE detergent, liquid chlorine bleach,
and liquid fabric softener to the wash load at the
proper time. See “Using the Dispenser Drawer”
for information on using the dispenser drawer.
C
B
E
Load & Go™ Liquid High Efficiency “HE”
D
detergent cartridge
Each dispenser cartridge holds up to 18.5 oz. (550 ml)
of liquid HE detergent, enough for up to 36† loads,
depending on cycle and detergent concentration.
The cartridge fits into compartment (B) of the dispenser
drawer for convenient loading.
n
Change detergent concentration setting
if detergent used is different than factory
preset of 2x concentration. See “About
Detergent Concentration” section.
n
Change water hardness setting if
desired level is different than factory
preset of Normal.
Liquid High Efficiency “HE” detergent compartment
E
This compartment holds liquid or powdered HE
detergent for your main wash cycle.
†
The number of loads will vary, depending on detergent concentration, load size,
cycle used, and soil level. The maximum capacity of up to 36 loads requires use
of 6x concentration detergent.
7
CYCLE STATUS LIGHTS
The Cycle Status Lights show the progress of a cycle. At each
stage of the process, you may notice sounds or pauses that
are different from traditional washers.
Load & Go™ Dispenser Drawer
This will be lit when the washer is on with the dispenser
drawer closed and the cartridge in place. If the cartridge is
removed and the drawer is closed, Load & Go will not light.
Detergent Level
Low – This will light (yellow) if there is enough detergent
in the Load & Go™ cartridge for only a few more cycles.
Empty – This will light (red) if there is no detergent in the
Load & Go™ cartridge.
Door Locked
Door Locked will light to indicate that the door is locked and
cannot be opened without first pausing or canceling the cycle.
Add Garment
When Add Garment is lit, you may pause the washer, open
the door, and add items. Touch and hold the Start button
to start the washer again.
Dispensing
This will light when the detergent is being dispensed.
Done
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
Delay Wash
This will light when a delay time has been set.
Sensing
When the Start button is touched, the washer will first perform
a self-test on the door lock mechanism and the sensing light
will come on. You will hear a click, the drum will make a
partial turn, and the door will click again as it unlocks briefly.
The door will click one more time when it locks again.
Once the door has locked the second time, the washer
will begin tumbling and adding water. This sensing process
will continue throughout the cycle. You may also hear water
flowing through the dispenser, adding detergent to the load.
After the load size is sensed, the estimated time based on
load size will be displayed. The actual cycle time may be
lengthened; however, the display will continue to show the
estimated time.
The sensing light will blink once a second at various times
during the cycle, such as when the washer is reducing
extra suds.
Steaming
This will light to show that the cycle is using steam for added
cleaning power.
FanFresh® Option
The FanFresh indicator will light when the FanFresh® option
is active. During this time, the washer will occasionally tumble
the load while a fan circulates fresh air through the washer.
8
Cycle Guide
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle, options, and settings
that best fit the load being washed. Not all settings are available with each cycle, and some options cannot be used together.
Not all cycles and options are available on all models.
Load Size Recommendations
For best results, follow the load size recommendations noted for each cycle.
Small load: Fill the washer drum with 3–4 items, not more
Large load: Fill the washer drum up to about ¾ full.
than ¼ full.
Medium load: Fill the washer drum up to about ½ full.
Extra-large load: Fill the washer drum, but make
sure clothes can tumble freely. For best results, avoid
packing tightly.
Items to wash
using default
cycle settings:
Normally soiled
cottons, linens,
sheets, and
mixed garment
loads
Heavily soiled
white fabrics
and garments
Cycle:
Temperature:*
Wash
NormalExtra Hot
Hot
Warm
Cool
Cold
WhitesExtra Hot
Hot
Warm
Cool
Cold
Spin
Speed:***
Extra Fast
Fast
Medium
Off
Extra Fast
Fast
Medium
Slow
Off
Soil
Level:
Extra Heavy
Heavy
Normal
Light
Extra Heavy
Heavy
Normal
Light
Available
Options:
Steam Clean**
FanFresh®
Extra Rinse
PreSoak
Delay Wash
Steam Clean**
EcoBoost
FanFresh
Extra Rinse
PreSoak
™
®
Delay Wash
Sturdy colorfast
fabrics and
heavily soiled
garments
Heavy
Duty
Extra Hot
Hot
Warm
Cool
Cold
Extra Fast
Fast
Medium
Slow
Off
Extra Heavy
Heavy
Normal
Light
Steam Clean**
EcoBoost
FanFresh
Extra Rinse
PreSoak
™
®
Delay Wash
Sturdy towels
and wash cloths
TowelsExtra Hot
Hot
Warm
Cool
Cold
Extra Fast
Fast
Medium
Slow
Off
Extra Heavy
Heavy
Normal
Light
Steam Clean**
EcoBoost
FanFresh
Extra Rinse
PreSoak
™
®
Delay Wash
Bright or darkly
colored cottons,
linens, casual
and mixed
loads
* All temperature selections feature a Cold rinse.
** The Steam Clean option is only available when a Warm, Hot, or Extra Hot water temperature is selected.
*** Spin speed varies by model.
ColorlastExtra Hot
Hot
Warm
Cool
Cold
Extra Fast
Fast
Medium
Slow
Off
Extra Heavy
Heavy
Normal
Light
Cycle Details:
This cycle combines
medium-speed tumbling
and an extra-fast-speed
spin. This cycle is designed
to provide the most energy
efficiency.
Uses a longer wash time
with fast-speed tumbling,
extra rinsing, and an extra
fast-speed spin to provide
optimal cleaning and rinsing
when bleach is used.
Fast-speed tumbling and
an extra-fast-speed final
spin help provide optimal
cleaning and reduce
drying times.
Provides fast-speed
tumbling, longer wash time,
normal rinsing, and an extra
fast-speed spin to shorten
drying time.
This cycle combines gentle
tumbling and soaking to
protect colors and provide
a gentle cleaning.
Continued on next page
9
Items to wash
using default
cycle settings:
Clothing,
bedding and
towels requiring
sanitization
No clothes in
washer
Wet load of
clothes
Cycle:
Sanitize
Eco Sanitize
with Oxi
Clean
Washer
with affresh
Drain & SpinN/A
®
Wash
Temperature:*
Extra HotExtra Fast
HotFast
Spin
Speed:***
Fast
Medium
Slow
Off
Medium
Slow
Off
Extra Fast
Fast
Medium
Slow
Off
Soil
Level:
Extra Heavy
Heavy
Normal
Light
Heavy
Normal
Light
N/AFanFresh
Steam Clean**
Available
Options:
FanFresh
Extra Rinse
Delay Wash
FanFresh
Extra Rinse
Delay Wash
Delay Wash
Cycle Details:
This cycle eliminates
®
®
®
99.99% of the most
common bacteria
found in clothes,
sheets, and towels.
The extra hot wash
temperature ensures
sanitization. Check
recommended wash
temperature of your
items. Bacteria tested
were K. pneumonia,
P. aureginosa, and
S. aureus.
This cycle eliminates
99.99% of the most
common bacteria
found in clothes,
sheets, and towels.
Using the highest wash
temperature available
and adding a powdered
Oxi product in the drum
ensures sanitization.
Check recommended
wash temperature of
your items and use
the amount of Oxi
recommended by
the manufacturer.
Bacteria tested
were K. pneumonia,
P. aureginosa, and
S. aureus.
Use this cycle every 30
washes to keep the inside of
your washer fresh and clean.
This cycle uses a higher
water level. Use with affresh
washer cleaner tablet or liquid
chlorine bleach to thoroughly
clean the inside of your
washer. This cycle should not
be interrupted. See “Washer
Care.”
IMPORTANT: Do not place
garments or other items in
the washer during the Clean
Washer with affresh® cycle.
Use this cycle with an empty
wash tub. See “Washer Care”
in “Washer Maintenance.”
Use Drain & Spin to
remove excess water
from the load. Spin
speed can be set
to a slower setting.
®
* All temperature selections feature a Cold rinse.
** The Steam Clean option is only available when a Warm, Hot, or Extra Hot water temperature is selected.
*** Spin speed varies by model.
10
Continued on next page
Loading...
+ 23 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.