THANK YOU for purchasing this high-quality product. Register your range at www.whirlpool.com. In Canada, register your range
at www.whirlpool.ca.
For future reference, please make a note of your product model and serial numbers. These can be found on the label located on the
upper-left side of the front frame.
Model Number___________________________________________ Serial Number___________________________________________
Table of Contents
RANGE SAFETY .............................................................................2
The Anti-Tip Bracket ....................................................................3
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
2
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the
anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
Anti-Tip
Bracket
Range Foot
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
■ WARNING: TO REDUCE THE RISK OF TIPPING OF
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR OR WALL, AND
SLIDE RANGE BACK SO REAR RANGE FOOT IS UNDER
ANTI-TIP BRACKET.
■ WARNING: NEVER use this appliance as a space
heater to heat or warm the room. Doing so may result in
carbon monoxide poisoning and overheating of the oven.
■ WARNING: NEVER cover any slots, holes or passages
in the oven bottom or cover an entire rack with materials
such as aluminum foil. Doing so blocks air flow through the
oven and may cause carbon monoxide poisoning.
Aluminum foil linings may also trap heat, causing a fire
hazard.
■ CAUTION:
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be
seriously injured.
Do not store items of interest to children in
■ Proper Installation – The range, when installed, must be
electrically grounded in accordance with local codes or, in
the absence of local codes, with the
Code, ANSI/NFPA 70
electrically grounded in accordance with Canadian
Electrical Code. Be sure the range is properly installed and
grounded by a qualified technician.
■ This range is equipped with a three-prong grounding plug
for your protection against shock hazard and should be
plugged directly into a properly grounded receptacle. Do
not cut or remove the grounding prong from this plug.
■ Disconnect power before servicing.
■ Injuries may result from the misuse of appliance doors or
drawers such as stepping, leaning, or sitting on the doors
or drawers.
■ Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
■ Storage in or on the Range – Flammable materials should
not be stored in an oven or near surface units.
■ Top burner flame size should be adjusted so it does not
extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
■ Before Self-Cleaning the Oven – Remove broiler pan and
other utensils. Wipe off all excessive spillage before
initiating the cleaning cycle.
. In Canada, the range must be
National Electrical
SAVE THESE INSTRUCTIONS
3
FEATURE GUIDE
This manual covers several models. Your model may have some or all of the items listed. Refer to this manual or Frequently Asked
Questions (FAQs) section of our website at www.whirlpool.com for more detailed instructions. In Canada, reference the Customer
Service section at www.whirlpool.ca.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
KeypadFeatureInstructions
CLOCKClock
LIGHTOven cavity light
TIMER SET/OFFOven timer
StartCooking start
CancelRange function
The Clock uses a 12-hour cycle.
1. Check that the oven is off.
2. Press CLOCK.
3. Press the Temp/Time up or down arrow keypad to set the hours. Press CLOCK to switch
to the minutes. Press the Temp/Time up or down arrow keypad to set theminutes.
4. Press CLOCK or the Start keypad.
While the oven door is closed, press LIGHT to turn the light on and off. The oven light
willcome on when the oven door is opened. The oven light will not come on during the
Self-Cleaningcycle.
The Timer can be set in hours or minutes up to 9 hours and 59 minutes.
1. Press TIMER SET/OFF.
2. Press the Temp/Time up or down arrow keypad to set the length of time.
3. Press the Start keypad to begin the countdown. If enabled, end-of-cycle tones will sound
at end ofcountdown.
4. Press TIMER SET/OFF to cancel the Timer. Do not press the Cancel keypad because the
oven will turn off.
The Start keypad begins any oven function. If the Start keypad is not pressed within
10 seconds, a tone will sound and The Start keypad will blink until pressed or canceled.
If Start is not pressed within 30 seconds after pressing a keypad, the function is canceled
and the time of day is displayed.
The Cancel keypad stops any function except the Timer and Oven Control Lockout.
TEMP/TIMETemperature
and time adjust
BAKEBaking and
roasting
4
The Temp/Time up and down arrow keypads are used to adjust time and
temperaturesettings.
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad until desired temperature is reached.
Atone will sound if the minimum or maximum temperature is reached.
3. Press the Start keypad.
4. To change the temperature, repeat Step 2. Press the Start keypad.
5. Press the Cancel keypad when nished.
NOTE: The convection fan will shut off when the oven door is opened. If the oven door
remains open for too long, the heating elements will shut off until the oven door is closed. All
timers, including any active Cook Time or Timed Cook functions, will continue to count down.
KeypadFeatureInstructions
CONVECT BAKEConvection
baking and
roasting
FROZEN BAKEPrepackaged
food
BROILBroiling
KEEP WARMHold warm
DELAY STARTDelayed start
COOK TIMETimed cooking
1. Press CONVECT BAKE.
2. Press the Temp/Time up or down arrow keypad until desired temperature is reached.
Atone will sound if the minimum or maximum temperature is reached.
3. Press the Start keypad.
4. To change the temperature, repeat Step 2. Press the Start keypad.
5. Press the Cancel keypad when nished.
NOTE: The convection fan will shut off when the oven door is opened. If the oven door
remains open for too long, the heating elements will shut off until the oven door is closed. All
timers, including any active Cook Time or Timed Cook functions, will continue to count down.
1. Position the food on a at rack in the oven on rack position 3 or 4. See the “Positioning
Racks and Bakeware” section.
NOTE: Cook only 1 package of frozen food at a time when using Frozen Bake™
Technology.
2. Press FROZEN BAKE LASAGNA or PIZZA.
3. Press the Temp/Time up or down arrow keypad to set the temperature as recommended
on the food packaging.
4. Press COOK TIME.
5. Press the Temp/Time up or down arrow keypad to set the maximum cook time as
recommended on the food packaging.
6. Press the Start keypad. The range will calculate the best cook time.
NOTE: The cook time that appears in the display is the estimated required cook time as
calculated by the oven control. It may be different than the time you entered. A beep will
alert you to check the food’s doneness with at least 2 minutes remaining on the timer.
Follow the prompts on the display to select more time if desired.
7. Press the Start keypad to start the calculated time.
8. At the end of the cook time, a beep will alert you to check the food’s doneness. When
“End” is displayed and is ashing, you can add more time, if desired. Press the up or
down arrow keypad to set the time, then press START. If more time is not added, the bake
element will turn off.
NOTE: Pressing Cancel will exit the Frozen Bake™ cycle.
9. Press the Cancel keypad when nished.
NOTE: The convection fan will shut off when the oven door is opened. If the oven door
remains open for too long, the heating elements will shut off until the oven door is closed. All
timers, including any active Cook Time or Timed Cook functions, will continue to count down.
1. Press BROIL.
2. Press the Temp/Time up or down arrow keypad until desired temperature is reached.
Atone will sound if the minimum or maximum temperature is reached.
3. Press the Start keypad.
4. Preheat the oven for ve minutes, unless otherwise recommended by recipe. Position
cookware in the oven and close the oven door.
5. To change the temperature, repeat Step 2 and press the Start keypad.
6. Press the Cancel keypad when nished.
NOTE: The convection fan will shut off when the oven door is opened. If the oven door
remains open for too long, the heating elements will shut off until the oven door is closed. All
timers, including any active Cook Time or Timed Cook functions, will continue to count down.
Food must be at serving temperature before placing it in the warmed oven.
1. Press KEEP WARM.
2. Temperature is set at 170°F (75°C). Press the Temp/Time up or down arrow keypad
until desired temperature is reached. A tone will sound if the minimum or maximum
temperature is reached.
3. Press the Start keypad.
4. Press the Cancel keypad when nished.
NOTE: The convection fan will shut off when the oven door is opened. If the oven door
remains open for too long, the heating elements will shut off until the oven door is closed. All
timers, including any active Cook Time or Timed Cook functions, will continue to count down.
Delay Start is used to enter the starting time for an oven function with a delayed start.
Delay Startshould not be used for foods such as breads and cakes because they may
notbakeproperly.
To set a Timed Cook or a Delayed Timed Cook, see “Cook Time” section.
Cook Time allows the oven to be set to turn on at a certain time of day, cook for a set length
of time, and/or shut off automatically.
To set a Timed Cook or a Delayed Timed Cook, see “Cook Time” section.
5
B
A
KeypadFeatureInstructions
CLEANSelf-Cleaning
CONTROL LOCK
(Hold 3 sec)
cycle
Oven and
cooktop control
lockout
See the “Self-Cleaning Cycle” section.
1. Check that the oven and cooktop are off.
2. Press and hold CONTROL LOCK for 3 seconds.
3. A tone will sound and a lock will be displayed.
4. Repeat to unlock. No keypads will function with the controls locked.
COOKTOP USE
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
Electric igniters automatically light the surface burners when
control knobs are turned to (Ignite).
Before setting a control knob, place lled cookware on the
grate. Donot operate a burner using empty cookware or
withoutcookware on the grate.
To Set:
1. Push in and turn knob counterclockwise to the Ignite position.
IMPORTANT: All four surface burners will click. Only the
burner
with the control knob turned to the Ignite position will
produce a ame.
2. Turn knob to anywhere between Hi and Lo.
Power Failure
In case of prolonged power failure, the surface burners can
be lit manually. Hold a lit match near a burner and turn knob
counterclockwise to the Ignite position. After the burner lights,
turn knob to setting.
Sealed Surface Burners
A
B
C
A. Burner cap
B. Burner base
C. Alignment pins
IMPORTANT: Do not obstruct the ow of combustion and
ventilation air around the burner grate edges.
Burner cap: Always keep the burner cap in place when using
asurface burner. A clean burner cap will help avoid poor ignition
anduneven ames. Always clean the burner cap after a spillover
and routinely remove and clean the caps according to the
“General Cleaning” section.
Gas tube opening: Gas must ow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil
and do not allow spills, food, cleaning agents, or any other
material to enter the gas tube opening. Keep spillovers out of
thegas tube by always using a burner cap.
D. Igniter
E. Gas tube opening
D
E
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
6
A. 1-11/2" (2.5-3.8 cm)
B. Burner ports
Burner ports: Check burner ames occasionally for proper size
and shape as shown in the previous illustration. A good ame
is blue in color, not yellow. Keep this area free of soil and do not
allow spills, food, cleaning agents, or any other material to enter
the burner ports.
To Clean:
A
B
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Do not use oven cleaners, bleach,
or rust removers.
1. Remove the burner cap from the burner base and clean
according to the “General Cleaning” section.
2. Clean the gas tube opening with a damp cloth.
3. Clean clogged burner ports with a straight pin as shown.
Donot enlarge or distort the port. Do not use a wooden
toothpick. If the burner needs to be adjusted, contact a
trainedrepair specialist.
Burner Size
Select a burner that best ts your cookware. Burner positions will
vary based on the model of your range.
Back of Range
Medium
Oval
Small
4. Replace the burner cap, making sure the alignment pins are
properly aligned with the burner cap.
A. Incorrect
B. Correct
5. Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
Grates
Models WFG525, WFG550, and WFG535
The grates on this range cover the full width of the cooktop. The
three grates interlock, using the hook formed into the grates. The
at end of the middle grate drops onto the hooks on the other
grates as shown in the following illustration.
To install the grates, place the grate embossed “Left” on the left
side of the cooktop. Place the grate embossed “Right” on the right
side of the cooktop. Place the middle grate last, as shown in the
previous illustration.
Extra
Large
Large
Front of Range
Burner SizeRecommended Use
Small
Medium
Large
Extra-Large
Oval
■ Low-heat cooking
■ Melting chocolate or butter
■ Multipurpose burner
■ For large cookware
■ For large cookware
■ Most powerful burner
■ For longer dishes
Cookware
IMPORTANT: Do not leave empty cookware on a hot surface
cooking area, element, or surface burner.
Ideal cookware should have a at bottom, straight sides, and a
well-tting lid, and the material should be of medium-to-heavy
thickness.
Rough nishes may scratch the cooktop or grates. Aluminum and
copper may be used as a core or base in cookware.
Cookware material is a factor in how quickly and evenly heat is
transferred which affects cooking results.
Cookware with nonstick surfaces should not be used under the
broiler.
Check for atness by placing the straight edge of a ruler across
the bottom of the cookware. While you rotate the ruler, no space
or light should be visible between it and the cookware.
1
2
3
4
1
5
6
7
2
8
9
3
1 0
1 1
1 2
4
1 3
1 4
5
1 5
1 6
6
1 7
1 8
1 9
7
2 0
Model WFG510
The grates must be properly positioned before cooking. Improper
installation of the grates may result in chipping of the cooktop.
Although the grates are durable, they will gradually lose their shine
due to exposure to high temperatures.
7
Use the following chart as a guide for cookware material
characteristics.
CookwareCharacteristics
Aluminum
■ Heats quickly and evenly.
■ Suitable for all types of cooking.
■ Medium or heavy thickness is best
formost cooking tasks.
Cast iron
Ceramic or
ceramic glass
■ Heats slowly and evenly.
■ Good for browning and frying.
■ Maintains heat for slow cooking.
■ Follow manufacturer’s instructions.
■ Heats slowly but unevenly.
■ Ideal results on low- to medium-heat
settings.
Copper
■ Heats very quickly and evenly.
■ May leave copper residues which may
be diminished if cleaned immediately
after cooking.
Earthenware/
Stoneware
Porcelain
■ Follow manufacturer’s instructions.
■ Use on low-heat settings.
■ See stainless steel or cast iron.
enamel-on-steel
or cast iron
Stainless steel
■ Heats quickly but unevenly.
■ A core or base of aluminum or copper
on stainless steel provides even
heating.
For best results, the cookware should be centered above the
burner with the bottom sitting level on the grate. The ame should
be adjusted so that it does not extend up the sides of the pan.
OVEN USE
The normal operation of the range will include several noises that
may be heard each time the bake or broil burners ignite during the
cooking cycle:
■ Gas valves may make a “popping” sound when opening
or closing.
■ Igniters will “click” several times until a ame is sensed.
■ A “poof” sound is heard when a bake or broil burner ignites.
Odors and smoke are normal when the oven is used the rst few
times or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive
tothe fumes given off. Exposure to the fumes may result in
deathto certain birds. Always move birds to another closed
andwell-ventilated room.
NOTE: The convection fan will shut off when the oven door is
opened. If the oven door remains open for too long, the heating
elements will shut off until the oven door is closed. All timers,
including any active Cook Time or Timed Cook functions, will
continue to count down.
Electronic Oven Controls
Control Display
The display will ash when powered up or after a power loss.
Press the Cancel keypad to clear. When oven is not in use, the
time of day isdisplayed.
Fahrenheit and Celsius
The temperature is preset to Fahrenheit but can be changed
toCelsius.
To change: Press and hold the Temp/Time up arrow keypad for
5seconds. “°C”or“°F” will appear on the display. Repeat to
change back.
To exit mode, press the Cancel keypad.
Home Canning
When canning for long periods, alternate the use of surface
burners between batches. This allows time for the most-recently
used areas to cool.
■ Center the canner on the grate above the burner.
■ Do not place canner on two surface burners at the same time.
■ For more information, contact your local agricultural extension
ofce or refer to published home canning guides. Companies
that manufacture home canning products can also offer
assistance.
Keypress Tones
Activates or turns off the tones when a keypad is pressed.
To change: Press and hold LIGHT for 5 seconds. Repeatto
change back.
To exit mode, press the Cancel keypad.
Demo Mode
IMPORTANT: This feature is intended for use on the sales oor
with 120 V power connection and permits the control features
to be demonstrated without heating elements turning on. If this
feature is activated, the oven will not work.
To change: Press the Cancel keypad, the Cancel keypad, the
Temp/Time up arrow keypad, TIMER SET/OFF. Repeat to change
back and end Demo mode.
Tones
Tones are audible signals, indicating the following:
Basic Functions
One Tone
■ Valid keypad press
■ Oven is preheated (long tone).
■ Function has been entered.
■ Reminder, repeating every 20 seconds after the
end-of-cycle tones
Three Tones
■ Invalid keypad press.
Four Tones
■ End of cycle
8
Oven Temperature Control
IMPORTANT: Do not use a thermometer to measure oven
temperature. Elements will cycle on and off as needed to provide
consistent temperature but may run slightly hot or cool at any
point in time due to this cycling. Most thermometers are slow
to react to temperature change and will not provide an accurate
reading due to this cycling.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature can
be adjusted to personalize it for your cooking needs. It can be
changed in Fahrenheit or Celsius.
To Adjust Oven Temperature:
1. Press and hold the Temp/Time down arrow keypad for
5seconds until the ovendisplay shows the current setting,
forexample “0°FCAL” or “00.”
2. Press the Temp/Time up or down arrow keypad toincrease
or to decrease the temperature in 5°F (3°C) amounts. The
adjustment can be set between 30°F (18°C) and-30°F(-18°C).
3. Press the Start keypad.
Sabbath Mode
(on some models)
For guidance on usage and a complete list of models with
Sabbath mode, visit www.star-k.org.
The Sabbath mode sets the oven to remain on in a Bake setting
until turned off. A Timed Bake can also be set to keep the oven on
for only part of the Sabbath. The Oven Control Lockout feature will
be disabled during the Sabbath mode. After the Sabbath mode is
set, no tones will sound, the display will not show the temperature,
the Kitchen Timer mode will be canceled (ifactive), and only the
following keypads will function:
■ Temp/Time up and down arrow keypads
■ Cancel
When the oven door is opened or closed, the oven light will not
turn on or off and the heating elements will not turn on or off
immediately.
When power is restored after a power failure, the oven will return
to Sabbath mode and remain Sabbath compliant with the bake
elements off until the Cancel keypad is pressed.
Pressing the Cancel keypad at any time returns the oven to the
normal cooking mode (not Sabbath compliant).
Before entering the Sabbath mode, it must be decided if the oven
light is to be on or off for the entire Sabbath mode period. If the
light is on when entering Sabbath mode, it will remain on for the
entire time Sabbath mode is in use. If the light is off when entering
Sabbath mode, it will remain off for the entire time Sabbath mode
is in use. Opening the oven door or pressing LIGHT will not affect
the oven light once Sabbath mode has been entered.
On the Holiday, the oven temperature can be changed once the
oven is in Sabbath mode by pressing the Temp/Time up or down
arrow keypad. The oven temperature will change 25°F (14°C) each
time the Temp/Time up and down arrow keypads are pressed.
Press the Start keypad to activate the new temperature. The
display will not change and there will be no sounds during this
adjustment.
To Activate and Bake Using Sabbath Mode:
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad.
3. Press the Start keypad.
4. Press and hold TIMER SET/OFF for 5 seconds. “SAb” will ash
in the display.
5. Press the Start keypad while “SAb” is ashing to enter
Sabbath mode; otherwise, the entire cycle cancels out. “SAb”
will stop ashing and remain on in the display. The oven is now
in Sabbath mode and is Sabbath compliant.
Pressing the Cancel keypad at any time returns the oven to the
normal cooking mode (not Sabbath compliant).
NOTE: If “SAb” does not appear in your display, the Sabbath
mode is not active. After Sabbath mode is deactivated, you must
activate Sabbath mode by completing steps 1 through 5.
To Set a Timed Bake Using Sabbath Mode
(on some models):
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad to enter
atemperature other than the one displayed.
3. Press COOK TIME. The Cook Time oven indicator light
willlight up.
4. Press the Temp/Time up or down arrow keypad to enter
acooktimelength.
5. Press the Start keypad.
6. Press and hold TIMER SET/OFF for 5 seconds. “SAb” will ash
in the display.
7. Press the Start keypad while “SAb” is ashing to enter
Sabbath mode; otherwise, the entire cycle cancels out. “SAb”
will stop ashing and remain on in the display. The oven is now
in Sabbath mode and is Sabbath compliant. The Bake, On,
andCook Time indicator lights will be displayed.
When the set cook time ends, the oven will shut off automatically
and the indicator lights will turn off, indicating the end of the cycle.
Pressing the Cancel keypad at any time returns the oven to the
normal cooking mode (not Sabbath mode compliant).
NOTE: If “SAb” does not appear in your display, the Sabbath
mode is not active. After Sabbath mode is deactivated, you must
activate Sabbath mode by completing steps 1 through 5.
To Set a Delayed Timed Bake Using Sabbath Mode
(on some models):
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad to enter
atemperature other than the one displayed.
3. Press COOK TIME. The Cook Time oven indicator light
willlight up.
4. Press the Temp/Time up or down arrow keypad to enter
acooktimelength.
5. Press DELAY START. The Delay indicator light will light up.
6. Press the Temp/Time up or down arrow keypad to enter a
start time.
7. Press the Start keypad.
8. Press and hold TIMER SET/OFF for 5 seconds. “SAb” will ash
in the display.
9. Press the Start keypad while “SAb” is ashing to enter
Sabbath mode; otherwise, the entire cycle cancels out. “SAb”
will stop ashing and remain on in the display. The oven is now
in Sabbath mode and is Sabbath compliant. The On and Delay
indicator lights will be displayed.
When the start time is reached, the Bake, On, and Cook Time
indicator lights will automatically turn on. When the set cook time
ends, the oven will shut off automatically and the indicator lights
will turn off, indicating the end of the cycle.
Pressing the Cancel keypad at any time returns the oven to the
normal cooking mode (not Sabbath mode compliant).
NOTE: If “SAb” does not appear in your display, the Sabbath
mode is not active. After Sabbath mode is deactivated, you must
activate Sabbath mode by completing steps 1 through 5.
9
Keep Warm
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
NOTE: The convection fan will shut off when the oven door is
opened. If the oven door remains open for too long, the heating
elements will shut off until the oven door is closed. All timers,
including any active Cook Time or Timed Cook functions, will
continue to count down.
IMPORTANT: Food must be at serving temperature before placing
it in the warmed oven. Food may be held up to 1 hour; however,
breads and casseroles may become too dry if left in the oven
during the Keep Warm function. For best results, coverfood.
The Keep Warm feature allows hot cooked foods to stay at
servingtemperature.
To Use:
1. Press KEEP WARM.
2. Press the Temp/Time up or down arrow keypad until desired
temperature is reached. A tone will sound if the minimum or
maximum temperature is reached.
3. Press the Start keypad.
4. Place food in the oven.
5. Press the Cancel keypad when nished.
NOTE: The temperature may be changed at any time by pressing
the Temp/Time up or down arrow keypad to reach the desired
temperature and then pressing the Start keypad.
Rack Positions
Rack 5: Toasting bread or broiling thin, non-fatty foods
Rack 4: two-rack baking and broiling
Rack 3: Most baked goods on a cookie sheet, mufn pan,
convenience foods, and two-rack baking
Rack 1: Roasting large and small cuts of meat and poultry
Multiple Rack Cooking
Two-rack: Use rack positions 2 and 4 or 2 and 5.
Baking Cookies and Layer Cakes on Two Racks
Baking Layer Cakes
For best results when baking cakes on two racks, use the Bake
function, a at rack in rack position 4, and a at rack in rack
position 2. Place the cakes on the racks as shown. Keep at least
3" (7.6 cm) of space between the front of the racks and the front
cakes.
Baking Cookies on Two Racks
For best results when baking cookies on two racks, use the
Convect Bake function and place at racks in positions 2 and 5.
Oven Vent
A
Aluminum Foil
IMPORTANT: To avoid permanent damage to the oven bottom
nish, do not line the oven bottom with any type of foil or liner.
For best cooking results, do not cover entire oven rack with foil
because air must be able to move freely.
Positioning Racks and Bakeware
IMPORTANT: To avoid permanent damage to the porcelain
nish, do not place food or bakeware directly on the oven door
orbottom.
Bakeware
To cook food evenly, hot air must be able to circulate. Allow
2"(5cm) of space around bakeware and oven walls. Make
surethatno bakeware piece is directly over another.
Racks
■ Position racks before turning on the oven.
■ Do not position racks with bakeware on them.
■ Make sure racks are level.
To move a rack, pull it out to the stop position, raise the front
edge, and then lift out. Use the following illustration asa guide.
5
4
3
2
1
A. Oven vent
The oven vent releases hot air and moisture from the oven
andshould not be blocked or covered. Blocking or covering the
oven vent will cause poor air circulation, affecting cooking and
cleaning results. Do not set plastics, paper, or other items that
could melt or burn near the oven vent.
10
Baking and Roasting
Preheating
When beginning a Bake cycle, the oven will begin preheating
after Start is pressed. The oven will take approximately 12 to
15 minutes to reach 350°F (177°C) with all of the oven racks
provided with your oven inside the oven cavity. Higher
temperatures will take longer to preheat. The preheat cycle
rapidly increases the oven temperature. The actual oven
temperature will go above your set temperature to offset the heat
lost when your oven door is opened to insert food. This ensures
that when you place your food in the oven, the oven will begin at
the proper temperature. Insert your food when the preheat tone
sounds. Do not open the door during preheat before the tone
sounds.
Oven Temperature
While in use, the oven elements will cycle on and off as needed
to maintain a consistent temperature, but they may run slightly
hot or cool at any point in time due to this cycling. Opening the
oven door while in use will release the hot air and cool the oven
which could impact the cooking time and performance. It is
recommended to use the oven light to monitor cooking progress.
NOTE: On models with convection, the convection fan may run in
the non-convection Bake mode to improve oven performance.
The convection fan will shut off when the oven door is opened.
If the oven door remains open for too long, the heating elements
will shut off until the oven door is closed. All timers, including any
active Cook Time or Timed Cook functions, will continue to count
down.
Temperature Management System
The Temperature Management System electronically regulates the
oven heat levels during preheat and bake to maintain a precise
temperature range for optimal cooking results. The bake and broil
elements or burners cycle on and off in intervals. On convection
range models, the fan will run while preheating and may be cycled
on and off for short intervals during bake to provide the best
results. This feature is automatically activated when the oven is
in use.
Before baking and roasting, position racks according to the
“Positioning Racks and Bakeware” section. When roasting, it is not
necessary to wait for the oven preheat cycle to end before putting
food in unless it is recommended in the recipe.
Broiling
NOTE: The convection fan will shut off when the oven door is
opened. If the oven door remains open for too long, the heating
elements will shut off until the oven door is closed. All timers,
including any active Cook Time or Timed Cook functions, will
continue to count down.
When broiling, preheat the oven for 5 minutes before putting food
in unless recommended otherwise in the recipe. Position food on
grid in a broiler pan, then place it in the center of the oven rack.
IMPORTANT: Close the door to ensure proper broiling
temperature.
Changing the temperature when broiling allows more precise
control when cooking. The lower the broil setting is, the slower the
cooking. Thicker cuts and unevenly shaped pieces of meat, sh,
and poultry may cook better at lower broil settings. Use racks 4
or 5 for broiling. Refer to the “Positioning Racks and Bakeware”
section for more information.
On lower settings, the broil element will cycle on and off to
maintain the proper temperature.
■ For best results, use a broiler pan and grid. It is designed to
drain juices and help avoid spatter and smoke.
If you would like to purchase a broiler pan, one may be
ordered. Please refer to the “Accessories” section for
moreinformation.
NOTE: Odors and smoke are normal the rst few times the oven
isused or if the oven is heavily soiled.
Convection Baking and Roasting
NOTE: The convection fan will shut off when the oven door is
opened. If the oven door remains open for too long, the heating
elements will shut off until the oven door is closed. All timers,
including any active Cook Time or Timed Cook functions, will
continue to count down.
During convection baking or roasting, the bake and broil elements
or burners cycle on and off in intervals to maintain the oven
temperature while the fan circulates the hot air.
If the oven door is opened during convection baking or roasting,
the fan will turn off immediately. It will come back on when the
oven door is closed.
NOTE: The convection fan will turn on approximately 5 minutes
into any convection cycle.
Cook Time
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
To Set a Timed Cook:
1. Press BAKE. The Bake indicator light will light up.
2. Press the Temp/Time up or down arrow keypad to enter
atemperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will
lightup.
4. Press the Temp/Time up or down arrow keypad to enter the
length of time to cook.
5. Press the Start keypad. The display will count down the time.
When the time ends, the oven will shut off automatically.
6. Press the Cancel keypad to clear the display.
To Set a Delayed Timed Cook:
Before setting, make sure the clock is set to the correct time
of day. See the “Clock” keypad feature in the “Feature Guide”
section.
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad to enter
atemperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will
lightup.
4. Press the Temp/Time up or down arrow keypad to enter
thelength of time to cook.
5. Press DELAY START. The delay oven indicator light will
light up.
6. Press the Temp/Time up or down arrow keypad to enter
theamount of time until desired start.
7. Press the Start keypad.
When the start time is reached, the oven will automatically turn
on. The temperature and/or time settings can be changed anytime
after pressing the Start keypad by repeating steps 1 through 7.
When the set cook time ends, the oven will shut off automatically.
8. Press the Cancel keypad to clear the display.
11
RANGE CARE
WARNING
Self-Cleaning Cycle
(on some models)
Burn Hazard
Do not touch the oven during the Self-Cleaning cycle.
Keep children away from oven during
Self-Cleaning cycle.
Failure to follow these instructions can result in burns.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off during the Self-Cleaning cycle. Exposure to the
fumes may result in death to certain birds. Always move birds to
another closed and well-ventilated room.
Do not block the oven vent(s) during the Self-Cleaning cycle.
Air must be able to move freely. Depending on your model, see
“OvenVent” section.
Do not clean, rub, damage, or move the oven door gasket.
Prepare Range
■ Remove the broiler pan, grid, cookware and bakeware, all
cooking utensils, oven racks, and aluminum foil and, on some
models, the temperature probe from the oven.
■ Use a damp cloth to clean inside door edge and the 1
(3.8cm) area around the inside oven cavity frame, being
certain not to move or bend the gasket.
■ Remove plastic items from the cooktop because they
maymelt.
■ Remove all items from the storage drawer.
1
/2"
How the Cycle Works
IMPORTANT: The heating and cooling of porcelain on steel in the
oven may result in discoloring, loss of gloss, hairline cracks, and
popping sounds.
Before cleaning, make sure the door is completely closed or the
door will not lock and the Self-Cleaning cycle will not begin.
Once the oven has completely cooled, remove ash with a damp
cloth. To avoid breaking the glass, do not apply a cool damp cloth
to the inner door glass before it has completely cooled.
To stop the Self-Cleaning cycle at any time, press the Cancel
keypad. Ifthe temperature is too high, the oven door will remain
locked and “cool” and “ ” will be displayed. The cooling fan may
continue to run.
The oven light will not function during the Self-Cleaning cycle.
Electronic Oven Control with Adjustable Clean Time
(on some models)
The Self-Cleaning cycle is time adjustable between 2 hours
30 minutes and 4 hours 30 minutes in 30-minute increments.
Suggested clean times are 2 hours 30 minutes for light soil and
4hours 30 minutes for heavy soil. Last 30 min. are for cool down.
To Self-Clean:
1. Press CLEAN.
2. Press the Temp/Time up or down arrow keypad to enter the
desired Self-Cleaning cycle time.
3. Press the Start keypad.
The oven door will automatically lock. The Door Locked and
Clean indicator lights will be displayed. The time remaining
willalso be displayed.
4. When the Self-Cleaning cycle is complete and the oven cools,
the Door Locked and Clean indicator lights will turn off.
5. When the oven is completely cooled, remove ash with a
dampcloth.
To exit the Self-Cleaning cycle before completed, press the
Cancel keypad. The door will unlock once the oven cools.
12
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Always follow label instructions
on cleaning products. For additional information, you can visit
the Frequently Asked Questions (FAQs) section of our website at
www.whirlpool.ca.
Soap, water, and a soft cloth or sponge are suggested rst
unlessotherwise noted.
EXTERIOR PORCELAIN ENAMEL SURFACES
(on some models)
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire range is cool. These spills may
affect the nish.
Cleaning Method:
■ Glass cleaner, mild liquid cleaner, or nonabrasive
scrubbingpad:
Gently clean around the model/serial/rating plate
becausescrubbing may remove numbers.
■ Affresh
STAINLESS STEEL (on some models)
NOTE: To avoid damage to stainless steel surfaces, do not use
soap-lled scouring pads, abrasive cleaners, Cooktop Cleaner,
steel-wool pads, gritty washcloths, or abrasive paper towels.
Damage may occur to stainless steel surfaces, even with one-time
or limited use.
Cleaning Method:
Rub in direction of grain to avoid damaging.
■ Affresh
METALLIC PAINT (on some models)
Do not use abrasive cleaners, cleaners with bleach, rust removers,
ammonia, or sodium hydroxide (lye) because the paintsurface
maystain.
PORCELAIN-COATED GRATES AND CAPS
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the cooktop, grates, and caps are cool.
These spills may affect the nish.
To avoid chipping, do not bang grates and caps against each
other or hard surfaces such as cast iron cookware.
Do not reassemble caps on burners while wet.
Do not clean in the Self-Cleaning cycle.
Cleaning Method:
■ Nonabrasive plastic scrubbing pad and mildly abrasive
■ Dishwasher (grates only, not caps):
■ Gas Grate and Drip Pan Cleaner Part Number 31617:
SURFACE BURNERS
■ See the “Sealed Surface Burners” section.
®
Kitchen and Appliance Cleaner Part Number
W10355010 (not included):
See the “Accessories” section for more information.
®
Stainless Steel Cleaner Part Number W10355016
(notincluded):
See the “Accessories” section for more information.
cleanser:
Clean as soon as cooktop, grates, and caps are cool.
Use the most-aggressive cycle. Cooked-on soils should be
soaked or scrubbed before going into a dishwasher.
See the “Warranty” section for contact information.
COOKTOP CONTROLS
To avoid damage to the cooktop controls, do not use steel wool,
abrasive cleansers, or oven cleaner.
To avoid damage, do not soak knobs.
When replacing knobs, make sure knobs are in the Off position.
On some models, do not remove seals under knobs.
Cleaning Method:
■ Soap and water:
Pull knobs straight away from control panel to remove.
CONTROL PANEL AND OVEN DOOR EXTERIOR
To avoid damage to the control panel, do not use abrasive
cleaners, steel-wool pads, gritty washcloths, or abrasive
papertowels.
Cleaning Method:
■ Glass cleaner and soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly
onpanel.
■ Affresh
®
Kitchen and Appliance Cleaner Part Number
W10355010 (not included):
See the “Accessories” section for more information.
OVEN RACKS
Cleaning Method:
■ Steel-wool pad
■ For racks that have discolored and are harder to slide,
alightcoating of vegetable oil applied to the rack guides
willhelp them slide.
STORAGE DRAWER
Check that storage drawer is cool and empty before cleaning.
Cleaning Method:
■ Mild detergent
OVEN CAVITY
Do not use oven cleaners on models with Self-Cleaning cycle.
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain. Staining, etching,
pitting,or faint white spots can result.
Cleaning Method:
■ See the “Self-Cleaning Cycle” section.
Oven Light
The oven light is a standard 40 W appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the Off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb, then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
13
TROUBLESHOOTING
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,
referto the warranty page in this manual, or visit producthelp.whirlpool.com. In Canada, visit www.whirlpool.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada:
Whirlpool Brand Home Appliances
Customer eXperience Centre
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B
Operation
ProblemPossible Causes and/or Solutions
Nothing will operate
Surface burners will not
operate
Surface burner flames
are uneven, yellow, and/
or noisy
Excessive heat around
cookware on cooktop
Cooktop cooking
results not what
expected
Oven will not operate
Oven burner flames are
yellow or noisy
Power supply cord is unplugged: Plug into a grounded 3 prong outlet.
Household fuse is blown or a circuit breaker is tripped: Replace the fuse or reset the circuit breaker.
Ifthe problem continues, call an electrician.
Main or regulator gas shut-off valve is in the Off position: See the Installation Instructions.
The range is improperly connected to the gas supply: Contact a trained repair specialist or see the
Installation Instructions.
The oven is in Self-Cleaning cycle: Surface burners will not operate during Self-Cleaning cycle.
The control knob is not set correctly: Push in knob before turning to a setting.
Air in the gas lines: If this is the rst time the surface burners have been used, turn on any one of the
surface burner knobs to release air from the gas lines.
Clogged burner ports: See the “Sealed Surface Burners” section.
Clogged burner ports: See the “Sealed Surface Burners” section.
Burner caps positioned improperly: See the “Sealed Surface Burners” section.
Range converted improperly: If Propane gas is being used, contact a service technician or see the
“Warranty” section for contact information.
Cookware and ame are not matched: The cookware should be centered above the burner with the
bottom sitting level on the grate. The ame should be adjusted so that it does not extend up the sides
ofthe pan.
Improper cookware: Ideal cookware should have a at bottom, straight sides, and a well-tting lid,
andthematerial should be of a medium-to-heavy thickness.
Control knob set to incorrect heat level: See the “Cooktop Use” section.
Range is not level: Level the range. See the Installation Instructions.
Air in the gas lines: If this is the rst time the oven has been used, turn on any one of the surface burner
knobs to release air from the gas lines.
The range is in Demo mode: Demo mode will deactivate all oven elements. See “Demo Mode” in the
“Electronic Oven Controls” section.
Electronic oven control set incorrectly: See the “Electronic Oven Controls” section.
Range converted improperly: If Propane gas is being used, contact a service technician or see the
“Warranty” section for contact information.
14
ProblemPossible Causes and/or Solutions
Oven temperature too
high or too low
Display shows
messages
Self-Cleaning cycle will
not operate
Oven cooking results
not what expected
Oven temperature needs adjustment: See “Oven Temperature Control” in the “Electronic Oven
Controls”section.
Power failure (Display shows ashing time.): Clear the display. On some models, reset the clock, if
needed. See “Clock” keypad feature in the “Feature Guide” section.
Error code (Display shows letter followed by number.): Depending on your model, press the Cancel
keypad to clear the display. See “Control Display” in the “Electronic Oven Controls” section. If it reappears,
call for service. See the “Warranty” section for contact information.
Range is in Sabbath mode (Display shows “SAb.”): Press the Cancel keypad to exit Sabbath mode.
The oven door is open: Close the oven door all the way.
The function has not been entered: See the “Self-Cleaning Cycle” section.
Self-Cleaning cycle has been run in the past 12 hours: If a Self-Cleaning cycle has been run
orcanceledafter the oven has reached temperature, you will have to wait 12 hours to restart.
Range is not level: Level the range. See the Installation Instructions.
The set temperature was incorrect: Double-check the recipe in a reliable cookbook.
Oven temperature needs adjustment: See “Oven Temperature Control” in the “Electronic Oven
Controls”section.
Oven was not preheated: See the “Baking and Roasting” section.
Racks were positioned improperly: See the “Positioning Racks and Bakeware” section.
Not enough air circulation around bakeware: See the “Positioning Racks and Bakeware” section.
Darker browning of food caused by dull or dark bakeware: Lower oven temperature 25°F (15°C)
ormove rack to a higher position in the oven.
Lighter browning of food caused by shiny or light-colored bakeware: Move rack to a lower position
inthe oven.
Batter distributed unevenly in pan: Check that batter is level in the pan.
Incorrect length of cooking time was used: Adjust cooking time.
Oven door was not closed: Be sure that the bakeware does not keep the door from closing.
Oven door was opened during cooking: Oven peeking releases oven heat and can result in longer
cooking times.
Oven door was open for too long: If the oven door remains open for too long, the heating elements will
shut off until the oven door is closed.
Rack is too close to bake burner, making baked items too brown on bottom: Move rack to higher
position in the oven.
Pie crusts browning too quickly: Use aluminum foil to cover the edge of the crust and/or reduce
bakingtemperature.
Noises
ProblemPossible Causes and/or Solutions
Surface burner making
popping noises
Gas range noises
during Bake and Broil
operations
The following are some
normal sounds with the
explanations.
PopGas valve is opening or cycling on and will make a single pop when it snaps open from the solenoid.
ClickThe igniters will click several times until the ame is detected. These are short clicking sounds like
Woosh of poofBake or broil burner is igniting: This is normal.
Oven burner flames are
yellow or noisy
Wet burner: Allow it to dry.
These sounds are normal operational noises that can be heard each time the bake or broil burners
ignite during the cycle.
It sounds similar to a suction cup being pulled off of a piece of glass: This is normal.
tapping a nail onto a piece of glass: This is normal.
Range converted improperly: If Propane gas is being used, contact a service technician or see the
“Warranty” section for contact information.
15
ACCESSORIES
For accessories in the U.S.A., you can visit our website at www.whirlpool.com or call us at 1-800-253-1301.
In Canada, you can visit our website at www.whirlpool.ca or call us at 1-800-807-6777.
Affresh® Stainless Steel Cleaner
(stainless steel models)
Order Part Number W10355016
Affresh® Stainless Steel Cleaning Wipes
(stainless steel models)
Order Part Number W10355049
Affresh® Kitchen and Appliance Cleaner
Order Part Number W10355010
Granite Cleaner and Polish
Order Part Number W10275756
Gas Grate and Drip Pan Cleaner
Order Part Number 31617
Split Oven Rack
Order Part Number 4396927
Porcelain Broiler Pan and Grid
Order Part Number 4396923
Premium Broiler Pan and Roasting Rack
Order Part Number W10123240
16
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED
TO OBTAIN WARRANTY SERVICE.
WHIRLPOOL®
MAJOR APPLIANCE
LIMITED WARRANTY
Please have the following information available when you call the
Customer eXperience Center:
■ Name, address, and telephone number
■ Model number and serial number
■ A clear, detailed description of the problem
■ Proof of purchase, including dealer or retailer name and address
IF YOU NEED SERVICE:
1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed without
service. Please take a few minutes to review the Troubleshooting section of the Use and Care Guide or visit producthelp.whirlpool.com.
2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers. In the U.S. and Canada, direct all requests for
warranty service to:
Whirlpool Customer eXperience Center
In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.
If outside the 50 United States or Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.
ONE YEAR LIMITED WARRANTY
WHAT IS COVEREDWHAT IS NOT COVERED
For one year from the date of purchase,
when this major appliance is installed,
operated, and maintained according
to instructions attached to or furnished
with the product, Whirlpool Corporation
or Whirlpool Canada LP (hereafter
“Whirlpool”) will pay for factory
specified replacement parts and repair
labor to correct defects in materials or
workmanship that existed when this
major appliance was purchased or, at
its sole discretion, replace the product.
In the event of product replacement,
your appliance will be warranted for
the remaining term of the original unit’s
warranty period.
YOUR SOLE AND EXCLUSIVE
REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE PRODUCT
REPAIR AS PROVIDED HEREIN.
Service must be provided by a
Whirlpool designated service company.
This limited warranty is valid only in
the United States or Canada and
applies only when the major appliance
is used in the country in which it was
purchased. This limited warranty is
effective from the date of original
consumer purchase. Proof of original
purchase date is required to obtain
service under this limited warranty.
1. Commercial, non-residential, multiple-family use, or use inconsistent with published user, operator,
or installation instructions.
2. In-home instruction on how to use your product.
3. Service to correct improper product maintenance or installation, installation not in accordance with
electrical or plumbing codes, or correction of household electrical or plumbing (e.g., house wiring,
fuses, or water inlet hoses).
4. Consumable parts (e.g., light bulbs, batteries, air or water filters, preservation solutions).
5. Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.
6. Conversion of products from natural gas or propane gas.
7. Damage from accident, misuse, abuse, fire, floods, acts of God, or use with products not approved
by Whirlpool.
8. Repairs to parts or systems to correct product damage or defects caused by unauthorized service,
alteration, or modification of the appliance.
9. Cosmetic damage including scratches, dents, chips, and other damage to the appliance finishes,
unless such damage results from defects in materials and workmanship and is reported to Whirlpool
within 30 days.
10. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive environments including,
but not limited to, high salt concentrations, high moisture or humidity, or exposure to chemicals.
11. Food or medicine loss due to product failure.
12. Pickup or delivery. This product is intended for in-home repair.
13. Travel or transportation expenses for service in remote locations where an authorized Whirlpool
servicer is not available.
14. Removal or reinstallation of inaccessible appliances or built-in fixtures (e.g., trim, decorative panels,
flooring, cabinetry, islands, countertops, drywall) that interfere with servicing, removal, or replacement
of the product.
15. Service or parts for appliances with original model/serial numbers removed, altered, or not easily
determined.
The cost of repair or replacement under these excluded circumstances shall be borne by
the customer.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow
limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific
legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations
contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance,
you should ask Whirlpool or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES: EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of
incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you
also may have other rights that vary from state to state or province to province.
03/17
17
Notes
18
Loading...
+ 42 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.