Whirlpool WDT975SAHZ, WDT970SAHB, WDT970SAHW, WDTA75SAHZ User Manual
Undercounter Dishwasher
PRODUCT MODEL NUMBERS
WDF560SAF
WDF760SAD
WDF770SAF
WDT750SAH
WDT755SAH
WDT780SAE
WDT920SAD
WDT970SAH
WDT975SAH
WDT995SAF
WDTA50SAH
WDTA55SAH
WDTA75SAH
DRAIN REQUIREMENTS
■ A new drain hose is supplied with your dishwasher.
If drain hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) that meets all current AHAM/
IAPMO test standards, is resistant to heat and detergent, and
fits the 1" (25 mm) drain connector of the dishwasher.
NOTE: Do not connect multiple drain hoses together.
■ Make sure to connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20" (508 mm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
■ Make sure to use an air gap if the drain hose is connected
to house plumbing lower than 20" (508 mm) above
subfloor or floor.
Use of air gap
Air gap
WATER SUPPLY REQUIREMENTS
■ This dishwasher has a water heating feature and also
requires a connection to a hot water supply line.
■ A hot water line with 20 to 120 psi (138 to 862 kPa)
water pressure can be verified by a licensed plumber.
■ 120°F (49°C) water at dishwasher
3
■
/8" O.D. copper tubing with compression fitting or flexible
braided water supply line. See the “Tools and Parts” section
at the front of the guide for part details and orders.
NOTE: 1/2" minimum plastic tubing is not recommended.
■ A 90° elbow with
■ Do not solder within 6" (152 mm) of the water inlet valve.
■ If installed in new construction, make sure the house
3
/4" hose connection with rubber washer.
water supply lines have been flushed prior to connecting
the dishwasher to remove any debris that may exist in
the supply line.
NOTE: If replacing an existing dishwasher, it is recommended
to install a new water line (see the “Tools and Parts” section at
the front of the guide for part details) and drain hose (supplied)
with the new dishwasher.
ELECTRICAL REQUIREMENTS
■ 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused
electrical supply
■ Copper wire only
■ A maximum of 2 field wiring supply conductors
(12 AWG largest size) plus 1 grounding conductor
are permitted in the terminal box.
We Recommend:
■ A time-delay fuse or circuit breaker
■ A separate circuit
■ If required, the air gap should be installed in accordance
with the air gap installation instructions. When you are
connecting the air gap, a rubber hose (not provided) will
be needed to connect to the waste tee or disposer inlet.
1
■ Use
/2" minimum I.D. drain line fittings.
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.
If Connecting Dishwasher with a Power Cord:
■ Use UL Listed power cord kit marked for
use with dishwasher. See the “Tools and
Parts” section at the front of the guide for
part details and orders.
■ Plug into a grounded 3 prong outlet. Outlet must
meet all local codes and ordinances.
If Connecting Dishwasher with Direct Wiring:
■ Use flexible, armored, or nonmetallic
sheathed copper wire with grounding
wire that meets the wiring requirements
for your home and local codes and ordinances.
■ Use a UL Listed/CSA Approved metallic strain relief.
See the “Tools and Parts” section at the front of the
guide for part details and orders.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
Page 1 of 2
W10806906-D-WH
11/16
Product and Cabinet Opening Dimensions
237/8"
(606 mm)
30"
(762 mm)
1
33
/2"
(851 mm)
min. with
wheels
removed
1
3
/2" - 41/2"
(88 mm - 106 mm)
For 4" (100 mm) toe kick, height of cabinet opening is 341/2" (863 mm).
241/2"
(622 mm)
B
3
/4"
(19 mm)
A
C
30"
(762 mm)
3
/4"
3
(94 mm)
21"
(533 mm)
A. Insulation may be compressed (not used on all models).
B. For panel-ready models, dishwasher depth is 24" (610 mm),
not including the 3/4" (19 mm) custom door panel.
C. Door handles may protrude forward of the face of the
dishwasher, varies by model.
34"
(864 mm)
D
(102 mm)
D. Measured from the lowest point on the underside
of the countertop. May be reduced to 331/2"
(851 mm) by removing the wheels and perforated
area of insulation (blanket) on dishwasher.
E. Minimum, measured from narrowest point
of opening
"
4
"
3
(76 mm)
24"
(620 mm)
(620 mm)
24"
E
(64 mm)
(64 mm)
3
1
/4"
(44 mm)
Check that all surfaces have no protrusions
that would prohibit dishwasher installation.
NOTE: Shaded areas
of cabinet walls
1
10
/2"
(267 mm)
3
6
/4"
show where utility
connections may
be installed.
(172 mm)
1
/4"
6
2
(159 mm)
"
1
1
/4"
2
/4"
2
(51 mm)
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
Page 2 of 2
W10806906-D-WH
11/16
Loading...