In an effort to conserve natural resources, this dishwasher includes a condensed User Guide. A complete User
Instructions can be downloaded at www.whirlpool.com/manuals.
For future reference, please make a note of your product model and serial numbers. You can find them on the label
located near the door on the right-hand or left-hand side of the dishwasher interior.
Model Number________________________________ Serial Number______________________________________
Register your dishwasher at www.whirlpool.com. In Canada, register your dishwasher at www.whirlpool.ca.
Para una version de estas instrucciones en español, visite www.whirlpool.com.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don’t immediately follow instructions.
DANGER
You can be killed or seriously injured if you don’t follow instructions.
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using the dishwasher, follow basic precautions, including the following:
■ Read all instructions before using the dishwasher.
■ Use the dishwasher only for its intended function.
■ Use only detergents or rinse agents recommended for use in a
dishwasher, and keep them out of the reach of children.
■ When loading items to be washed:
1) Locate sharp items so that they are not likely to damage the
door seal; and
2) Load sharp knives with the handles up to reduce the risk of
cut-type injuries.
■ Do not wash plastic items unless they are marked
“dishwasher safe” or the equivalent. For plastic items not so
marked, check the manufacturer's recommendations.
■ Do not touch the heating element during or immediately after
use.
■ Do not operate the dishwasher unless all enclosure panels are
properly in place.
SAVE THESE INSTRUCTIONS
■ Do not tamper with controls.
Do not abuse, sit on, or stand on the door, lid, or dish racks of
■
the dishwasher.
■ To reduce the risk of injury, do not allow children to play in or
on the dishwasher.
■ Under certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system
has not been used for such a period, before using the
dishwasher turn on all hot water faucets and let the water flow
from each for several minutes. This will release any
accumulated hydrogen gas. As the gas is flammable, do not
smoke or use an open flame during this time.
■ Remove the door or lid to the washing compartment
when removing an old dishwasher from service or
discarding it.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.
1
W10901523A
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
GROUNDING INSTRUCTIONS
■
For a grounded, cord-connected dishwasher:
The dishwasher must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for
electric current. The dishwasher is equipped with a cord
having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with all local
codes and ordinances.
WARNING:
Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
SAVE THESE INSTRUCTIONS
WARNING
Tip Over Hazard
Check with a qualified electrician or service representative if
you are in doubt whether the dishwasher is properly
grounded. Do not modify the plug provided with the
dishwasher; if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
■
For a permanently connected dishwasher:
The dishwasher must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the dishwasher.
KEY USAGE TIPS
Filtration system and maintenace
Your dishwasher has the latest
technology in dishwasher filtration.
This filtration system minimizes
sound and optimizes water and
energy conservation while providing
superior cleaning.
The filter system consists of two
parts, an upper filter assembly
and lower filter.
IMPORTANT: To avoid damage to dishwasher, do not operate your
dishwasher without filters properly installed. Be sure lower filter is
securely in place and upper filter assembly is locked into place. If
upper assembly turns freely, it is not locked into place.
The filters may need to be cleaned when:
■ Visible objects or soils are on upper
filter assembly.
■ Dishes feel gritty to the touch.
See “Filtration System” in the full User
Instructions for complete removal and
maintenance schedule.
IMPORTANT: Do not use a wire brush or
a scouring pad, etc., as they may damage
the filters.
Rinse filter under running water until soils are
removed. If you have hard to remove soils or
calcium deposits because of hard water, a soft
brush may be required.
Upper filter
assembly
Lower filter
L
O
C
K
P
U
S
H
D
O
W
N
&
T
U
U
R
N
N
L
O
C
K
Drying – Rinse aid is essential
You must use a drying agent such as a rinse
aid for good drying performance. Rinse aid
along with the Heat Dry option will provide
best drying and avoid excessive moisture in
dishwasher interior.
SLIDE
Energy efficiency
Energy efficiency is gained by extending cycle time and
reducing the amount of wattage and water used during
your dishwasher’s cycle. For exceptional cleaning, cycles
are longer due to the soak and pauses.
Efficient dishwashers run longer to save water and energy,
just as driving a car slower saves on gas. Your first cycle will
run longer to calibrate the optical water sensor.
Press Start every time you add a dish
IMPORTANT: If anyone opens the door, such as for
adding a dish (even during the Delay option), Start
must be pressed each time.
Push door firmly closed within 4 seconds of pressing
Start. If door is not closed within 4 seconds, the Start
button LED will flash, an audible tone will be heard, and
cycle will not start.
Internet connectivity (on some models)
Use the Internet Connectivity Guide included
in your literature pack to get connection and
operation instructions. You can also find these
and additional information at www.whirlpool.com/connect.
If you have any problems or questions, call the Whirlpool
Connected Appliance Team at 1-866-333-4591. In Canada,
visit www.whirlpool.ca/en_CA and click on the Whirlpool®
Connected Appliances link.
IMPORTANT: Remove leftover food, bones, toothpicks, and other hard
items from dishes. Remove labels from containers before washing.
■ Make sure when dishwasher door is closed, no items are blocking
detergent dispenser.
■ Items should be loaded with soiled surfaces facing down and
inward to the spray as shown in the graphics above. This will
improve cleaning and drying results. Angle dirtiest dish surface
downward, allowing space for water to flow up through rack and
between dishes.
■ Avoid overlapping items, like bowls or plates, that may trap food.
■ Place plastics, small plates, and glasses in upper rack.
■ Wash only items marked “dishwasher safe.”
■ To avoid thumping/clattering noises during operation, load dishes
so they do not touch one another. Make sure lightweight load
items are secured in racks.
■ Use slots in the covers and suggested loading patterns to keep
your silverware separated for optimum wash.
PUSH
2. Check that all arms spin freely
Items in the rack can block
the spray arms.
3. Add detergent
Premeasured Detergents
High-quality premeasured tablets
and packs are recommended for
improved performance.
Quality tablets and packs have been
proven better than powder, liquid, or gel
detergents at reducing filming on dishes.
Using tablets and packs over time will
start to reduce or eliminate white film.
They are suitable for all water hardness
and soil levels. Also, by using a rinse aid,
you can minimize repeat buildup of white
film (not all packs and tablets contain
rinse aid). Always place premeasured
detergents in main compartment and
close lid.
NOTE: Follow instructions on the package when using other
dishwasher detergent types. See the complete owners manual
for more details about powders, liquids, and gels.
■ Use automatic dishwasher detergent only. Add detergent just
before starting a cycle.
■ Fresh automatic dishwasher detergent results in better cleaning.
Store tightly closed detergent container in a cool, dry place.
To close lidTo open lid
SLIDE
NOTES:
■ The AnyWare™ Silverware Basket can sit in the door or on
the outside front of the lower rack for completely usable rack
space, letting you fit more items in the rack. It can also go in
your lower rack to fit your needs.
■ Silverware basket may vary by model.
■ If your silverware does not fit into the designated slots, lift and
slide covers off to remove them and mix silverware types to keep
them separated.
■ When loading silverware, always place sharp
items pointing down and avoid “nesting”
as shown.
SLIDE
SLIDE
Place selected detergent in
the dispenser. Place finger, as
Push OPEN, as shown,
and the lid will slide open.
shown, and slide lid closed.
Press firmly until it clicks.
4. Add rinse aid
■ Your dishwasher is designed to use rinse aid for good drying
performance. Without rinse aid, your dishes and dishwasher
interior will have excessive moisture. The heating and drying
options will not perform as well without rinse aid.
■ Rinse aid keeps water from forming droplets that can dry as spots
or streaks. It also improves drying by allowing water to drain off
of dishes after final rinse. Rinse aid does not adhere to dishware,
and when used, it is dispensed during each cycle.
3
■ To add rinse aid, open the dispenser
d
lid by gently pushing in the center of
the lid with your thumb while lifting up
on the edge.
■ Pour rinse aid into the opening until the indicator level shows
that it is full.
SLIDE
Pre Wash
OPEN
SLIDE
Full
Ad
6. Select options
You can customize your cycles by pressing the options desired. If you
change your mind, press the option again to turn off the option. Not
all options are available for every cycle. If an invalid option is selected
for a given cycle, the lights will flash. Adding options may increase the
cycle time.
7. Follow the progress of your dishwasher
The indicator LED on the front right corner
of the door panel will glow blue for washing/
rinsing, red for drying, and white for complete.
Some models indicate cycle progress with
LEDs on the control panel such as Add Dish,
Washing, Drying, Clean, and Sanitized.
■ Close dispenser by pushing down gently on the lid.
NOTE: For most water conditions, the factory setting will give
good results.
If you are experiencing poor drying performance, you may
want to try a higher setting. Turn the arrow adjuster to a
higher number to increase the amount of rinse aid.
5. Select a cycle
Efficient dishwashers run longer to save water and energy, just as
driving a car slower saves on gas. Typical cycle time is approximately
21/2 hours but can take less or more time to complete depending
on selections.
8. Start or resume a cycle
NOTE: If needed, run hot water at the sink nearest your dishwasher
until the water is hot. Turn off water.
Push door firmly closed within 4 seconds of pressing Start. If door
is not closed within 4 seconds, the Start button LED will flash, an
audible tone will be heard, and cycle will not start.
IMPORTANT: If the door is opened for any reason after the cycle
is started (even during the Delay option), the Start button must be
pressed again.
CYCLE GUIDE
This information covers several different models. Your dishwasher may not have all of the cycles and options described.
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the cycle for
the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle will automatically
compensate by adding time, heat, and water as needed.
CYCLESESTIMATED
This cycle senses the load size, soil amount, and toughness of soil, to adjust the
cycle for improved cleaning, using only the amount of water and energy needed.
The Sensor cycle is automatically selected if you first press the Start button.*
WASH TIME
W/O OPTIONS
2:10 to 3:153.38 to 7.4
WATER USAGE
GALLONS
(LITERS)
(12.8 to 28.0)
Use for hard-to-clean, heavily soiled pots, pans, casseroles, and regular tableware.2:45 to 3:257.4 (28.0)
This cycle is recommended for daily, regular, or typical use to completely wash
and dry a full load of normally soiled dishes. This dishwasher’s government energy
certifications were based on the Normal cycle with only the Heated Dry option
selected.**
For fast results, the 1-Hour Wash will clean dishes using slightly more water and
energy. For improved drying, select the Heat Dry option.
NOTE: Some detergents are not recommended for short wash cycles, please refer
to your detergent packaging for more information.
This cycle quietly soaks dishes with an extended prewash which eliminates the
need to presoak dishes, saving personal time and effort. For optimal cleaning results
during the Soak & Clean cycle, add prewash detergent. Use this cycle for loads with
heavy amounts of dried-on or hard to clean baked-on food.
This is a specialty cycle that you select from the Whirlpool® app and download
to your dishwasher. Your dishwasher remembers this cycle until you replace it by
downloading another cycle from the Whirlpool® app.
(on some models)
*The government energy certifications are not based on this cycle. See the Normal cycle description for the government energy certification
cycle. Using the Sensor cycle may increase your energy usage.
**No other washing and drying temperature options were selected, and it was not subject to truncated testing. Rinse aid was not used, and there
was no detergent used in the prewash.
2:00 to 3:102.4 to 7.4
(9.09 to 28.0)
0:55 to 1:057.87 (29.8)
6:45 to 7:257.4 (28.0)
VariableVariable up to
7.87 (29.8)
4
(varies by
model)
OPTIONSCAN BE
Delay displays how many hours before the cycle
will begin.
To delay the start:
1. Select a wash cycle and options.
2. Press DELAY. Each time you press Delay, it will
display the next available delay time.
3. Press START to begin the delay countdown.
NOTE: If the door is opened, such as to add a
dish, the Start button must be pressed to resume
the delay countdown.
Raises the main wash temperature to improve
cleaning for loads containing tough, baked-on food.
Dries dishes with heat. This option, with the use
of rinse aid, will provide the best drying results.
Plastic items are less likely to deform when loaded
in the top rack. Use Heat Dry for optimum drying
performance. For air dry, both Heat Dry and
Extended Dry LEDs are off.
Uses heat and additional time to dry dishes. For
the very best drying performance, use rinse aid
and the Extended Dry option.
Sanitizes dishes and glassware in accordance
with NSF International NSF/ANSI Standard 184
for Residential Dishwashers. Certified residential
dishwashers are not intended for licensed food
establishments. Only sanitizing cycles have been
designed to meet the requirements of the NSF/
ANSI 184 performance standard for soil removal
and for sanitization efficacy. There is no intention,
either directly or indirectly, that all cycles on a
NSF/ANSI 184 certified dishwasher meet the NSF/
ANSI 184 performance standard for soil removal
and for sanitization efficacy.
The Sani Rinse indicator glows at the end of the
cycle if the Sani Rinse option was successfully
completed. If the indicator does not activate, it is
probably due to the cycle being interrupted.
Use the Control Lock option to avoid unintended use of dishwasher between cycles, or cycle and option changes during a cycle.
To turn on Control Lock, press and hold CONTROL LOCK for 3 seconds. Control Lock light will stay on for a short time,
indicating that it is activated. When the Lock indicator is lit, all buttons are disabled. If you press any button while your
dishwasher is locked, the light flashes 3 times. The dishwasher door can still be opened/closed while the controls are locked.
To turn off Control Lock, press and hold CONTROL LOCK for 3 seconds. Control Lock light turns off.
SELECTED
WITH
Available
with any
cycle
Sensor
Heavy
Normal
Soak &
Clean
Sensor
Heavy
Normal
1-Hour
Wash
Soak &
Clean
Sensor
Heavy
Normal
1-Hour
Wash
Soak &
Clean
Sensor
Heavy
Normal
WHAT IT DOESADDED TIME
Delays start of a
cycle up to 24 hours
(on some models).
Raises the main
wash temperate
to135°F (57°C).
Uses a heating
element to speed
drying times. Heat
Dry option defaults to
On when any cycle is
selected, except for
1-Hour Wash.
Raises the main
wash temperate
to135°F (57°C)
and the final rinse
temperature to
(156°F (69°C).
TO CYCLE
0:05 to 0:130 – 3.9
0:05 to 1:060 – 3.9
ADDED WATER
GALLONS
(LITERS)
(0 – 14.6)
(0 – 14.6)
ControlPurposeComments
Press to start or resume
a wash cycle.
Press to cancel
wash cycle.
To follow progress of
your dishwasher cycle.
If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED
flashes. Cycle will not resume until Start is pressed and door is closed. Push door firmly closed
within 4 seconds of pressing Start.
Close the door firmly. Press and hold CANCEL-DRAIN for 3 seconds. The dishwasher starts a
2-minute drain (if needed). Let dishwasher drain completely.
The indicator LED on the front right corner of the door panel glows white when a cycle is finished.
If you select the Sani Rinse option, when the cycle is finished, the Sanitized indicator on the control
panel glows. If your dishwasher did not properly sanitize your dishes, the Sanitized indicator flashes
at the end of the cycle. This can happen if the cycle is interrupted or if water could not be heated to
required temperature. The light goes off when you open and close door or press CANCEL.
5
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.