AFTER SALES SERVICE ................................................................................28
3
SAFETY
RECOMMENDATIONS
IMPORTANT SAFETY INSTRUCTIONS
YOUR SAFETY AND SAFETY OF
OTHERS IS VERY IMPORTANT.
This manual and the appliance
itself provide important safety
warnings, to be read and
observed at all times.
This is the safety alert symbol.
This symbol alerts you to
potential hazards that can kill or
hurt you and others.
All safety messages will follow the
safety alert symbol and either the
word DANGER or WARNING.
These words mean:
Indicates a hazardous situation
which, if not avoided, will cause
serious injury.
Indicates a hazardous situation
which, if not avoided, could cause
serious injury.
All safety warnings give specic
details of the potential risk
presented and indicate how to
reduce risk of injury, damage and
electric shock resulting from
improper use of the appliance.
Carefully observe the following
instructions.
Failure to observe these
instructions may lead to risks.
The manufacturer cannot be held
liable for any damage resulting
from failure to respect this guide.
The Manufacturer declines any
liability for injury to persons or
animals or damage to property
if the above advice and
precautions are not respected.
Keep these instructions close at
hand for future reference.
Do not place or use gasoline or
other ammable materials in or
near the appliance: a re may
break out if the appliance is
inadvertently switched on.
Do not store explosive substances
such as aerosol cans.
When scrapping the appliance,
make it unusable by cutting o
the power cable and removing
the doors and shelves (if present)
so that children cannot easily
climb inside and become
trapped.
This appliance does not contain
CFCs. The refrigerant circuit
contains R134a (HFC) or R600a
(HC) (see the rating plate inside
the appliance).
Appliances with Isobutane
(R600a): isobutane is a natural gas
without environmental impact,
but is ammable. Therefore, make
sure the refrigerant circuit pipes
are not damaged. Keep special
attention in case of damaged
pipes emptying the refrigerant
circuit.
This product may contain
Fluorinated Greenhouse Gases
covered by the Kyoto Protocol;
the refrigerant gas is inside a
hermetically sealed system.
Refrigerant gas: R134a has a
Global Warming Potential of
(GW P) 130 0.
C-Pentane is used as blowing
agent in the insulation foam and
it is a ammable gas.
Do not damage the appliance
refrigerant circuit pipes.
Do not use mechanical, electric or
chemical means other than those
recommended by the
Manufacturer to speed up the
defrost process.
Do not use or place electrical
devices inside the appliance
compartments if they are not of
the type expressly authorised by
the Manufacturer.
Ice makers and or water
dispencers not directly connected
to the water supply must be lled
with potable water only.
4
EN
INTENDED USE
OF THE PRODUCT
This appliance is designed solely
for use as domestic usage. To aim
the appliance as professional use
is forbidden.
The manufacturer declines
allresponsibility for innapropiate
use or incorrect setting of the
controls.
The appliance is not intended to
be operated by means of an
external timer or separate remote
control system.
Do not use the appliance
outdoors.
The bulb used inside the
appliance is specically designed
for domestic appliances and is
not suitable for general room
lighting within the home (EC
Regulation 244/2009).
INSTALLATION
Only activate the appliance when
the installation procedure has
been completed.
Installation and repairs must be
carried out by a qualied
technician, in compliance with
the manufacturer’s instructions
and local safety regulations. Do
not repair or replace any part of
the appliance unless specically
stated in the user manual.
Use protective gloves to perform
all unpacking and installation
operations.
The appliance must be
disconnected from the power
supply before carrying out any
installation operation.
After unpacking the appliance,
make sure that it has not been
damaged during transport. In the
event of problems, contact the
dealer or your nearest After-sales
Service.
During installation, make sure the
appliance does not damage the
power cable.
The appliance must be handled
and installed by two or more
persons.
When installing the appliance
make sure that the four feet are
stable and resting on the oor,
adjusting them as required, and
check that the appliance is
perfectly level using a spirit level.
Remove the bottom protection
by tilting and turning the washing
machine on one rear bottom
corner. Make sure that the plastic
part of the bottom protection (if
available on the model) remains
in the packing and not in the
machine bottom. This is
important, as otherwise the
plastic part could damage the
washing machine during
operation.
Wait at least two hours before
switching the appliance on, to
ensure that the refrigerant circuit
is fully ecient.
Make sure the appliance is not
near a heat source.
ELECTRICAL WARNINGS
Make sure the voltage specied
on the rating plate corresponds
to that of your home.
The power supply ranges are
indicated on the rating plate.
Regulation require that the
appliance is earthed.
For installation to comply with
current safety regulations, an
omnipolar switch with minimum
contact gap of 3mm is required.
If the power cable is damaged it
must be replaced with an
identical one. The power cable
must only be replaced by a
qualied technician in compliance
with the manufacturer instruction
and current safety regulations.
Contact an authorized service
center.
The electrical components must
not be accessible to the user after
installation.
The power cable must be long
enough for connecting the
appliance, once tted in its
housing, to the main power
supply.
Do not use extension leads.
Do not pull the power supply
cable.
Do not use multiple plug
adaptors if the appliance is tted
with a plug.
For appliances with tted plug, if
the plug is not suitable for you
socket outlet, contact a qualied
technician.
Do not touch the appliance with
any wet part of the body and do
not operate it when barefoot.
Do not operate this appliance if it
has a damaged mains cord or
plug, if it is not working properly,
or if it has been damaged or
dropped. Do not immerse the
mains cord or plug in water. Keep
the cord away from hot surfaces.
When using a residual current
circuit breaker (RCCB), only use a
model marked with .
5
The appliance is arranged for
operation in places where the
temperature comes within the
following ranges, according to
the climatic class given on the
rating plate.
The appliance may not work
properly if it is left for a long time
at a temperature outside the
specied range.
Climatic Class Amb. T. (°C)
SN From 10 to 32
N From 16 to 32
ST From 16 to 38
T From 16 to 43
ELECTRICAL CONNECTION FOR
GREAT BRITAIN AND IRELAND
ONLY
Fuse replacement.
If the mains lead of this appliance
is tted with a BS 1363A 13amp
fused plug, to change a fuse in
this type of plug use an A.S.T.A.
approved fuse to BS 1362 type
and proceed as follows:
1. Remove the fuse cover (A) and
fuse(B).
2. Fit replacement 13A fuse into
fuse cover.
3. Ret both into plug.
Important:
The fuse cover must be retted
when changing a fuse and if the
fuse cover is lost the plug must
not be used until a correct
replacement is tted.
Correct replacement are
identied by the colour insert or
the colour embossed in words on
the base of the plug.
Replacement fuse covers are
available from your local electrical
store.
For the Republic of Ireland only
The information given in respect
of Great Britain will frequently
apply, but a third type of plug
and socket is also used, the 2-pin,
side earth type.
Socket outlet / plug (valid for
both countries)
If the tted plug is not suitable for
your socket outlet, please contact
After-sales Service for further
instruction. Please do not attempt
to change plug yourself. This
procedure needs to be carried
out by a qualied technician in
compliance with the
manufactures instructions and
current standard safety
regulations.
CORRECT USE
Do not swallow the contents
(non-toxic) of the ice packs (in
some models).
Do not eat ice cubes or ice lollies
immediately after taking them
out of the freezer since they may
cause cold burns.
For products designed to use an
air lter inside an accessible fan
cover, the lter shall be always in
position when the refrigerator is
in function.
Do not store glass containers with
liquids in the freezer
compartment since they may
break.
Do not obstruct the fan (if
available) with food items.
After placing the food check if the
door of compartments closes
properly, especially the freezer
door.
Damaged gasket must be
replaced as soon as possible.
CHILDREN SAFETY
Very young (0-3 years) and young
children (3-8 years) shall be kept
away unless continuously
supervised.
Childern from 8 years old and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge can use this
appliance only if they are
supervised or have been given
instructions on safe appliance use
and if they understand the
hazards involved. Children shall
not play with the appliance.
Cleaning and user maintenance
shall not be made by childern
without supervision.
Keep the packaging materials
(plastic bags, polystyrene parts,
etc.) out of reach of children.
CLEANING AND MAINTENANCE
The appliance must be
disconnected from the power
supply before carrying out any
cleaning or maintenance
operation.
Never use steam cleaning
equipment
6
SAFEGUARDING
THE ENVIRONMENT
EN
DISPOSAL OF PACKAGING
MATERIALS
The packaging material is 100%
recyclable and is marked with the
recycle symbol:
The various parts of the
packaging must therefore be
disposed of responsibly and in
full compliance with local
authority regulations governing
waste disposal.
SCRAPPING OF HOUSEHOLD
APPLIANCES
This appliance is manufactured
with recyclable or reusable
materials. Dispose of it in
accordance with local waste
disposal regulations.
For further information on the
treatment, recovery and recycling
of household electrical
appliances, contact your
competent local authority, the
collection service for household
waste or the store where you
purchase the appliance.
This appliance is marked in
compliance with European
Directive 2002/96/EC, Waste
Electrical and Electronic
Equipment (WEEE).
By ensuring this product is
disposed of correctly, you will
help prevent potential negative
consequences for the
environment and human health,
which could otherwise be caused
by inappropriate waste handling
of this product.
This symbol on the product
or on the accompanying
documentation indicates
that it should not be treated as
domestic waste but must be
taken to an appropriate collection
centre for the recycling of
electrical and electronic
equipment.
ENERGY SAVING TIPS
Install the appliance in a dry, well
ventilated room far away from
any heat source (e.g. radiator,
cooker, etc.) and in a place not
exposed directly to the sun. If
required, use an insulating plate.
To guarantee adequate
ventilation follow installation
instructions. Insucient
ventilation on back of the
product increases energy
consumption and decreases
cooling eciency.
The internal temperatures of the
appliance may be aected by the
ambient temperature, frequency
of door opening, as well as
location of the appliance.
Temperature setting should take
into consideration these factors.
Reduce to a minimum door
opening
When thawing frozen food, place
them in the refrigerator. The low
temperature of the frozen
products cools the food in the
refrigerator.
Allow warm food and drinks to
cool down before placing in the
appliance.
Positioning of the shelves in the
refrigerator has no impact on the
ecient usage of energy. Food
should be placed on the shelves
in such way to ensure proper air
circulation (food should not touch
each other and distance between
food and rear wall should be
kept).
You can increase storage capacity
of frozen food by removing
baskets and, if present, Stop Frost
shelve, maintaining an equivalent
energy consumption.
High energy class products are
tted with high eciency motors
that remain operational for
longer, but have a low power
consumption. Do not worry if the
engine continues to run for
longer periods.
7
DECLARATION
OF CONFORMITY
This appliance has been designed
for preserving food and is
manufactured in compliance with
Regulation (CE) No. 1935/2004.
This appliance has been
designed, manufactured and
marketed in compliance with:
› safety objectives of the “Low
Voltage” Directive 2006/95/CE
(which replaces 73/23/ CEE and
subsequent amendments);
› the protection requirements of
Directive “EMC” 2004/108/
EC. Electrical safety of the
appliance can only be guaranteed
if it is correctly connected to an
approved earthing system.
8
PRODUCT
DESCRIPTION
APPLIANCE
1.
2.
3.
10.
11.
14.
15.
16.
17.
4.
5.
6.
7.
8.
9.
13.
12.
19.
18.
EN
1. Lighting
2. Fan
3. Area Shelves
4. Multi-Flow Cold Air System
5. Bottle Rack
6. Active Zero Display
7. Active Zero Drawer
8. Rating Plate / Commercial Name
9. Fruits And Vegetables Crisper
10. Crisper Divider
11. Door Reversibility Kit
12. Bottle Holder
13. Door Trays
14. Storage Baskets For Frozen
Food Items
15. Shelves
16. Middle Basket (Freezing Zone)
17. Ice Tray And/Or Cold
Accumulator
18. Door Seals
19. Control Panel
CONTROL PANEL
2.
3.4.
1.
Fast Cool press 3 sec.
Fridge
press 3 sec.
6.7.8.9.10.
Freezer
Fast Freeze press 3 sec.
Note: Unless otherwise specied
the appliance accessories are not
dishwasher safe.
1. Fridge Temperature Leds
2. On/Stand-By Icon/Button
3. 6Th Sense Fresh Control Icon
4. Eco Night Icon/Button
5. Freezer Temperature Leds
6. Fridge Temperature / Fast Cool
5.
(Press 3 Sec.) Button
7. Black Out Icon
8. Stop Alarm Button / Alarm Icon
9. Key Lock Button
10. Freezer Temperature / Fast
Freeze (Press 3 Sec.) Button
Note: Buttons and control panel
display must not be cleaned with
alcohol or alcohol-derived
substances, but with a dry cloth.
9
TECHNICAL
DATA
PRODUCT DIMENSIONS
Height 2000mm
Width595mm
Depth660mm
NET VOLUME FRIDGE L 247L
NET VOLUME FREEZER L 97L
DEFROST SYSTEM
FridgeAutomatic
FreezerSemi-Automatic
RISING TIME H12h
FREEZING CAPACITY KG/24H12Kg/24h
ENERGY CONSUMPTION KWH/24H0,69Kwh/24h
NOISE LEVEL DBA42dba
ENERGY CLASSA++
DOOR
DOOR REVERSIBILITY Note: The direction of door opening can be
changed. If this operation is performed by Aftersales Service it is not covered by the warranty.
Is recommended to reverse door swing by two
persons.
Follow instruction in Installation Guide.
REFRIGERATOR
LIGHT
The light system inside the refrigerator
compartment uses LEDs light, allowing a better
lightning as well as a very low energy consumption.
If the LED light system does not work, please
contact the Service to replace it.
Note: The refrigerator compartment light switches
on when the refrigerator door is opened. If the door
is kept open for more then 8 minutes the light will
be automatically switched o.
SHELVES
All shelves, aps and pull-out baskets are
removable.
10
ACTIVE ZERO
DRAWER
EN
The Active Zero compartment is specically
designed to maintain a low temperature and the
correct humidity to preserve fresh food for longer
TURNING ON AND TURNING OFF
THE COMPARTMENT
The internal temperature of the compartment is
approximately 0° when the compartment is turned
on.
For the correct functioning of the Active Zero
compartment, it is necessary that:
› the refrigerator compartment is turned on;
› the temperature is between +2°C and +6°C
› the drawer in the Active Zero compartment must
be inserted for it to be turned on;
› one of the following special functions is not
selected: Stand-by, Cooling-O, Vacation (if
present), in this case, remove the food contained in
it.
Important
If the compartment is turned on and food with a
high water content is present, condensation may
form on the shelves. In this case, turn the function
o temporarily.
Be careful when positioning food and containers
that are small in size on the upper shelf of the Active
Zero compartment in order to prevent them
accidentally falling between the shelf and the back
wall of the refrigerator compartment.
(for example, meat, sh, fruits and winter
vegetables).
To activate/
deactivate the
box, press the
button.
When the box has been activated, the symbol lights
up.
Note:
› if the symbol does not light up when you turn on
the compartment, check that the drawer is properly
inserted; if the problem persists contact the
authorised Technical Assistance Service.
› if the compartment is turned on and the drawer is
open, the symbol in the control panel may
automatically turn o. The symbol will light up
again when the drawer is inserted
› regardless of the state of the compartment, you
may hear a faint noise, which you should consider as
normal
› when the compartment is not in operation, the
temperature inside it depends on the general
temperature of the refrigerator compartment. In
this case, it is advised that fruits and vegetables that
are not sensitive to cold (berries, apples, apricots,
carrots, spinach, lettuce, etc.) are stored in it.
REMOVING THE ACTIVE ZERO COMPARTMENT
Carry out the following steps:
› to make it easier to remove the compartment, we
recommend that you empty (and possibly remove)
the lower door shelves;
› turn o the compartment;
› remove the compartment by rotating it upwards;
› remove the white plastic shelf under the
compartment.
Note
It’s not possible to remove the upper shelf and side
supports.
To use the Active Zero compartment again, carefully
reposition the white plastic shelf under the
compartment before inserting the drawer and
turning the function back on.
To have a larger refrigerator volume and to reduce
energy consumption, it is recommended that you
turn o and remove the Active Zero compartment.
11
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.