Whirlpool WA 2362 INSTRUCTION FOR USE

WA 2362

PROGRAMME TABLE

is a registered trademark

Indicator: Door lock Indicator: Water tap

Programme Care label Type of fabric /

Cotton / Cotton Coloured

Easy care

Delicates

Wool

Rinse + Spin

Gentle Spin

Draining

Degree of soiling

Lightly to averagely soiled bed linen, table linen, underwear, towels, shirts etc. (linen and cotton) etc.

Lightly to averagely soiled blouses, shirts, etc. made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or blends with cotton.

Curtains, delicate dresses, skirts, shirts and blouses.

Only machine washable woollens with pure new wool label.

—

Max. Load Detergent

kg °C

Normal 6.2

Rapid 3.0

Normal 2.5

Rapid 1.5

1.5

1.0

6.2

—

and Additives

Softener Main

❉

————————

—————————— —

Pre-

Wash

wash

yes

❉❉❉❉❉❉❉

❉

————

——

Half

Short Intensive

Load

———

❉

Options =

Rinse

——

❉

Rinse

Pre-

Wash

—

Spinning

❉

Hold

❉❉❉

❉

Indicator:

Wash Rinse Spin

Thermostat

knob

From “ ” to 95 Short: From

“ ” to 60

From “ ” to 60

Short: From “ ” to 60

From “ ” to 40

“”

——

Programme

Selector

Programme Duration

approx.

Min.

120

85 45

—

If “Short” is selected the options “Intensive Rinse” and “Prewash” are inhibited.

—

If you select the special option “Rinse Hold” don’t leave garments to soak for too long.

Programme for treating wash with starch or softener. Terminates with an intensive spin cycle, same as the spin cycle in the Cotton Coloured programme.

Programme for gentle spin cycle, same as the spin cycle in the Wool programme.

Drain only without spin cycle. Alternative way of terminating programmes with “Rinse hold” setting.

Notes

1) Appliances with max. spin speed greater than 900 rpm: for improved garment care, spin speed is restricted to 900 rpm.

2) The programme duration figures are approximate values for a programme with maximum temperature but without special options.

2B 5019 100 03864

Power and water consumption data

Programme

Cotton / Cotton Coloured 95 5.0 — 60 1.80 120

Cotton / Cotton Coloured 60 5.0 — 55 1.20 115

Cotton / Cotton Coloured 60 2.5 Saving half load 40 0.90 100

Cotton / Cotton Coloured 40 5.0 — 55 0.60 100

Cotton / Cotton Coloured 30 3.0 Short 35 0.30 55

Easy care 60 2.5 — 60 0.90 85

Easy care 40 2.5 — 54 0.40 70

Easy care 30 1.5 Short 25 0.20 35

Delicate 40 1.5 — 60 0.50 40

Wool 40 1.0 — 60 0.50 35

Prewash cycle increases programme duration by approx. 15 minutes. Consumption data were measured in normali sed conditions in compliance with Standard IEC 60 456.

Consumption data in the home may v ary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

Thermostat

knob

(°C) (kg) (l) (kWh) (min.)

Maximum

load

Special options Water Electricity

Programme

duration

ROUTINE WASHES:

1. Turn on the tap.

2. Sort the laundry according to fabric type and colour and load the machine.

3. Close the door.

4. Pour in detergent and additives.

5. Select the programme, the temperature and any special options you require.

6. Hold down the “Start” button for about one second.

NOTE:

During the first 15 minutes of Cotton and Easy Care programmes (each without Prewash) you can open the door to add items to the wash. This is not possible when the special function “Short” is selected.

TO INTERRUPT THE PROGRAMME:

To interrupt a programme that is already running and then continue later:

1. Set the programme selector knob to “0”.

2. After the required break, reselect the programme.

3. Hold down the “Start” button for about one second. The programme will continue from where it was interrupted.

CHANGING PROGRAMME DURING A RUNNING PROGRAMME:

a) TO SELECT A NEW PROGRAMME OR A DIFFERENT TEMPERATURE AND

CONTINUE

1. Select a new programme and/or new temperature.

2. Hold down the “Start” button for about one second. The new programme will continue from the same programme step where the running programme was interrupted.

b) TO CANCEL A PROGRAMME THAT IS ALREADY RUNNING AND START A

DIFFERENT PROGRAMME FROM THE BEGINNING There’s no need to add more detergent when you start the new programme, because the appliance drains only just few water when you cancel the current programme.

1. Hold down the “Start” button for five seconds, or until the programme control audibly restarts.

2. Wait until the programme sequence indicator returns to its initial position on the left (no longer visible).

3. Set the programme selector to “0”.

4. Set the programme selector knob to the new programme, select the temperature (if different) and any different special options you require.

5. Hold down the “Start” button for about one second.

TROUBLE-SHOOTING GUIDE:

The appliance is equipped with safety functions able to identify and indicate the presence of faults and react appropriately. Most faults are minor problems that can be solved quickly. The following list gives several examples:

• The appliance fails to start.

• The appliance stops in mid programme.

• No water or insufficient water supply.

• The appliance does not drain.

• The machine vibrates during the spin cycle.

• Final spin results are poor.

• Detergent and additive product residues in the detergent dispenser at end of wash.

The cause and action notes for the above points are given in the instruction for use in the chapter “Trouble-shooting guide”.