ASSISTANCE OU SERVICE ..............Couverture arrière
W10330946A
W10331731A-SP
WASHER SAFETY
1
2
WHAT’S NEW ABOUT YOUR LOAD-SENSING WASHER
Load-Sensing determines the appropriate amount of water for each load based on your cycle and options selected for maximum
energy and water savings.
Although your new load-sensing washer may look the same as other washers, there are a few important steps that are required to
maximize your water and energy savings:
BEFORE STARTING THE WASHER:
Presort all of your laundry.
Add all of your garments and laundry products to the
washer and washer dispensers. See “Starting Your Washer”.
Do not interrupt the cycle or open the lid after starting
the washer. Opening the lid will reduce or eliminate water
savings. If the lid is opened during ll, the washer will add
more water to accommodate any additional load. If the
lid is opened after the washer has completed lling, the
washer will then ll to the highest level.
The following describes what to expect when using a washer with load-sensing technology.
After starting your washer, there will be a
short pause before the washer begins to
ll. The washer makes different sounds
and pauses briey throughout each cycle.
This is normal.
Dry Load
How It Works
Next, three nozzles spray to evenly
saturate the load. Then a sensing step
occurs. The lling stops, and the agitator
moves the load for a very brief time.
Load Filling/Sensing
The washer estimates how much more
water to add; then, lling resumes and
continues to sense until the right amount
of water is reached. Now washing begins.
Correct Water Level for Load
Water may not cover the top of the clothes and water level will
vary with size of load. This is normal for Auto Load-Sensing
washers. For these models, the water ll is optimized by the
system for best wash performance.
IMPORTANT: To save water and energy, DO NOT OPEN THE LID
after starting the washer.
3
CONTROL PANEL AND FEATURES
12
1
Temperature Control
Temperature Control senses and maintains uniform
water temperatures by regulating incoming hot and
cold water.
Warm and hot water will be cooler than what your
previous washer provided.
Even in Cool wash, some warm water is let into the
washer to maintain a minimum temperature.
Select a wash temperature based on the type of fabric
and soils being washed. For best results follow the garment
label instructions, using the warmest wash water safe for
your fabric.
Wash Temp
Hot
Some cold water is added to
save energy. This will be cooler
than your hot water heater
setting.
Warm
Some cold water will be
added, so this will be cooler
than what your previous washer
provided.
Cool - brights/darks
Warm water is added to assist
in soil removal and to help
dissolve detergents.
Cold
Warm water is added to assist
in soil removal and to help
dissolve detergents.
Tap Cold
This is the temperature from
your faucet.
Suggested Fabrics
Whites and pastels
Durable garments
Heavy soils
Bright colors
Moderate to light
soils
Colors that bleed
or fade
Light soils
Dark colors that
bleed or fade
Light soils
Dark colors that
bleed or fade
Light soils
3
45
2
Extra Rinse
If you desire an extra rinse at the end of your regular cycle,
turn the Extra Rinse knob to ON.
On models without the Extra Rinse knob, choose a second
rinse by pushing the Cycle Control knob in and rotating it to
any of the “Rinse” cycle settings.
3
Fabric Softener
Use this option if you are using liquid fabric softener in the
dispenser. This option ensures that the softener is properly
distributed in the rinse cycle.
4
Fabric Select
Choose the appropriate Fabric Select setting for the type
of garments you are washing. Each setting has a speed
designed for different fabrics and soil levels. See “Cycle
Guide” for more information.
5
Cycle Control knob
Select the wash cycle best suited for your type of fabric.
See “Cycle Guide” for more details.
NOTE: In wash water temperatures colder than 60° F (15.6° C),
detergents do not dissolve well and soils can be difcult to
remove.
4
CYCLE GUIDE
Types of Fabric
Cottons, linens,
synthetic fabrics
Sturdy fabrics,
Colorfast items
Pillows, sleeping
bags, comforters,
jackets
Machine wash silks
and hand wash
fabrics
Washable knits,
machine wash
silks
Soil
Level
Normal
Heavy
Medium
Light
Light
Fabric
Select
Normal
Heavy Duty
Bulky Items/
Comforters
Hand Wash
Delicate
Spin Speed
High/High
High/High
High/High
Intermittent
Low/Low
Low/Low
CycleAgitation /
Heavy
Regular
Super
Wash
Heavy
Regular
Heavy
Light
Light
Wash
Time*
10-14
14-16
10-14
6
6
Cycle Details:
Use this cycle for normally soiled
cottons and mixed fabric loads
Use this cycle for heavily soiled cottons
or sturdy fabrics.
This cycle thoroughly soaks and saturates
large and nonabsorbent items. Add the
load evenly around the basket wall in loose
heaps.
Use for special care items. Brief low-speed
agitations/ spins and short soaks provide
the gentlest cleaning while minimizing
wrinkling.
Use for special care items. Brief lowspeed agitations and short soaks provide
the gentlest cleaning. Low-speed spin
minimizes wrinkling.
Work shirts and
pants and synthetic
fabrics
* Approximate time in minutes
Light/
Medium
Casual/Perm
ADDITIONAL CYCLES
Adds a second rinse.
Select prior to starting washer
to automatically add to wash
cycle, eliminating need to
return later to select
a second rinse.
Extra Rinse
This cycle can be used for
washing 2-3 lightly soiled
items that are needed quickly.
Agitation and spin speeds will
vary by the fabric selections.
Press
Quick Wash
High/Low
Regular
Light
This cycle provides agitation
and unlimited soak time
required to remove stains.
Option 1 - To use same water
for wash cycle: advance Cycle
Select knob to a wash cycle.
Add laundry products and
start a new wash cycle as
normal.
Option 2 - Drain existing
water: advance Cycle Select
knob to a spin setting. Add
laundry products and start a
new wash cycle as normal.
6-10
Soak
Use this cycle to wash no-iron fabrics and
blends. Provides low speed/spin speeds to
minimize wrinkling.
This cycle helps to remove
heavy soils requiring
pretreatment. Prewash
does not include a rinse
cycle; proceed to setting
Fabric Select and Cycle
Select knobs and add
laundry products as
normal.
Prewash
5
STARTING YOUR WASHER
WASHER USE
BEFORE STARTING THE WASHER:
Add all items and laundry products to the washer before pulling
the Cycle Control knob out to achieve full water and energy
savings. Opening the lid will reduce or eliminate water savings.
IMPORTANT: When washing any article of clothing, always
follow fabric care labels and manufacturer’s directions.
1. Measure detergent and add to the bottom of the washer. If
desired, add oxi or color-safe bleach products to the bottom
of the washer as well.
2. Loosely add sorted load of clothes
to wash basket.
Load evenly to maintain washer
balance.
Mix large and small items.
Use garment bags for smaller items.
Do not wrap large items such as sheets
around the agitator. Items need to move
freely for best cleaning and to reduce
wrinkling and tangling.
3. Add only liquid chlorine bleach to the dispenser. Bleach
is immediately added into the washer and is diluted
automatically during the wash cycle.
Using a cup with a pouring spout, measure amount of
bleach. Do not allow bleach to spill, splash, drip, or run
into the basket or on load. Do not use more than the
recommended amount.
NOTE: Undiluted bleach will damage any fabric it touches.
Damage may appear several washings later as rips, tears, holes,
and color loss.
4. Add liquid fabric softener to dispenser.
Fabric softener is added automatically
during the nal rinse cycle. Turn the
Fabric Softener knob to the softener
Added position.
Measure recommended amount of liquid fabric softener.
Do not allow liquid fabric softener to spill, splash, drip,
or run into the basket or on load. Do not use more than
the recommended amount.
Always dilute liquid fabric softener by lling the dispenser
with warm water until reaching the Max Fill Line arrows.
Undiluted fabric softener can stain fabrics.
NOTE: Do not use this dispenser to add powdered chlorine or
color-safe bleach to your load.
6
5. Close the washer lid. Washer will not operate with lid open.
6. Select Temperature and Fabric Select Option
7. Select Extra Rinse Option, if desired
8. Select Cycle
Push the Cycle Control knob in and turn clockwise to the
cycle you want.
Water Inlet Hoses
This washer does not include water inlet hoses. Whirlpool
Corporation recommends use of factory specied parts. See
“Accessories” for a list of factory specied hoses available for
separate purchase. These hoses are manufactured and tested to
meet Whirlpool Corporation’s specications.
Replace inlet hoses after 5 years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker.
Moving and Storage
Because some water may stay in the hoses, freezing can
damage your washer. If storing or moving your washer during
freezing weather, winterize it.
Winterizing your washer
1. Shut off both water faucets. Disconnect and drain water inlet
hoses. Pour 1 qt (1 L) of R.V.-type antifreeze into the basket.
2. Run washer on a drain and spin setting for about 30 seconds
to mix the antifreeze and remaining water.
3. Unplug washer or disconnect power.
9. Start the washer by pulling out the Cycle control knob.
NOTE: For best water savings, avoid stopping the washer.
However, if the washer does need to be stopped:
To stop at any time, push in the Cycle Control knob.
To restart, close the lid and pull out the Cycle Control
knob.
WASHER CARE
Cleaning Your Washer
Use a soft, damp cloth or sponge to wipe up any spills such as
detergent or bleach from the outside of your washer.
Clean your washer interior by mixing 1 cup (250 mL) of chlorine
bleach and enough detergent to equal twice the manufacturer’s
recommended amount for a normal wash load. Pour this mixture
into your washer and run it through a complete cycle using hot
water. Repeat this process if necessary.
Remove any hard water deposits using only cleaners labeled as
washer safe.
Cleaning the liquid fabric softener dispenser
1. Remove dispenser by grasping top with both hands and
squeezing, while pushing upward with thumbs.
2. Rinse dispenser under warm water, then replace it.
NOTE: To avoid damage to the washer or clothing, do not wash
clothes with the liquid fabric softener dispenser removed.
To use washer again
1. Flush water pipes and hoses. Reconnect water inlet hoses.
Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run the washer through a complete bulky items cycle with
1 cup (250 mL) of detergent to clean out antifreeze.
Storage, non-use, or vacation care
Operate your washer only when you are at home. If you will be
on vacation or not using your washer for an extended period of
time, you should:
1. Unplug washer or disconnect power.
2. Turn off the water supply to the washer. This helps avoid
ooding (due to a water pressure surge) while you are away.
7
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently
Asked Questions) to possibly avoid the cost of a service call.
In U.S.A. www.whirlpool.com/help
Noisy
Is the load balanced and the washer level? The wash load
should be balanced and not tightly packed. The washer must
be level. The front feet should be properly installed and the
jam nuts tightened. Reset the rear leveling legs (if needed).
See “Installation Instructions.”
Did you completely remove the yellow shipping strap
with shipping pins? See “Installation Instructions.”
Are the gears engaging after the drain and before spin, or
is the upper part of agitator clicking during wash? These
are normal washer noises.
Leaking
Check the following:
Are the ll hoses tight?
Are the ll hose washers properly seated?
Is the drain hose installed? See “Installation Instructions.”
Is the sink or drain clogged? Sink and standpipe must be
able to handle 17 gal. (64 L.) of water per minute.
Is water deecting off the tub ring or the load? Center
the tub before starting the washer. The wash load should
be balanced and not tightly packed. The ll or spray rinses
can bounce off the load. The washer must be level. The front
feet should be properly installed and the jam nuts tightened.
Reset the rear leveling legs (if needed). See “Installation
Instructions.”
Check household plumbing for leaks.
Dispensers clogged or bleach leaking
Did you follow the manufacturer’s directions when adding
fabric softener to the dispenser? Measure detergent and
fabric softener. Slowly pour into the dispensers. Wipe up all
spills. Dilute fabric softener in the fabric softener dispenser.
Periodically clean the dispensers.
Did you put powdered color-safe bleach into the liquid
chlorine bleach dispenser? Add powdered color-safe
bleach directly to the basket.
Water level seems too low
Auto load sensing may use less water than you would
expect. This is normal and provides good fabric care.
Does the water level seem too low, or does the washer
appear to not ll completely? The top of the agitator is
much higher than the highest water level. This is normal and
necessary for clothes to move freely.
Water level seems too high
Did you open the lid or stop the washer while the washer
was lling to begin the wash? This will interrupt the sensing
feature and cause the washer to stop lling. Closing the lid
will resume ll, but the washer will add additional water to
compensate for any additional load items that might have
been added to the basket.
Did you open the lid after washing started or during the
rinse? The washer will ll to the highest water level once the
lid is closed.
Washer won’t run, ll, rinse, or agitate; washer stops
Is the power cord plugged into a grounded 3 prong
outlet? Plug power cord into a grounded 3 prong outlet.
Are you using an extension cord? Do not use an extension
cord.
Is the indicator on the Timer knob properly lined up with
a cycle? Turn the Timer knob to the right slightly and pull
knob out to start.
Are the water inlet valve screens clogged? Turn off the
water and remove inlet hoses from the washer. Remove any
accumulated lm or particles. Reinstall hoses, turn on water,
and check for leaks.
Are both the hot and cold water faucets turned on?
Turn on the water.
Is the water inlet hose kinked? Straighten the hoses.
8
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.