Whirlpool W10372117, W10324365, W10372116, W10324363 Instruction Sheet

HIGH ALTITUDE KIT INSTALLATION INSTRUCTIONS
For use to convert cooking appliance for elevations above 6,560 ft. (1999.5 m)
Kit Number W10324365 - Natural Gas (NG) High Altitude Kit Contains:
3 - Jet: NG, C-size single burner, high altitude
2 - Main jet: NG, D-size dual burner, high altitude
Hood griddle: NG, high altitude
Spud: high altitude main oven bake, NG
Spud: high altitude small oven bake, NG
Kit: BYPASS high altitude, NG Number W10160841
Instruction sheet
Kit Number W10324363 - Propane Gas (LP) High Altitude Kit Contains:
3 - Jet: LP, C-size single burner, high altitude
2 - Main Jet: LP, D-size dual burner - high altitude
Hood griddle: LP, high altitude
Spud: high altitude main oven bake, LP
Spud: high altitude main oven broil, LP
Spud: high altitude small oven bake, LP
Kit: BYPASS High Altitude, LP Number W10237848
Instruction Sheet
GAS CONVERSION SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
follow instructions.
can be killed or seriously injured if you don't
You instructions.
follow
W10352797A
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions. If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell. Gas suppliers recommend that you use a gas detector approved by UL or CSA. For more information, contact your gas supplier. If a gas leak is detected, follow the “What to do if you smell gas” instructions.
In the State of Massachusetts, the following installation instructions apply:
Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
If using a ball valve, it shall be a T-handle type.
A flexible gas connector, when used, must not exceed 3 feet.
2
GAS CONVERSIONS
C
IMPORTANT: Gas conversions must be done by a qualified installer. Before proceeding with the conversion, shut off the gas supply to the range prior to disconnecting the electrical power.
WARNING
This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer's instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper and complete until the operation of the converted appliance is checked as specified in the manufacturer's instructions supplied with this kit.
WARNING
Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water column.
Examples of a qualified person include: licensed heating personnel,
authorized gas company personnel, and authorized service personnel.
Failure to do so can result in death, explosion, or fire.
LP Gas Conversion
1. Turn the manual shutoff valve to the closed position.
B
A
A. To range B. Shutoff valve (closed position) C. Gas supply line
2. Unplug range or disconnect power.
To Convert Gas Pressure Regulator
1. Remove screws from kick plate.
B
A
A. Kick plate B. Remove these screws.
2. Push up on kick plate to release plate from shoulder screws.
3. Gently lay kick plate aside to avoid scratching the stainless
steel.
4. Locate the gas pressure regulator at the left rear of the range.
A
A. Gas pressure regulator
3
5. Remove the gas pressure regulator cap by using a large flat-
blade screwdriver, turning the regulator cap counterclockwise.
NOTE: Do not remove the spring beneath the cap.
6. Turn over the gas pressure regulator cap and reinstall on the
regulator: For Natural gas to LP, the hollow end faces outward and the letters “LP” are visible. For LP to Natural gas, the hollow end faces inward and the letters “NAT” are visible.
Gas Supply Pressure Testing
Gas supply pressure for testing regulator must be at least 1" water column pressure above the manifold pressure shown on the model/serial rating plate.
Line pressure testing above ½ psi gauge (14" WCP)
The range and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa).
Line pressure testing at ½ psi gauge (14" WCP) or lower
The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa).
To Convert Oven Bake Burner (30" [76.2 cm] and 36" [91.4 cm] models and the Right Oven Cavity on 48" [121.9 cm] models)
1. Remove oven racks and the extendable roller rack from
inside the oven cavity. See the “Extendable Roller Rack” section in the Use and Care Guide.
WARNING
Excessive Weight Hazard
Use two or more people to move and install oven doors.
Failure to do so can result in back or other injury.
7. Tighten the gas pressure regulator cap by using a large flat-
blade screwdriver, turning the regulator cap clockwise.
8. Test the gas pressure regulator and gas supply line.
The regulator must be checked at a minimum 1" (2.5 cm) water column above the set pressure. The inlet pressure to the regulator should be as follows for operation and checking the regulator setting:
LP Gas:
Minimum pressure 11" (27.9 cm) WCP Maximum pressure 14" (35.6 cm) WCP
2. Remove the oven door. See the “Oven Door” section in the
Use and Care Guide.
3. Slide the bake burner cover to the right or left.
A
A. Bake burner cover
4. Lift up and remove oven bake burner cover and set aside.
4
Loading...
+ 8 hidden pages