Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
can be killed or seriously injured if you don't
You
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can
happen if the instructions are not followed.
3
BeforeUsing Your Dishwasher
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
■ Install where dishwasher is protected from the elements.
Protect against freezing to avoid possible rupture of fill valve.
Such ruptures are not covered by the warranty. See “Storing”
in the “Dishwasher Care” section for winter storage
information.
■ Install and level dishwasher on a floor that will hold the
weight, and in an area suitable for its size and use.
■ Remove all shipping plugs from hoses and connectors (such
as the cap on the drain outlet) before installing. See
Installation Instructions for complete information.
4
PARTS AND FEATURES
M
G
A
B
C
H
I
J
D
E
F
A. Upper level wash
B. 3-position adjuster
C. Water inlet opening (in tub wall)
D. Bottom rack
E. Rack bumper
F. Heating element
G. Top spray arm
H. Model and serial number label
I. Filter module
K
L
N
J. Lower spray arm
K. Silverware basket
L. Overfill protection float
M. Detergent dispenser
N. Rinse aid dispenser
Control Panel
5
START-UP GUIDE
Before using your dishwasher, remove all packaging materials.
Read this entire Use and Care Guide. You will find important
safety information and useful operating tips.
Using Your New Dishwasher
1. Scrape large food soil and hard items (toothpicks or bones)
from dishes.
2. Properly load the dishwasher. (See “Dishwasher Loading.”)
Make sure nothing prevents the spray arm(s) from spinning
freely.
3. Add detergent and check the rinse aid dispenser. Add rinse
aid if needed. (See “Dishwasher Use.”)
DISHWASHER LOADING
Loading Suggestions
■ Remove leftover food, bones, toothpicks and other hard
items from the dishes. It is not necessary to rinse the dishes
before putting them into the dishwasher. The wash module
removes food particles from the water. The module contains a
chopping device which will reduce the size of food items.
NOTE: If hard items such as fruit seeds, nuts, and eggshells
enter the wash module, you might hear chopping, grinding,
crunching, or buzzing sounds. These sounds are normal
when hard items enter the module. Do not let metallic items
(such as pot handle screws) get into the wash module.
Damage can occur.
■ It is important for the water spray to reach all soiled surfaces.
■ Load dishes so they are not stacked or overlapping, if
possible. For best drying, water must be able to drain from all
surfaces.
■ Make sure pot lids and handles, pizza pans, cookie sheets,
etc., do not interfere with the spray arm rotation.
■ Run a rinse cycle to keep dishes moist if you do not plan to
wash them soon. Foods such as eggs, rice, pasta, spinach,
and cooked cereals may be hard to remove if they are left to
dry over a period of time.
4. Push door firmly closed. The door latches automatically. Run
hot water at the sink nearest your dishwasher until the water
is hot. (See “Dishwasher Efficiency Tips.”) Turn off water.
5. Select the desired cycle and options. (See “Dishwasher
Use.”)
6. Press START/RESUME.
Stopping Your Dishwasher
You can stop your dishwasher anytime during a cycle.
1. Open the door slightly.
2. Wait for the spraying action to stop. Then open the door all
the way, if needed.
Close the door to continue the cycle.
OR
Press CANCEL/DRAIN. A 2-minute drain starts.
Quiet operating tips
To avoid thumping/clattering noises during operation:
■ Make sure lightweight load items are secured in the racks.
■ Make sure pot lids and handles, pizza pans, cookie sheets,
etc., do not touch interior walls or interfere with the rotation of
the spray arm.
■ Load dishes so they do not touch one another.
NOTE: For built-in models, keep sink drain plugs closed during
dishwasher operation to prevent noise transfer through drains.
Loading Top Rack
The top rack is designed for cups, glasses, and smaller items.
(See recommended loading patterns shown.)
NOTE: The features on your dishwasher rack may vary from the
drawings shown.
Cup and glass load
6
Mixed load
■ Place items so open ends face down for cleaning and
draining.
■ Load glasses in top rack only. The bottom rack is not
designed for glasses. Damage can occur.
■ Place cups and glasses in the rows between tines. Placing
them over the tines can lead to breakage.
■ China, crystal, and other delicate items must not touch each
other during dishwasher operation. Damage may occur.
■ Load plastic items in the top rack only. Only plastic items
marked “dishwasher safe” are recommended.
■ Load plastic items so the force of the spray does not move
them during the cycle.
■ To avoid chipping, do not let stemware touch other items.
■ Small bowls, pans, and other utensils can be placed in the
top rack. Load bowls in the center section for best stability.
Adjustable 3-position top rack
Loading Bottom Rack
The bottom rack is designed for plates, pans, casseroles, and
utensils. Items with cooked-on or dried-on food should be loaded
with soiled surfaces facing inward to the spray. (See
recommended loading patterns shown.)
NOTE: The features on your dishwasher rack may vary from the
drawings shown.
Do not cover spray tower. See arrow.
Mixed load
■ Do not load glasses, cups, or plastic items in the bottom
rack. Load small items in the bottom rack only if they are
secured in place.
■ Load plates, soup bowls, etc., between tines and facing
inward to the spray.
■ Overlap the edges of plates for large loads.
■ Load soup, cereal, and serving bowls in the rack in a variety
of ways depending upon their size and shape. Load bowls
securely between the rows of tines. Do not nest bowls
because the spray will not reach all surfaces.
You can raise or lower the top rack to fit tall items in either the top
or bottom rack. Two adjusters are located on each side of the top
rack. Each adjuster has 3 preset positions. The high and low
positions are marked on the adjuster.
To adjust the top rack
1. Hold the top rack with one hand near the adjuster.
2. With the other hand, pull out the top of the adjuster.
3. Raise or lower the rack to one of the preset positions.
4. Release the adjuster.
Repeat the steps for the remaining adjusters as needed. The
4 adjusters can be raised or lowered separately or together. The
top rack does not have to be level.
Utensil load
■ Load cookie sheets, cake pans, and other large items at the
sides and back. Loading such items in front can keep the
water spray from reaching the detergent dispenser and
silverware basket.
■ Secure heavily soiled cookware face down in the rack.
■ Make sure pot handles and other items do not stop rotation
of the spray arm(s). The spray arm(s) must move freely.
■ Do not load items between the bottom rack and the side of
the dishwasher tub. You can block the water inlet opening.
NOTE: If you have removed the bottom rack for unloading or
cleaning, replace it with the bumpers in front.
7
Loading Silverware Basket
Load the silverware basket while it is in the bottom rack or take
the basket out for loading on a counter or table.
NOTE: Unload or remove the basket before unloading the racks
to avoid spilling water droplets onto the silverware.
DISHWASHER USE
Detergent Dispenser
The detergent dispenser has 2 sections. The Pre-Wash section
empties detergent into the dishwasher when you close the door.
Mix items in each section of the basket with some pointing up
and some down to avoid nesting. Spray cannot reach nested
items.
■ Do not load silver or silver-plated silverware with stainless
steel. These metals can be damaged by contact with each
other during washing.
■ Some foods (such as salt, vinegar, milk products, fruit juices,
etc.) can pit or corrode silverware. Run a rinse cycle if you do
not have a full load to wash immediately.
A
The larger Main Wash section automatically empties detergent
into the dishwasher during the main wash. (See the “Cycle
Selection Charts.”)
■ Use automatic dishwashing detergent only. Other detergents
can produce excessive suds that can overflow out of the
dishwasher and reduce washing performance.
■ Add detergent just before starting a cycle.
■ Store tightly closed detergent in a cool, dry place. Fresh
automatic dishwasher detergent results in better cleaning.
NOTE: Do not use detergent if you have selected a rinse cycle.
BCD
A. Cover
B. Main Wash section
C. Cover latch
D. Pre-Wash section
Filling the dispenser
1. If the dispenser cover is closed, open the cover by pushing
the Cover latch.
2. Fill the Main Wash section with detergent. See “How much
detergent to use.”
3. Fill the Pre-Wash section if needed. (See “Cycle Selection
Charts.”)
4. Close the dispenser cover.
The cover will open during the cycle to dispense the detergent.
How much detergent to use
■ The amount of detergent to use depends on the hardness of
your water and the type of detergent. If you use too little,
dishes won’t be clean. If you use too much in soft water,
glassware will etch.
■ Water hardness can change over a period of time. Find out
your water’s hardness by asking your local water department,
water softener company, or county extension agent.
8
Where to fill
Top of 3rd step (9 tsp or 45 mL)
Top of 2nd step (6 tsp or 30 mL)
Top of 1st step (3 tsp or 15 mL)
Soft to Medium Water (0-6 grains per U.S. gallon)
[typical water softener water and some city water]
Filling the dispenser
The rinse aid dispenser holds 6 oz (175 mL) of rinse aid. Under
normal conditions, this will last for about 3 months. You do not
have to wait until the dispenser is empty to refill it. Try to keep it
full, but be sure not to overfill it.
1. Make sure the dishwasher door is completely open.
2. Remove the fill indicator cap.
3. Add rinse aid. Fill to the smallest opening in the lower part of
the dispenser. Overfilling can cause the rinse aid to leak out,
and could cause oversudsing.
Soil LevelMain WashPre-Wash
Lightly soiled/Prerinsed dish loads
Normally soiled
dish loads
Heavily soiled
dish loads
3 tsp (15 mL)
[top of 1st step]
6 tsp (30 mL)
[top of 2nd step]
9 tsp (45 mL)
[top of 3rd step]
3 tsp (15 mL)
[top of 1st step]
6 tsp (30 mL)
[top of 2nd step]
6 tsp (30 mL)
[top of 2nd step]
Medium to Hard Water (7-12 grains per U.S. gallon)
[well water and some city water]
Soil LevelMain WashPre-Wash
All soil types9 tsp (45 mL)
[top of 3rd step]
6 tsp (30 mL)
[top of 2nd step]
NOTE: Fill amounts shown are for standard powdered detergent.
Amounts may vary if you use liquid or concentrated powdered
detergent. Tablet detergents should be placed in the main wash
section of the detergent dispenser with the cover closed. Follow
instructions on the package when using liquid dishwasher
detergent, concentrated powdered detergent or tablet detergent.
IMPORTANT: See “Cycle Selection Charts” for which detergent
dispenser sections to use with each cycle.
Rinse Aid Dispenser
Rinse aids prevent water from forming droplets that can dry as
spots or streaks. They also improve drying by allowing water to
drain off of the dishes during the final rinse by releasing a small
amount of the rinse aid into the rinse water. Your dishwasher is
designed to use a liquid rinse aid. Do not use a solid or bar-type.
Checking the dispenser
Check the center of the fill indicator cap. Clear means it needs
filling.
OR
Or you can remove the fill indicator cap. If an “E” is visible, the
dispenser is empty.
4. Clean up any spilled rinse aid with a damp cloth.
5. Replace the fill indicator cap. Close tightly.
DishwasherEfficiency Tips
Hot water dissolves and activates the dishwashing detergent.
Hot water also dissolves grease on dishes and helps glasses dry
spot-free. For best dishwashing results, water should be 120°F
(49°C) as it enters the dishwasher. Loads may not wash as well if
the water temperature is too low. Water that is too hot can make
some soils harder to remove and cause certain detergent
ingredients not to function. If your water heater is located far from
the dishwasher, it may be necessary to run the hot water at the
faucet closest to the dishwasher to minimize the amount of cold
water in the water line.
To check water temperature
1. Run hot water at the faucet closest to your dishwasher for at
least 1 minute.
2. Place a candy or meat thermometer in a glass measuring
cup.
3. Check the temperature on the thermometer as the water is
running into the cup.
■ To save water, energy and time, do not rinse dishes before
putting them into the dishwasher.
■ Use a low energy, quick, or short cycle whenever possible.
These cycles use less hot water and energy than a normal
cycle.
■ Use a delay feature (on some models) to run your dishwasher
during off-peak hours. Local utilities recommend avoiding
heavy usage of energy at certain times of day.
■ During the summer, run your dishwasher at night. This
reduces daytime heat buildup in the kitchen.
■ Use the energy-saving dry option whenever possible. Allow
longer drying times (overnight) when using these options. Use
a rinse aid to improve drying.
9
■ Use cycles or options that add extra heat to the wash or rinse
portion of the cycle only when needed.
■ Run your dishwasher with full loads. Run a rinse cycle after
meals until the dishwasher is full.
■ If your home is equipped with a water softener, you may want
to avoid starting the dishwasher during the regeneration of
the softener, since this may contribute to poor wash
performance.
Cycle Selection Charts
Select the wash cycle and options desired and press START/
RESUME. The dishwasher starts filling once you press START/
RESUME, unless you select a delay wash. You can select an
option as the machine is filling.
After a wash cycle, the dishwasher remembers the options used
and uses the same options in the next wash cycle unless new
options are selected or Cancel/Drain is selected.
A “●” shows what steps are in each cycle. Your model may have
some or all of the cycles shown.
Temperatures indicate where extra heat is added.
Water usage is shown in U.S. gallons/liters.
These models meet the ENERGY STAR® guidelines for energy
efficiency.
Cycle time includes dry time. An asterisk ( * ) by the cycle time
indicates the cycle time might be longer depending on the
temperature of the water entering the dishwasher. The cooler the
water, the longer the cycle time. If the water is already hot
enough, the cycle time will be as shown.
Pots & Pans
Use this cycle for hard-to-clean, heavily soiled pots, pans,
casseroles, and regular tableware.
Normal Wash
Use this cycle for loads with normal amounts of food soil. (The
energy-usage label is based on this cycle.)
Use covered detergent dispenser section.
Pre-
Wash
RinseMain
Rinse Purge†Final
Wash
●●
Rinse
140°F
(60°C)
●●
DryTime
(min)
61*4.8/18.0
Water
Usage
(gal/L)
Light Wash
Use this cycle for prerinsed or lightly soiled loads.
Use covered detergent dispenser section.
Pre-
Wash
RinseMain
Rinse Purge†Final
Wash
●●
Rinse
140°F
(60°C)
●●
DryTime
(min)
58*4.8/18.0
Water
Usage
(gal/L)
Rinse Only
Use this cycle for rinsing dishes, glasses, and silverware that will
not be washed right away.
Do not use detergent with this cycle.
Use both detergent dispenser sections.
Pre-
Wash
140°F
(60°C)
●
RinseMain
Rinse Purge†Final
Wash
140°F
(60°C)
●●
Rinse
140°F
(60°C)
●●
Heavy Wash
Use this cycle for loads with heavy food soil.
Use both detergent dispenser sections.
Pre-
RinseMain
Wash
●●●
Rinse Purge†Final
Wash
Rinse
140°F
(60°C)
●●
DryTime
(min)
87*8.6/32.6
DryTime
(min)
72*6.9/26.1
Water
Usage
(gal/L)
Water
Usage
(gal/L)
Pre-
RinseMain
Wash
†
A small amount of water runs through the pump to remove soil
Rinse Purge†Final
Wash
●
Rinse
DryTime
(min)
102.2/10.0
Water
Usage
(gal/L)
particles.
Canceling aCycle
Anytime during a cycle, press CANCEL/DRAIN. Cancel/Drain
glows. The dishwasher pauses for about 5 seconds and starts a
2-minute drain (if needed). Let the dishwasher drain completely.
The light goes off when the dishwasher finishes the drain.
To stop the drain
You can press CANCEL/DRAIN again to stop the drain
immediately. Remember to drain the dishwasher before starting a
new cycle.
NOTE: A small amount of water remains in the dishwasher. This
is normal.
To clear the indicators
Press CANCEL/DRAIN before starting the dishwasher to clear all
options and cycles.
10
Changing a Cycleor Setting
During the first 2 minutes of a cycle
Press a new cycle and/or options.
After the first 2 minutes of a cycle
1. Press CANCEL/DRAIN. Cancel/Drain glows. The dishwasher
pauses for 5 seconds and starts a 2-minute drain (if needed).
Let the dishwasher drain completely.
2. Check the detergent dispensers. If the main wash cup has
opened and the detergent washed away, refill the cups as
needed.
3. Close the door.
4. Press a new cycle and/or options and press START/
RESUME.
Adding ItemsDuring aCycle
You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the main wash
section is still closed, you can add items.
Heated Dry
Select this option to dry dishes with heat.
Switching off Heated Dry saves energy and is useful when loads
contain plastic dinnerware that may be sensitive to high
temperatures. The dishes take longer to dry, and some spotting
can occur.
For best drying, use a liquid rinse aid. Some items (such as
plastics) may need towel drying.
NOTE: Heated Dry is an option with all cycles except Rinse Only.
Locked
Use Locked to prevent unintended use of the dishwasher. You
can also use the Locked feature to prevent unintended cycle or
option changes during a cycle.
NOTE: When Locked is lit, all buttons are disabled.
To lock the controls
Press and hold
To add items
1. Lift up the door latch to stop the cycle. Wait for the spraying
action to stop before opening the door.
2. Open the door. If the main wash detergent dispenser is still
closed, add the item.
3. Close the door, but do not latch it. Wait 30 seconds for the air
in the dishwasher to warm up. This reduces the amount of
moisture escaping from the vent when restarting a cycle.
4. Close the door firmly until it latches and press START/
RESUME. The dishwasher resumes the cycle after about a
5-second pause.
Option Selections
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn off the option.
Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
anytime before drying begins.
After a wash cycle, the dishwasher remembers the options used
and uses the same options in the next wash cycle, unless you
select new options or press CANCEL/DRAIN.
Hi-Temp Wash
Select this high-temperature option for improved cleaning of
heavily soiled dishes. Selecting this option adds heat, water and
time to the wash cycle. Heating the water helps improve washing
results.
NOTE: Hi-Temp Wash is an option with Heavy wash and Normal
wash.
for 5 seconds. Locked glows. If you press any pad while your
dishwasher is locked, the light flashes 3 times.
To unlock the controls
Press and hold HEATED DRY for 5 seconds until the light turns
off.
NOTE: The dishwasher door can be opened while the controls
are locked.
Delay Hours
Use Delay Hours to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay countdown. After adding items, close the door firmly until it
latches. The delay countdown will not continue if the door is not
latched.
To delay the start
1. Close the door.
2. Press DELAY 1 time for a 2-hour delay, 2 times for a 4-hour
delay, or 3 times for a 6-hour delay.
3. Select a wash cycle and option.
The number glows above Delay. The dishwasher starts the cycle
in the selected number of hours. If you do not press a cycle
within 30 seconds, the Delay indicator turns off.
NOTES:
■ To cancel the delay and cycle, press CANCEL/DRAIN.
■ To cancel the delay and start the cycle, press START/
RESUME.
11
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.