Whirlpool S27C FWW2XDF, S29DG DWW3 DF, S25C RWW2 DF, S25C RTT3 DF, S27C FSS3DF Installation Manual

10200175GB.fm Page 24 Monday, July 18, 2005 11:23 AM

INSTALLATION

BEFORE INSTALLING THE REFRIGERATOR ..................25

PRECAUTIONS AND GENERAL

RECOMMENDATIONS......................................................25

WATER CONNECTION.....................................................26

ELECTRICAL CONNECTION ............................................26

LEVELLING YOUR REFRIGERATOR.................................27

REMOVING THE FREEZER DOOR (A) .............................28

REMOVING THE REFRIGERATOR DOOR (B) .................28

MOUNTING THE FREEZER DOOR (C) ............................29

MOUNTING THE REFRIGERATOR DOOR (D)................29

HORIZONTAL ALIGNMENT OF FREEZER AND

REFRIGERATOR DOORS (E).............................................30

VERTICAL ALIGNMENT OF FREEZER AND

REFRIGERATOR DOORS (F).............................................30

24

10200175GB.fm Page 25 Monday, July 18, 2005 11:23 AM

BEFORE INSTALLING THE REFRIGERATOR

Foreword

Your new appliance is a FULL NO FROST model
exclusively for domestic use, i.e. both refrigerator and
freezer compartments are provided with an automatic
defrosting function.

This manual contains indications and warnings for correct
and safe installation of the appliance - read it carefully
before starting installation operations.

The model you have purchased may differ slightly with
respect to some descriptions in this manual, since this
manual covers several models.
Keep this manual for future consultation. If you sell the
appliance give it to the new buyer.

Disposal of packaging materials

The packaging material for the protection and transport of
the appliance and single components is entirely recyclable,
and marked with the recycling symbol .

Keep the packaging materials (plastic bags, polystyrene
parts, etc.) out of reach of children, as they are potentially
dangerous.

Disposal must be carried out in accordance wi th local
regulations for waste disposal .

PRECAUTIONS AND GENERAL
RECOMMENDATIONS

After unpacking the appliance, check for damage and make
sure that the doors shut properly. Any damage must be
reported to your dealer within 24 hours after delivery of the
appliance.
Be careful not to damage the floors when you move the
appliance (e.g. parquet flooring). If, after removing the
doors, it is necessary to move the appliance, make sure
the internal components are well secured and/or remove
them in order to avoid damage.
Because of the weight of the appliance, at least 2 persons are
required to safely move/install it.
Installation of the appliance must be carried out by a qualified
technician.
Wait at least 1 hour before connecting the appliance to
the power supply in order to ensure the refrigerant
circuit is fully efficient.
Depending on the model purchased, the appliance does
not contain CFCs (if the refrigerant circuit contains
R134a) or HFCs (if the refrigerant circuit contains R600a

- Isobutane). Isobutane is a natural gas with low
environmental impact. Caution is required, however,
since isobutane is flammable. Therefore, it is essential to
ensure that refrigerant pipelines are not damaged.
Data regarding refrigerant and insulating substance s i s
given on the rating plate.
Clean the inside of the appliance before introducing food.
For correct and safe operation, install and connect the
appliance according to the instructions given in this
manual.

The appliance is set for optimum operation at specific
ambient temperature ranges, according to the climatic
class indicated on the data plate:

Climatic class Amb. T. (°C) Amb. T. (°F)

SN From 10 to 32 From 50 to 90

N From 16 to 32 From 61 to 90

ST From 18 to 38 From 64 to 100

T From 18 to 43 From 64 to 110

The appliance may not work properly if it is left for a long
period at a temperature above or below the indicated
range.

Temperature inside the compartments may be
influenced by various factors such as: position of the
appliance, ambient air temperature, frequency of door
opening.

Install the appliance in a dry and well-venti lated place.
Avoid locations in direct sunlight or near a source of heat

(oven, heating, etc.). If this cannot be avoided, install the
appliance respecting the following minimum distances:

Coal or paraffin stoves: 30 cm
Electric and/or gas stoves: 3 cm

Install and level the appliance on a floor strong enough to
take its weight and in an area suitable for its size and use.
To allow product handling and sufficient air circulation,
leave at least 1 cm clearance at the sides, above the
appliance, and between the rear panel and the wall.

25

10200175GB.fm Page 26 Monday, July 18, 2005 11:23 AM

ATER CONNECTION

W

Disconnect the appliance from the mains power supply
before starting operations.

•

The ice maker and water circuit must be connected to a water supply of
potable and/or chemically purified water.

•

The water connection must be carried out in compliance with local
regulations.

•

The appliance is supplied with a water tube, 2.330 m long, already
attached to the back of the product.

•

Remove the shipping tape from the gray coiled water tubing on the rear
of the appliance.

•

Connect the transition connector (1) to the household water supply (2).

•

Make sure that the water tube is not twisted.

•

The appliance is pre-set for operation at pressures between 1.7 and 8.1
bar (25 and 117 PSI).

•

Open the water tap. Check for and eliminate any leaks.

•

The appliance does not require any adjustment or water drain.

ELECTRICAL CONNECTION

Regulations require that the appliance is earthed. The manufacturer
declines all liability for injury to persons or animals and for damage to
property resulting from failure to observe the prescriptions.
Make sure that the installation and the electrical connection are carried out
by a qualified technician according to the manufacturer’s instructions and
local safety regulations.
If your new appliance is provided with a plug with no earth wire, connect
your green/yellow earth wire (A) to the earth screw located on the
appliance (B) (see figure).
Ensure that the voltage indicated on the appliance data plate corresponds to
the mains voltage.
The plug of the appliance must be easily accessible even after installation so
that the appliance can be unplugged if necessary. If this is not possible,
connect the appliance to the mains supply by means of a two-pole switch
with minimum break distance between contacts of 3 mm, fitted at an easily
accessible point.
If the power supply cable plug and socket are not of the same type, replace
the socket.
Do not use extension leads or adapters.
After installation, make sure that the appliance is not standing on the power
supply cable.
Disconnect the appliance from the power supply by unplugging it. Do not
pull the power supply cable.

26