GB PWA 1027
A. Programme selector
B. Programme sequence indicator
C. “Start/Pause” button
D. “Reset” button
E. “Door open” indication
PROGRAMME CHART
H F
This washing machine is equipped with
B
EG
D
A
C
automatic safety functions which detect and
diagnose faults at an early stage and react
appropriately:
F. “Service” indication
G. “Water tap closed” indication
H. “Clean pump” indication
1)
Do not use liquid detergent.
2)
For improved garment care, spin speed is restricted
to 400 rpm in this programme.
Max.
Programme
Cotton with rewash
95 °C
Cotton
40 - 60 - 95 °C
Synthetics with prewash
60 °C
Synthetics
30 - 40 - 60 °C
Delicates
30 °C
Quick wash
30 °C
Wool
Cold - 40 °C
Handwash
30 - 40 °C
Rinse & Spin – 5.0 Same as the last rinse and the final spin in the “Cotton” programme. – –
95°C
40 - 60 - 95°C
60°C
30 - 40 - 60°C
30°C
30°C
- 40°C
30 - 40°C
Care
Labels
Load
kg
5.0 Heavily soiled whites such as bed linen, table linen, underwear and towels made of cotton and linen. Yes Yes
5.0
2.5
2.5
1.5 Curtains and delicate clothing, dresses, skirts, shirts and blouses. – Yes
3.0 Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton. – Yes
1.0 Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable. – Yes
1.0 Textiles made of linen, silk, wool and viscose marked as “handwashable”. – Yes
- for temperature selection, respect the manufacturer's recommendations on the care label
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and
linen.
Normally to heavily soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide
(Perlon, Nylon) or blends with cotton.
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon,
Nylon) or blends with cotton.
Type of wash / Notes
Detergents and Additives Special options Max.
Pre-
wash
Main
Wash
Softener Intensive
rinse
Spin speed
reduction
500
– Yes
Yes Yes
– Yes
1)
1)
i i i
i i i
i i i
i i i
i
i i i
i
i
i i i
–
–
– – 400
i
i
Spin
Speed
rpm
1000
1000
1000
1000
1000
1000
1000
2)
1000
Spin – 5.0 In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme. – – – –
Gentle Spin – 1.0 In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme. – – – –
Drain – – Drain only - no spinning. – – – – – –
N.B. This machine is controlled by sensors. Please avoid excessive detergent dosing.
i
i
1000
1000
5019 812 10044
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
Cotton 95 5.0 50* 1.70 2:05
Cotton** 60 5.0 55 0.95 2:10
Cotton 40 5.0 55 0.55 2:00
Synthetics 60 2.5 50* 0.80 1:30
Synthetics 40 2.5 45 0.45 1:15
Delicates 40 1.5 50 0.55 0:45
Quick wash 30 3.0 35 0.40 0:30
Wool 40 1.0 55 0.55 0:45
Handwash 40 1.0 40 0.40 0:35
Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in
compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to
the water supply pressure and temperature, the load and the type of wash.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water
out.
** Reference Programme for Energy Label.
PREPARATION OF THE WASH CYCLE
1. Load the machine, close the drum doors and check
that they are properly locked.
2. Add detergent and additives into the dispenser to
no more than the “MAX” level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Stain remover agents
• Anti-scale agents (if necessary)
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The lamp next to the
“Start/Pause” button flashes.
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been executed yet.
“Intensive rinse” button
• The amount of water is increased to ensure a more
intensive rinse.
• This option is particularly suitable for areas with very
soft water, washing baby linen and people with skin
allergies.
“Spin speed reduction” button
500
• Reduces the predetermined automatic maximum
spin speed to treat your laundry more gently.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause” button
lights up. The programme sequence indicator shows
the current programme phase, running from left to right
through Wash, Rinse, Spin/Drain. When the programme
phrase is finised, the corresponding indication goes out.
• Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a
wash programme is running, the lid remains locked and
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to “Cancel (Reset) a running programme before
the end”.
RED INDICATIONS
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for Use”;
if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap: if the indications still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use (“Removing
the Filter”).
PROGRAMME END
• All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the lid and drum and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Select the new programme, any options and another
spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the
end. Press the “Reset” button for at least 3 seconds.
Any existing water is drained out before the door can be
opened.
5019 812 10044