Whirlpool MAX 18 AW User Manual

SERVICE

Model MAX 18/AW
Version 8538 018 99261 Page

Whirlpool Europe
Customer Services

MAX 18/AW

Service Manual

Microwave oven
MAX 18/AW

Introduction safety 2

Technical data 3

Spare part list 4

Exploded view 5

Wiring diagram 6 - 7

This documentation is only intended for qualified technicians who are aware of the respec­tive safety regulations.
Date: 01.09.2003 (Mod. 01) Subject to modification
Document-No.: 4812 714 14499

10.01.2003 / Page 2 MAX 18/AW Whirlpool Europe
Doc. No: 4812 714 14499 8538 018 99261 Customer Service

SERVICE

Introduction safety

INTRODUCTION

Before leaving the factory each oven is carefully checked.
It must, however, be installed and used correctly.

Despite all the steps taken to make the oven safe, the safety is dependent on the correct installation and the fact
the user understands how to use and maintain the oven.

The information in this section should be used as a reminder that the oven is safe and that anyone who uses it must
first read the instructions for use in order to be able to use the oven correctly and obtain best results.

SAFETY

To avoid injury to yourself and damage to the appliance always work to the following rules when servicing an oven.

Always disconnect the plug from the mains before starting work.

If there is no plug switch off the electric supply at the control box.

When you have finished servicing an oven before you reconnect it to the mains, make sure that:

- all the internal connections are correct

- the wires are insulated and not touching the door or the cabinet or anything sharp

- all the earth connections are electrically and mechanically sound

- do not modify or anyway interfere with the safety devices built-in to the oven

- make sure that each replacement part you use conforms to the manufacturer´s specifications

Do not start a repair if you have any doubt as to your ability to complete it.

CAUTION - MICROWAVE RADIATION

PERSONNEL SHOULD NOT BE EXPOSED TO THE MICROWAVE ENERGY WHICH MAYRADIATE FROM THE MAGNETRON,

WAVEGUIDE OR ANTENNA IF THEY ARE IMPROPERLY USED OR CONNECTED. ALL INPUT
AND OUTPUT MICROWAVE CONNECTIONS, WAVEGUIDES, FLANGES AND GASKETS MUST BE SECURE.
NEVER OPERATE THE DEVICE WITHOUT A MICROWAVE ENERGY ABSORBING LOAD ATTACHED.
NEVER LOOK INTO AN OPEN WAVEGUIDE OR ANTENNA WHILE THE DEVICE IS ENERGIZED.
NEVER OPERATE AN OVEN WITH CABINET OFF WITHOUT MEASURING THE MICROWAVE LEAKAGE
AROUND MAGNETRON AND VISIBLE MICROWAVE CONNECTIONS (WELDING JOINTS).

Do not operate the oven if the following conditions exist:

- the door does not close firmly against the door support because of the door being warped or the hinges damaged.

- The door trims or seals are damaged.

- If there is any visible damage to the oven.

- if the door does not close properly.

Avoid operating the oven if known components in the interlock system, oven door or microwave
generating assembly are known defective. They must be replaced.

WARNING - HIGH VOLTAGE

IT IS POSSIBLE TO COME IN CONTACT WITH LETHAL HIGH VOLTAGE WHEN WORKING WITH
HV TRANSFORMER, HV CAPACITOR AND MAGNETRON. THEREFORE NEVER TRY TO MEASURE
THE HIGH VOLTAGE. ALWAYS TAKE UTMOST CARE WHEN PERFORMING ELECTRIC
MEASUREMENTS INSIDE THE OVEN.

SERVICE

Technical data

Whirlpool Europe MAX 18/AW 01.09.2003 (Mod. 01) / Page 3
Customer Service 8538 018 99261 Doc. No: 4812 714 14499

Product dimensions

Height 356 mm
Width 392 mm
Depth 350 mm

Cavity dimensions

Height 149 mm
Width 290 mm
Depth 290 mm
Cavity volume 13 l
Turntable diameter 280 mm

Weight

Net 12 kg
Gross 13 kg

Error codes

Certain fault conditions are indicated by an error code.
The following codes are implemented:

Electrical

Voltage 230 V
Frequency 50 Hz
Fuse 10 A
Current consumption 6 A

Power

Power consumption 1300 W
Output power MW 750 W
Grill 600 W
Maximum input power 1750 W

Timer

electronic 30 min.

5 power levels

ERR 0 Convection temperature sensor fault.

Not connected or short circuit.

ERR 1 Short circuit in the MW relay.

ERR 6 Weight sensor calibration has not been performed.

ERR 7 Humidity sensor is defect or has not been connected.

ERR 8 Impossible to write to E2 PROM.

ERR 9 Options have not been set.

ERR A No wheel detected on weight sensor.

ERR B No pulses from the weight sensor or <4267 Hz.

ERR C Fuzzy temperature sensor fault. Not 19-41 ˚C.