Whirlpool KDFX 6040 INSTRUCTION FOR USE

KDFX 6040

Product sheet

Quick Reference Guide / Overview	4
Quick Reference Guide	5
How to use the appliance	8
Precautions and general recommendations	13
What to do if...	14

Quick Reference Guide / Overview

Before using the dishwasher, read the installation and maintenance instructions carefully!

On button

Off button

Programme selection button

Press button P (repeatedly) to bring up the number of the desired programme on the display.

Time and failure display

With normal operation, the display indicates residual time (h:min), while with the "Delayed start" function selected it indicates time remaining until the start of the programme (hh).

If "F.." appears on the display, see chapter "What to do if..."!

Rinse aid level indicator and Salt level indicator

These indicator lamps light up when rinse aid or salt to be added. Add just before starting a wash programme.

Select detergent

Press the button repeatedly to select the type of detergent used.

Powder, gel, tab (standard): indicator off Detergent with rinse aid: left indicator Detergent with salt + rinse aid: right indicator This deactivates the rinse aid and/or salt indicator lamp.

Half Load/Multizone button Load the upper or lower rack only. Press once = wash upper rack (the indicator/symbol lights up)

Press twice = wash lower rack (the indicator/symbol lights up)

Press 3 times = Off (Half load/Multizone deactivated).

When washing without the upper rack, press the "Half load" (i.e. "wash bottom rack") button twice (the corresponding indicator/symbol lights up).

Antibacterial rinse 3)

This function activates an antibacterial rinse at the end of the wash cycle, guaranteeing a further reduction of bacteria. Press the button to activate or deactivate the function. This function can be used with those programmes marked with the relative symbol in table 1.1.

The dishwasher door must be kept shut for the entire duration of the programme in order to guarantee reduction of bacteria. If the door is opened the indicator lamps starts flashing.

"Delayed start" button

Press the button repeatedly to delay the start of the programme. Delay adjustable from 1 to 24 hours. With successive touch of the button, the delay start indicator increases by one hour and after 24 returns to 00. Then press the start button. The dishwasher will start at the set time.

Start button

Switches "on" when the dishwasher is operating. Flashes when a fault occurs.

Switches off at the end of the programme.

Reset button - for changing programme or failure display

Press this button to cancel a started programme and selected options. Press this button to cancel the main fault indicators (F..), for fault details consult chapter "What to do if ...). A new programme can then be selected and started.

4

Quick Reference Guide

Table 1.1

P

1

2

3

4

5

6

7

				Programme Chart			Detergent		Consumption 1)
							dispenser
					Selectable
		Programmes			extra	Loading instructions	large	small	Litres	kWh	Min
					function
						Automatic programme
			Sensor +	40-70°C		recommended for routine	X	X	7-17	0.99-1.75	65-
						washes, with dried-on food					220 ± 1)
						(for example for EN 50242).
			Pre-Rinse	cold		Crockery to be washed later.	-	-	4.0	0.03	14 ± 1)
			Glass	40°C		Light soiling, for example	X	-	10.0	0.85	100 ± 1)
						glasses and cups.
			Quickwash 40°C			Lightly soiled crockery with	X	-	10.0	0.65	30 ± 1)
						no dried-on food.
						Normally soiled crockery.
			Eco2)	50°C		Energy saving programme	X	X	11.0	1.05	155 ± 1)
						with prolonged drying cycle.
						Very dirty dishes or stubborn					200-
			Pro Clean			grime.	X	X	15.0-19.0	1.90-2.05
											220 ± 1)
						e.g. pots and pans.
						Normally soiled crockery,
			Overnight	55°C		gentle and quiet programme	X	X	13.0	1.20	290 ± 1)
						thanks to the low spray
						pressure (39dbA).

1)Programme data obtained in conformity with European standard EN 50242. The data may vary, according to different loads, different extra functions, different sensor settings (for sensor programmes only), different water supply temperatures, different water hardnesses, different power supply voltages, etc.

2)Reference programme for energy label in compliance with EN 50242 - Important Information for Test Laboratories: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: [e-mail].

3)The bacteria removal efficiency has been tested by the Institut Pasteur de Lille (France), based on the NF EN 13697 standard of November 2001.

5