Whirlpool KDFX 6033 INSTRUCTION FOR USE
KDFX 6033
Product sheet
Quick Reference Guide / Overview 4
Quick Reference Guide 5
How to use the appliance 8
Precautions and general recommendations 13
What to do if... 14
4
Before using the dishwasher, read the
installation and maintenance instructions
carefully!
On button
Off button
Programme selection button
Press button P (repeatedly) to bring up the number
of the desired programme on the display.
Time and failure display
With normal operation, the display indicates residual
time (h:min), while with the "Delayed start" function
selected it indicates time remaining until the start of
the programme (hh).
If "F. . " appears on the display, see chapter "What to do
if..."!
An acoustic alarm will warn that a fault is present, and
will continue until the fault itself is resolved.
Rinse aid level indicator and Salt level
indicator
These indicator lamps light up when rinse aid or salt
to be added. Add just before starting a wash
programme.
Select detergent
Press the button repeatedly to select the type of
detergent used.
Powder, gel, tab (standard): indicator off
Detergent with rinse aid: left indicator
Detergent with salt + rinse aid: right indicator
This deactivates the rinse aid and/or salt indicator
lamp.
Running Program Indicator
A LED light projected on the floor indicates that the
dishwasher is working.
Half Load/Multizone button
Load the upper or lower rack only.
Press once = wash upper rack (the
indicator/symbol lights up)
Press twice = wash lower rack (the
indicator/symbol lights up)
Press 3 times = Off (Half load/Multizone
deactivated).
When washing without the upper rack, press the
"Half load" (i.e. "wash bottom rack") button twice
(the corresponding indicator/symbol lights up).
Antibacterial rinse
3)
This function activates an antibacterial rinse at the
end of the wash cycle, guaranteeing a further
reduction of bacteria. Press the button to activate or
deactivate the function. This function can be used
with those programmes marked with the relative
symbol in table 1.1.
The dishwasher door must be kept shut for the
entire duration of the programme in order to
guarantee reduction of bacteria. If the door is
opened the indicator lamps starts flashing.
"Delayed start" button
Press the button repeatedly to delay the start of the
programme. Delay adjustable from 1 to 24 hours.
With successive touch of the button, the delay start
indicator increases by one hour and after 24 returns
to 00. Then press the start button. The dishwasher
will start at the set time.
Start button
Switches "on" when the dishwasher is operating.
Flashes when a fault occurs.
Switches off at the end of the programme.
Reset button - for changing
programme or failure display
Press this button to cancel a started programme and
selected options. Press this button to cancel the
main fault indicators (F. . ), for fault details consult
chapter "What to do if ...). A new programme can
then be selected and started.
Quick Reference Guide / Overview
5
Programme Chart
Detergent
dispenser
Consumption
1)
P
Programmes
Selectable
extra function
Loading instructions large small Litres kWh Min
1
Sensor + 40-70°C
Automatic programme
recommended for routine
washes, with dried-on food (for
example for EN 50242).
X X 7-17 0.99-1.75
65-
220 ±
1)
2
Pre-Rinse cold Crockery to be washed later. - - 4.0 0.03 14 ±
1)
3
Glass 40°C
Light soiling, for example glasses
and cups.
X - 10.0 0.85 100 ±
1)
4
Quickwash 40°C
Lightly soiled crockery with no
dried-on food.
X - 10.0 0.65 30 ±
1)
5
Eco
2)
50°C
Normally soiled crockery. Energy
saving programme with
prolonged drying cycle.
X X 11.0 1.05 170 ±
1)
6
Pro Clean
Very dirty dishes or stubborn
grime.
e.g. pots and pans.
X X 15.0-19.0 1.90-2.05
200-
220 ±
1)
7
Overnight
55°C
Normally soiled crockery, gentle
and quiet programme thanks to
the low spray pressure (39dbA).
X X 13.0 1.20 290 ±
1)
1) Programme data obtained in conformity with European standard EN 50242. The data may vary, according to different loads, different
extra functions, different sensor settings (for sensor programmes only), different water supply temperatures, different water
hardnesses, different power supply voltages, etc.
2) Reference programme for energy label in compliance with EN 50242 - Important Information for Test Laboratories: for detailed
information on the EN/Standard loading comparison test and other tests, contact the following address:
nk_customer@whirlpool.com.
3) The bacteria removal efficiency has been tested by the Institut Pasteur de Lille (France), based on the NF EN 13697 standard of
November 2001.
Quick Reference Guide
Table 1.1
Loading...