FRAMTID
HGA4K
HU
|
ENGLISH |
4 |
HU |
||
|
MAGYAR |
17 |
|
Language, Nyelv
Country, Ország
ENGLISH |
4 |
Table of contents
Safety information |
4 |
Injector table |
10 |
Product description |
6 |
Technical Data |
11 |
Daily use |
7 |
Installation |
11 |
Helpful hints and tips |
7 |
Environmental concerns |
14 |
Maintenance and cleaning |
8 |
IKEA GUARANTEE |
15 |
What to do if ... |
9 |
|
|
Safety Information
Your safety and the safety of others are very important.
This manual and the appliance itself provide important safety messages, to be read and observed at all times.
This is the safety alert symbol, pertaining to safety, which alerts users
to potential hazards to themselves and others.
All safety messages will follow the safety alert symbol and either the terms:
DANGER Indicates a hazardous situation which, if not avoided, will
cause serious injury.
WARNING Indicates a hazardous situation which, if not avoided, could
cause serious injury.
All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
The appliance must be disconnected from the power supply before carrying out any installation work.
Installation and maintenance must be carried out by a qualified technician, in
compliance with the manufacturer’s instructions and local safety regulations to the relevant gas standard. Only use original spare parts. Do not repair or replace any part of the appliance unless specifically stated in the user manual.
WARNING If the information in this manual is not followed exactly, a fire or
explosion may result causing property
damage or injury.
-- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance.
What to do if you smell gas:
-- Do not try to light any appliance. -- Do not touch any electrical switch.
-- Do not use any phone in your building. -- Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
-- If you cannot reach your gas supplier, call the fire department.
-- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
-- Use appliance in well ventilated rooms only.
-- The electrical and gas connections must comply with local regulations.
-- When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm, that provides full disconnection.
-- Regulations require that the appliance is grounded.
-- The power cable must be long enough for connecting the appliance, once fitted in its housing, to the power supply
-- Use only flexible or rigid metal hose for gas connection.
-- If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied
by manufacturer (type H05V2V2-F 90°C
ENGLISH |
5 |
or H05RR-F). This operation must be performed by a qualified electrician.
-- The manufacturer cannot be held responsible for any injury to persons or animals or damage to property
arising from failure to comply with these requirements.
-- Do not use multiple plug adapters or extension cords.
-- Do not pull the power supply cord in order to unplug the appliance.
-- The electrical components must not be accessible to the user after installation.
-- Do not touch the appliance with any wet part of the body and do not operate it when barefoot.
-- This hob (class 3) is designed solely for private household use for cooking food. Do not use this appliance as a
space heater to heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of the hob.
-- The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls.
-- The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or with lack of experience and knowledge of the appliance, unless supervised or previously instructed in its use by those responsible for their safety.
-- Young children should be kept away from the appliance and supervised to ensure that they do not play with it.
-- The use of a gas appliance produces heat and humidity in the room. Make sure the room is well-ventilated, or install an extractor hood with exhaust duct.
-- In case of prolonged use, additional ventilation may be necessary (by opening a window or increasing the hood extraction speed).
-- After use, make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve.
-- Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat, oil or alcohol (e.g. rum, cognac, wine).
-- Keep the packaging materials out of the reach of children.
-- Before cleaning or maintenance wait for hob to cool down.
Save these instructions
ENGLISH |
6 |
Product description
2
1
3 |
5 |
9
4 |
8 |
7
6
1Removable panstand grids
2Rapid burner
3Semi-rapid burners
4Semi-rapid burners
5Auxiliary burner
6Semi-rapid burner control knob
7Semi-rapid burner control knob
8Rapid burner control knob
9Auxiliary burner control knob
Symbols |
|
|
|
Solid disc |
Tap closed |
Large flame |
Maximum |
and star |
opening/delivery |
and electric |
|
|
ignition |
Small flame |
Minimum opening |
or reduced |
|
|
delivery |
ENGLISH
Daily use
Do not let the burner flame extend beyond the edge of the pan.
Important: when the hob is in use, the entire hob area may become hot.
-- To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting.
-- Press the knob against the control panel to ignite the burner.
-- After the burner has ignited, keep the knob pressed for about 5-10 seconds to allow proper device operation.
This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally (because of sudden draught, an interruption in the gas delivery, boiling over of liquids, etc.).
7
-- The knob must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not remain lit,
wait at least one minute before trying to light it again.
NOTE: should particular local conditions of the delivered gas make the ignition of burner difficult, it is advisable to repeat the operation with the knob turned to small flame setting.
The burner might go out when the knob is released. This means that the safety device has not warmed up enough. In this
case, repeat the operations described above.
Helpful hints and tips
This hob has burners of different diameters. For better burner performance, please stick to the following rules:
-- Use pots and pans with bottoms the same width as that of the burners or slightly larger (see table on the right).
-- Only use flat-bottomed pots and pans.
-- Use the correct amount of water for cooking foods and keep the pot covered.
-- Make sure pots on the grates do not protrude beyond the edge of the hob.
IMPORTANT: improper use of the grids can result in damage to the hob: do not position the grids upside down or slide them across the hob. Do not use:
-- Cast iron griddles, ollar stones, terracotta pots and pans.
-- Heat diffusers such as metal mesh, or any other types.
-- Two burners simultaneously for one receptacle (e.g. fish kettle).
Burner |
Pot Ø |
|
|
Rapid |
from 24 to 26 cm |
|
|
Semi-rapid |
from 16 to 24 cm |
|
|
Auxiliary |
from 8 to 14 cm |
|
|
ENGLISH
Maintenance and cleaning
Disconnect power before servicing. -- All the enamelled and glass parts
should be cleaned with warm water and neutral solution.
-- Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long. Any food spills (water, sauce, coffee, etc.) should be wiped away before they dry.
-- Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois. Remove baked-on dirt with specific cleaners for stainless steel surfaces.
NOTE: clean stainless steel only with soft cloth or sponge.
-- Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.
-- Do not use steam cleaning appliances. -- Do not use flammable products.
-- Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob.
CLEANING THE HOB PARTS
-- Grids, burner caps and burners can be removed to be cleaned.
-- Clean them by hand with warm water and non-abrasive detergent, removing any food residues and checking that none of the burner openings is clogged.
8
-- Rinse and dry
-- Refit burners and burner caps correctly in the respective housings.
-- When replacing the grids, make sure that the panstand area is aligned with the burner.
Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation.
Check these items frequently, and if necessary, clean them with a damp cloth. Any baked-on food should be removed with a toothpick or needle.
NOTE: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing.
ENGLISH |
9 |
What to do if ...
Problem |
Possible cause |
Solution |
The electric ignition does not |
There is no electrical |
Check the unit is plugged in |
work |
supply |
and the electrical supply is |
|
|
switched on. |
The burner fails to ignite |
The gas tap could be |
Check that the gas tap is |
|
closed |
open |
The gas ring burns unevenly |
Burner crown may |
Clean the burner crown |
|
be occluded by food |
according to cleaning |
|
residues |
instructions to make sure that |
|
|
the burner crown is clear of |
|
|
food residues. |
Before calling the After-Sales Service:
1.Check “Troubleshooting guide” to see if you can eliminate the problem yourself
2.Turn the hob on again to check if correct operation has been restored.
3.If the problem persists, contact the After-
sales Service.
Give the following information:
•type of fault;
•hob model;
•service number (i.e. the number after the word SERVICE on the dataplate under the hob and on the warranty certificate);
•your full address;
•your telephone number.
If any repairs are required, contact an authorised service centre, indicated in the warranty.
In the unlikely event that an operation or repair is carried out by an unauthorised technician, always request certification
of the work carried out and insist on the use of original spare parts.
Failure to comply with these instructions may compromise the safety and quality of the product.
ENGLISH |
10 |
Injector table
Category II2HS3B/P
Type of gas used |
Type of |
Injector |
Nominal |
Nominal |
|
Reduced |
|
Gas pressure |
|||||
|
burner |
marking |
heating |
consum- |
|
heat |
|
(mbar) |
|
||||
|
|
|
|
capacity |
ption |
|
capacity |
|
|
|
|
|
|
|
|
|
|
|
|
min. |
nom. |
max. |
|||||
|
|
|
|
kW |
|
|
|
kW |
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
||
NATURAL GAS |
Rapid |
Y 110 |
3.00 |
286 l/h |
|
0.70 |
|
|
|
|
|
||
Semi-rapid |
F3 87 |
1.65 |
157 l/h |
|
0.40 |
|
20 |
|
25 |
33 |
|||
(Methane) G20 |
|
|
|
||||||||||
Auxiliary |
X 68 |
1.00 |
95 l/h |
|
0.35 |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NATURAL GAS |
Rapid |
F2 125 |
3.00 |
332 l/h |
|
0.60 |
|
|
|
|
|
||
Semi-rapid |
F2 96 |
1.65 |
183 l/h |
|
0.35 |
|
18 |
|
25 |
33 |
|||
(Methane) G25.1 |
|
|
|
||||||||||
|
Auxiliary |
F1 71 |
1.00 |
111 l/h |
|
0.30 |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LIQUID |
Rapid |
85 |
|
3.00 |
218 g/h |
|
0.60 |
|
|
|
|
|
|
PETROLEUM |
|
|
|
|
|
|
|
||||||
Semi-rapid |
63 |
|
1.65 |
120 g/h |
|
0.35 |
|
25 |
|
30 |
35 |
||
GAS |
|
|
|
|
|||||||||
Auxiliary |
50 |
|
1.00 |
73 g/h |
|
0.30 |
|
|
|
|
|
||
(Cylinder) G30 |
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LIQUID |
Rapid |
85 |
|
3.00 |
218 g/h |
|
0.60 |
|
|
|
|
|
|
PETROLEUM |
|
|
|
|
|
|
|
||||||
Semi-rapid |
63 |
|
1.65 |
120 g/h |
|
0.35 |
|
25 |
|
30 |
25 |
||
GAS |
|
|
|
|
|||||||||
Auxiliary |
50 |
|
1.00 |
73 g/h |
|
0.30 |
|
|
|
|
|
||
(Cylinder) G31 |
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
||||||||
Type of gas |
Appliance |
|
Nominal heating |
Total nominal |
Air necessary |
||||||||
used |
model |
|
capacity kW |
|
consumption |
(m3) for |
|
||||||
|
|
|
|
|
|
|
|
|
combustion |
|
|||
|
|
|
|
|
|
|
|
|
1 m3 of gas |
|
|||
G20 25 mbar |
4 gas |
|
|
7.30 |
|
|
695 l/h |
|
|
9.52 |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
||
G30 30 mbar |
4 gas |
|
|
7.30 |
|
|
531 g/h |
|
|
30.95 |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
||
G31 30 mbar |
4 gas |
|
|
7.30 |
|
|
531 g/h |
|
|
30.95 |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
||
G25.1 25 mbar |
4 gas |
|
|
7.30 |
|
|
809 l/h |
|
|
8.187 |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Electric Power: 230 V ~ 50 Hz
ENGLISH |
11 |
Technical data
Dimensions |
|
Width (mm) |
590 |
Height (mm) |
40 |
Length (mm) |
510 |
Voltage (V) |
230 |
The technical information are situated in the rating plate on the bottom side of the appliance.
Installation
After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest After-sales Service.
Technical information for the installer
-- This product can be embedded in a worktop 20 to 50 mm thick.
-- If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must be positioned in no case less than 20 mm from the bottom of the hob.
-- Before installation, make sure that:
-- the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table);
-- the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;
-- This appliance is not connected to a
fume exhaust device. It shall be installed in accordance with current installation regulations. Particular attention shall be given to the relevant requirement regarding ventilation.
-- Combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans.
Gas connection
This operation must be performed by a qualified technician.
The gas supply system must comply with local regulations to the relavant gas standard.
-- You can find specific local regulations for some countries in the paragraph
-- “Reference to Local Regulations”. If no information concerning your Country is given, please ask details to a qualified technician.
-- The connection of the hob to the gas pipe network or gas cylinder must be