Whirlpool GZ7930XHS1, GZ7936XHS1, KIRD862HSS1, KIRD802HSS1 Owner’s Manual

iMPORTANT:
Read and save

these instructions.

iMPORTANT:

Installer: Leave Installation instructions with

the homeowner.

Homeowner: Keep Installation instructions for
future reference.

Save Installation Instructions for local electrical
inspector'suse.

Part No. 4329225/9763381

Quick Reference

Table of Contents:

Pages

[] Before you start
[] Electrical requirements

[] Product dimensions
[] Cabinet dimensions
[] Countertop cutout dimensions

[] Vent system requirements

Interior-mounted vent motor

[_- [] installation steps

[] Vent system requirements

Exterior-mounted vent motor

[_-[_ Installation steps

[] Use and Care information
[] Accessories

Yoursafety and the safety of

others are very important.

We have provided many important

safety messages in this manual

and on your appliance. Always

read and obey all safety
messages.

This is the safety alert

symbol.

This symbol alerts you to
potential hazards that can kill or
hurt you and others.

All safety messages will follow the

safety alert symbol and either the

word "DANGER" or "WARNING".
These words mean:

You can be killed or seriously

injured if you don't immediately

follow instructions.

You can be killed or seriously

injured if you don't follow
instructions.

All safety messages will tell you
what the potential hazard is, tell you

how to reduce the chance of injury,

and tell you what can happen if the

instructionsare not followed.

IMPORTANT: Observe all governing
codes and ordinances.

Failure to meet codes and
ordinances could lead to fire or
electrical shock.

Proper installation is your
responsibility. Make sure you have

everything necessary for correct
installation. It is the responsibility
of the installer to comply with the
installation clearances specified on

the model/serial rating plate.The
model/serial rating plate is located
on the front of the downdraft vent

above the wiring box cover.
Check location where downdraft

vent will be installed.The location
should be away from strong draft

areas, such as windows, doors and
strong heating vents or fans.
Before making countertop cutout,

check that downdraft vent and
cooktop location will clear cabinet

walls, backsplash, and rear wall

studs inside cabinet.

Mobile home installation

The installation of this downdraft
vent system must conform to the

Manufactured Home Construction
Safety Standards, Title 24 CFR,

Part 328 (formerly the Federal
Standard for Mobile Home

Construction and Safety, Title 24,
HUD, Part 280) or when such

standard is not applicable, the
Standard for Manufactured Home

Installation 1982 (Manufactured
Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*,
or latest edition, or with local
codes.

All openings in the wall or floor
where retractable downdraft vent

is to be installed must be sealed.
Electrical ground is required. See

"Electrical requirements:' page 3.

When installing downdraft vent,
the cabinet drawer will need to be

removed and the drawer front
installed permanently to cabinet.

NOTE: Downdraft vent is installed
directly behind the cooktop. Install

downdraft vent first.
Cabinet construction: Downdraft

vent is designed for use in a

cabinet with a depth of 24"
(61 cm). Some installations

require a countertop deeper than
25" (63.5 cm). See chart on page 5.

The maximum depth of the

overhead cabinet is 13" (33 cm).
Overhead cabinets installed at

either side of the downdraft vent
must be 18" (45.7 cm) above the
cooking surface.

See cooktop Installation
Instructions before making any

cutouts and for the minimum
distance between the front edge

of the countertop and front edge
of cooktop.The minimum

horizontal distance between the
overhead cabinets is the same as

the width of the installed

downdraft vent.

When installing a 36" (91.4 cm)

retractable downdraft vent with
"Create-A-Cooktop" modules, the

optional support must be installed
on the front of the downdraft vent.

See installation steps for details.

Parts supplied

for installation:

® 1 top trim

2 end caps

2 lower support legs
®2 overcounter support brackets
e 2 undercounter mounting brackets
® 1 bag of fasteners

® 1 metal cover

1 backdraft damper
® literature package
e optional support and two screws

(36" (91.4 cm) models only

Partsneeded

for installation:

®2 U.L.- or C.S.A.-listed 1/2" (12.7 ram)

conduit connectors (3 are required if
the exterior-mounted vent motor

is used.)

* 1wall cap for interior-mounted

motor

®vent system

power supply cable

wiring cable for optional remote
blower kit.

Toolsneeded for

installation:

e safety glasses
e gloves

jig or keyhole saw

,'drill with 1/8" drill bit
o pencil

® measuring tape

,'flat-blade screwdriver

Phillips screwdriver

e 3/8" (9.5 ram) nut driver or ratchet

e level

® pliers
® metal snips

®wire stripper or utility knife
®caulking gun and weatherproof caulk
e duct tape

IMPORTANT: Observe all
governing codes and ordinances.

It is the customer's responsibility:

eTo contact a qualified electrical

installer.

• To assure that the electrical
installation is adequate and in

conformance with National
Electrical Code, ANSI/NFPA 70

-- latest edition*, or CSA
Standards C22.1-g4, Canadian

Electrical Code, Part 1 and
C22.2 No. 0-M91 - latest

edition** and all local codes
and ordinances.

If codes permit and a separate
ground wire is used, it is

recommended that a qualified
electrician determine that the

ground path is adequate.
Do not ground to a gas pipe.

Check with a qualified electrician if
you are not sure downdraft vent is
properly grounded.

Do not have a fuse in the neutral
or ground circuit.

IMPORTANT: Save installation
instructions for electrical

inspector's use.

AB A 120-volt, 60-Hz, AC-only,
fused electrical supply is required

on a separate 15 amp circuit. A
time-delay fuse or circuit breaker

is recommended.The fuse must
be sized per local codes in

accordance with the electrical
rating of the downdraft vent as

specified on the model/serial
rating plate located on the front

of the downdraft vent above the

wiring box cover.

B_ The downdraft vent must

be connected with copper wire
only.

C_ Wire sizes and connections
must conform to the
requirements of the National

Electrical Code, ANSI/NFPA 70 --
latest edition*, or CSA Standards
C22.1-94, Canadian Electrical
Code, Part 1 and C22.2 No. 0-M91

- latest edition** and all local
codes and ordinances.

WARNING -- TO REDUCE THE

RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO

PERSONS, OBSERVE THE
FOLLOWING:

installation work and electrical

wiring must be done by qualified
person(s) in accordance with all

applicable Codes and Standards,
including fire related construction.

Sufficient air is needed for proper
combustion and exhausting of

gases through the flue (chimney)
of fuel burning equipment to

prevent back drafting. Follow the
heating equipment

manufacturer's guideline and
safety standards such as those

published by the National Fire

Protection Association

(NFPA),and the American Society
of Heating Refrigeration and Air

Conditioning Engineers
(ASHRAE), and the local code

authorities.
When cutting or drilling into wall

or ceiling, do not damage
electrical wiring and other hidden
utilities.

Ducted fans must always be

vented to the outdoors.
WARNING --To reduce the risk

of fire, use only metal ductwork.
This unit must be grounded.

This downdraft vent should

be connected directly to the fused
disconnect (or circuit breaker)

through flexible, armored or non-
metallic sheathed, copper cable.

Allow some slack in the cable so
the downdraft vent can be moved

if servicing is ever necessary.

E., A U.L.- or C.S.A,-listed, 1/2"

(12.7 mm) conduit connector
must be provided at each end of

the power supply cable (at the

downdraft vent and at the

junction box).

Awiring diagram is located

on the downdraft vent base
above the wiring box cover.

Copies of the standards listed may be
obtained from:

* National Fire Protection Association

One Batterymarch Park
Quincy, Massachusetts 02269

**CSA International

8501 East PleasantValley Road
Cleveland, Ohio 44131-5575

\ (15.9mm)

5/8

16"

(40.6cm) /

INTERNAL "_./_ 2-1/8"

BLOWER 9-3/8" _ _ 64 cm

MOTOR (23.8 cm)

9" (22.9 cm) Dia.

NOTE: A 10" (2.5
cm) round vent
system adapter

collar attaches over
this hole. Adapter

collar is supplied
with exterior

blower.

4 u

(10.2 cm)

6/8"
(15.9 mm)

(20,8"cm)

16" '_r_

40.6 cm ,_

EXTERIOR-MOUNTED

BLOWER MOTOR

A = 1/2" (12.7 mm)

mln.

all cutouts are for
3-1/4" x 10"

(8.3 cmx 25.4 cm)

vent system

Locate power supply
junction box at lower
right hand rear corner of

cabinet.

17-3/16"
(43.7 cm)

(10.5 cm)

See cooktop manufacturer's
instructions for cooktop cutout
depth and width.

Use dimensions for vent system
cutout location that applies to
your installation.

17-9/16"
(44.6 cm)

Vent system cutout dimensions for internal
blower models only.

Exterior mounted blower systems connect
with 10" (25.4 cm) round vent.The cutout
locations for this vent system will depend
upon your specific installation.

centerline of
cooktop cutout

27-1/2"(69.9cm)for30"(76.2cm)vent
33-1/2"(86.1cm)for36"(91.4cm)vent

\

\

A = 1/2" cooktop

(12.7 ram) Xmin.

-,_. Some models require a
countertop deeper than

25" (63.5 cm); see cutout
dimensions chart below.

1-7/8"

(4.8 cm)

1/4"

(6.4 mm)

1/2"
(12.7 ram)

min.

backsplash

See cutout
dimensions
chart below.

It is recommended that the cooktop
and vent cutouts be drawn on the

countertop before making any
cutouts to avoid mistakes.

See Cooktop Installation Instructions
for complete cutout dimensions,
location dimensions and installation

details.

IMPORTANT." Countertops with a
bullnosed front edge are not

recommended for these installations.
Use only the exterior-mounted

blower system, KPEC992M

[900 cfm (25.5 m3/m)], with the

retractable popup downdraft vent
system.

Co0kt0p

C00kt0pModels Size

KGCS105G 30"

(76.2cm',
KECC502G* KECC507G* 30"
KECO507K* KECO508G*(76:2cm',

KECC508M*
KECS100G* 30,

(76.2cm',
GLT3014G GLT3034L 30,
SCS3004G SO83004L (762 em',

SOS3014G SOS3014L
RCO3024G* RCO3024L* 30'!

GJC3034G* GJC3034L* (76.2cm'
RCS3004G* RCS3014L* 301'

RCS3014G* RCS3014L* (76,2cm',
YROS3014G*YROS3014L

centerline of

cooktop cutout

3/4" (19.1 ram) max.
backsplash depth

1/2" (12.7 mm) \4 k

minimum to

splashguard or

rear wall

H

Required rain.

countertop depth

Installedwith

VentSystem Models

KIRD801HSS KIRDS02HSS

KIRD801HSS KIRDS02HSS

KIRD801HSS KIRDS02HSS

GZ7730XGS GZ7930XGS
GZ7930XHS

GZ7730XGS GZ7930XGS
GZ7930XHS

GZ7730XGS GZ7930XGS
GZ7930XHS

A B C

29" 27-1/2" 19-5_"

(73.7cm) (69.9cm) (49.8cm)

29-1_" 27-1/2" 20-1_"

(74.9cm) (69.9cm) (52.1cm)

28-7/8" 27-1/2" 19"

(73.3cm) (69.9cm) (48.3cm)

29" 27-1/2" 19-5/8"

(73.7cm) (69.9cm) (49.8cm)

29-1/2" 27-1/2" 20-1/2"

(74.9cm) (69.9cm) (52.1cm)

28-7/8" 27-1/2" 19"

(73.3cm) (69.9cm) (48.3cm)

countertop

downdraff

vent

D

2-1/8"

(5.4cm)

2-1/8"

(5.4cm)

2-1/2"

(6.4cm)

2-1/8"

(5.4cm)

2"

(5.1cm)

2-1/2"

(6.4cm)

J

1/4"
(6.4 mm)

--_J 1-,_-_I/2"!12.7mm)

Overall depth of cooktop

_of cooktop and

downdraft vent system

E

1-3/4"

(4.4 cm)

2"

(5.1 cm)

3-3/8"

(8.6 cm)

1-3/4"

(4.4 cm)

(5.1 cm)

3 _

(7.6 cm)

F G H

31-_8" 23" 25"

(79.7cm) (58.4cm) (63.5cm)

31-1/2" 23-1/4" 25-_8"

(80.0cm) (59.1cm) (65.7cm)

31-1/2" 23" 25-5/8"

(80.0cm) (58.4cm) (65.1cm)

31-3/8" 23" 25"

(79.7cm) (58.4cm) (63.5cm

30" 23" 25-3/4"

(76.2cm) (58.4cm) (65.4cm)

31-1/2" 23" 25-1/2"

(80.0cm) (58.4cm) (64.8cm)

minimum

and downdraft vent

system

G

KGCS166G 36" KIRD861HSS KIRD862HSS 35-1/4" 33-1/2 19-5/8"

(91.4cm', (89.5cm) (85.9cm) (49.8cm)
KECC562G* KECC567G* 36, KIRD861HSS KIRD862HSS 35-1/2" 33-1/2" 20-1/2"

KECO568G* (91i4cm' (90.2cm) (85.9cm) (52.1cm)
KECS161G* 36, KIRD861HSS KIRD862HSS 35" 33-1/2" 19"

(91i4cm' (88.9cm) (85.9cm) (48.3cm)
GLT3614XG 36" GZ7736XGS GZ7936XGS 35-1/4" 39-1/2" 19-5/8"
GLT3634XL (91.4cm', GZ7936XHS (89.5cm) (85.9cm) (49.8cm)

GJC3634G* 36, GZ7736XGS GZ7936XGS 35-1/2" 33-1/2" 20-1/2"
GJO3634L* (91.4cm', GZ7936XHS (90.2cm) (85.9cm) (52.1cm)
RCS3614G* 36, GZ7736XGS GZ7936XGS 35" 33-1/2" 19"
ROS3614L* (91.4cm' GZ7936XHS (88.9cm) (85.9cm) (48.3cm)

* Installationwith ventsystem requiresc0untert0pandbase cabinetdeeperthan standard25"(63.5 cm)

2-1/8" 1-3/4" 37-1/2" 23" 25"

(5.4cm) (4.4 cm) (95.3cm) (58.4 cm) (63.5 cm)

2-1/8" 2" 37-1/2" 23-1/4" 26-7/8"

(5.4cm) (5.1 cm) (95.3cm) (59.1 cm) (68.3 cm)

2-1/2" 3-3/8" 37-5/8" 23" 25-5/8"

(6.4cm) (8.6 cm) (95.6cm) (58.4 cm) (65.1 cm)

2-1/8" 1-3/4" 36-5/8" 23" 25"

(5.4cm) (4.4 cm) (93.0cm) (58.4 cm) (63.5 cm)

2" 2" 36" 23" 25-3/4"

(5.1cm) (5.1 cm) (91.4cm) (58.4 cm) (65.4 cm)

2-1/2" 3" 37-5/8" 23" 25-5/8"

(6.4cm) (7.6 cm) (95.6cm) (58.4 cm) (65.1 cm)

deepc0untert0pand 24" (61.0cm) deepbasecabinet.