Whirlpool GY397LXUB, GY399LXUS, GY399LXUT, GY399LXUQ, GY399LXUB Dimension Guide

®

30" Slide-in Electric Range

PRODUCT MODEL NUMBERS OVERALL DIMENSIONS

CABINET OPENING DIMENSIONS

COUNTERTOP PREPERATION

GY397LXU
GY399LXU

Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.

Electrical: This range is manufactured with the
neutral terminal connected to the cabinet. Use a 3­wire, UL listed, 40- or 50-amp power supply cord
(pigtail) (see Range Rating chart below). If local
codes do not permit ground through the neutral,
use a 4-wire power supply cord rated at 250 volts,
40- or 50-amps and investigaed for use with
ranges. A time-delay fuse or circuit breaker is
recommended. The model/serial rating plate is
located on the oven frame behind the storage
drawer panel.

Ref. 8101P750-60

04-09-08

The cooktop sides of the slide-in range fit over the cutout
edge of your countertop.

If you have a square finish (flat) countertop and the
opening width is 30" (76.2 cm), no countertop
preparation is required.

Formed front-edged countertops: Must have molded edge
shaved flat 3/8" (1.0 cm) from each front corner of
opening.

Tile countertops may need trim cut back 3/8" (1.0 cm)
from each front corner and/or rounded edge flattened.

If countertop opening width is greater than
30" (76.2 cm), adjust the 3/8" (1.0 cm) dimension.

Countertop must be level. Place level on countertop, first
side to side; then front to back. If countertop is not level,
range will not be level. Oven must be level for
satisfactory baking conditions.

28-5/16"
(71.9 cm)
depth with
handle

35-3/4" (90.8 cm)
cooktop height
with leveling
legs screwed all
the way in

23-3/4"
(60.3 cm)

1" (2.5 cm)
spacer

30-3/4" (78.1 cm)
cooktop width

29-7/8" (75.9 cm) width*

Cabinet opening dimensions
shown are for:

25" (63.5 cm) countertop
depth, 24" (61.0 cm) base
cabinet depth, 36" (91.4 cm)
countertop height

junction box – 5.5" (14 cm min.)
from either cabinet, 10" (25.4 cm)
max. from floor.

23-1/4" (59.1 cm)
opening depth

30" (76.2 cm) min.
cabinet opening width

3/8" (9.5 cm)
radius both
corners

For minimum
clearance to the
top of the cooktop,
see NOTE.*

13" (33.0 cm) max.
upper cabinet depth

30" (76.2 cm)
opening width**

Cabinet door or
hinge should not
extend into cutout.

*

NOTE:

24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than 1/4" (6.4 mm)

flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,

0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) min. clearance between the top of the
cooking platform and the bottom of an unprotected wood or metal cabinet.

**30-7/8" (78.4 cm) with side panels.

Formed or tiled countertop
trimmed 1/2" (1.3 cm) back
at front corners of
countertop opening.

30-3/4" (78.1 cm)

3/8"
(1.0 cm)

30"
(76.2 cm)
opening
width

Range Rating Specified Rating

of Power Supply
Cord Kit and
Circuit
Protection

120/240 Volts 120/208 Volts Amps

8.8 - 16.5 KW 7.8 - 12.5 KW 40 or 50

16.6 - 22.5 KW 12.6 - 18.5 KW 50

*30-3/4" (78.1 cm) with side panels