Whirlpool GU3600XTVY0, GU3600XTVY1, GU3600XTVY2, GU3600XTVT0, GU3600XTVS0 Installation Guide

...

Installation instructions

Undercounter _hwasher

instructions d'installation

Lave-vaisselle encastre

Table of Contents ............................................................................. 2

Table des matieres ......................................................................... 17

W10021230

Table of Contents

Dishwasher Safety ................................. 2

Installation Requirements ........................... 3

Tools and parts ................................. 3

Location Requirements .......................... 3

Drain Requirements ............................. 5

Water Supply Requirements ...................... 5

Electrical Requirements .......................... 5

installation Instructions ............................. 6

Prepare cabinet opening

using existing utility hookups ..................... 6

Prepare cabinet opening

where there are no existing utility hookups .......... 7

Prepare dishwasher ............................. 9

Make electrical connection ...................... 12

Connect to water supply ........................ 13

Connect to drain ............................... 14

Secure dishwasher in cabinet opening ............. 14

Dishwasher Safety

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door. Doing so can result in serious injury or cuts.

You need to:

Slowly open dishwasher door while someone grasps the rear of the dishwasher. Remove shipping materials, drain

hose and lower rack. Close dishwasher door until latched. Observe all governing codes and ordinances. Install this dishwasher as specified in these instructions.

Installation should be performed by a qualified service

technician.The dishwasher must be installed to meet all

electrical and plumbing national and local codes and ordinances.

Installation Requirements

Location Requirements

Tools and Parts

Gather the required tools and parts before starting

installation.

All installations

Tools needed: o pliers

+ Phillips screwdriver

5/16" and 1/4" nut drivers or hex sockets

®measuring tape or ruler e 10" adjustable wrench that

opens to 1-1/8" (2.9 cm)

+ flat-blade screwdriver ®utility knife

®2 twist-on wire connectors

which are the proper size

to connect your household

wiring to 16-gauge wiring in dishwasher

small level

in addition, for new installations

Tools needed: Parts needed:

®electric drill with 1/2", 3/4"

and 1-1/2" hole saw bits

e small tubing cutter e wire stripper

®1-1/2"-2" screw-type clamp

if connecting to waste-tee

Parts supplied

A. 2 - drain hose clamps, 1 large and 1 small B. 2 - # 10 x 1/2" Phillips-head screws C. drain hose

flashlight

shallow pan +5/8" open-end wrench ®bath towel +wood block

Parts needed: +90° elbow with 3/8" N.RT.

external threads on one

end. (The other end must

fit your water supply line.) ®Teflon _ tape or pipe joint

compound

shims (if installed with

built-up floor)

, copper tubing (3/8"

recommended) or flexible stainless steel braided fill

line clamp connector or

conduit connector to fit a 7/8" (2.2 cm) diameter hole

Do not run drain lines, water lines or electrical wiring

where they can interfere with or contact dishwasher motor

or legs.

The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor should not touch the floor.

Do not install dishwasher over carpeted flooring. Protect dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by

the warranty. A side panel kit is available from your dealer for installing

your dishwasher at the end of your cabinetry. A moisture barrier accessory (Part No. 4396277) is available

from your dealer for installing underneath the countertop,

but is not required. Check location where dishwasher will be installed.The

location must provide:

o easy access to water, electricity and drain.

convenient access for loading and unloading dishes. Corner locations require a 2" (5.1 cm) minimum clearance

between the side of the dishwasher door and the wall or

cabinet.

, square opening for proper operation and appearance. o cabinet front perpendicular to floor.

. level floor. (If floor at front of opening is not level with

floor at rear of opening, shims may be needed to level dishwasher.)

NOTE:To prevent shifting during dishwasher operation, shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it

winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area shown in the "Cutout dimensions" section.

HelpfulTip: If the floor in the dishwasher opening is uneven (example: tile flooring only partway into opening) you will need to take special care in measuring dimensions and in leveling dishwasher.

Make sure all these parts are included. See separate parts list for accessories available for your

dishwasher.

_YTeflon is a registered trademark of E.I. Du Pont de Nemours and

Company.

Product dimensions

Cutout dimensions

3/4" (1.8 cm) _.

insulation -

may be

compressed

(not used on all

models)

-,_-_ 25" (63.5 cm)

-_----21" {53.3 cm}--_

SIDE VIEW

Ill I (86cm) rain.

IH I with wheels

33-7/8"

,4" (61 cm)**

All surfaces must be free

from intrusions

_"" 24" (61cm)

min."--_

(5.1 cm) 10"

3-1/4"

(7 cm) (8.3 cm) (8.3 cm) (7 cm)

Cut holes in shaded area of cabinet walls or floor as specified below:

water line- 1/2" (1.3 cm)

drain line- 1-1/2" (3.8 cm) direct wire - 3/4" (1.9 cm) power supply cord - 1-1/2" (3.8 cm)

(25.4

94"

(86.4 cm)

rnin. _

REAR VIEW

r' Measured from the lowest point on the underside of countertop. May be

reduced to 33-7/8" (86 cm) by removing wheels from dishwasher.

_ Minimum, measured from narrowest point of opening.

_ May be increased to 6-5/8" (16.6 cm) if height of opening is 34-1/2"

(876 cm) at its lowest point.

Drain Requirements

Electrical Requirements

. Use the new drain hose supplied with your dishwasher.

If this is not long enough, use a new drain hose with a maximum length of 12 feet (3.7 m) that meets all

current AHAM/IAPMO test standards, is resistant to

heat and detergent, and fits the 1" (2.5 cm) drain

connector of the dishwasher.

o Connect drain hose to waste tee or disposer inlet

above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor. It is recommended that the

drain hose either be looped up and securely fastened

to the underside of the counter, or be connected to an

air gap.

c_ _ air gap

o Use an air gap if the drain hose is connected to house

plumbing lower than 20" (50.8 cm) above subfloor or

floor.

o Use 1/2" minimum I.D. drain line fittings.

Water Supply Requirements

_A hot water line with 20-120 psi (138-862 kPa) water

pressure.

o 120OF (49oC) water at dishwasher. o 3/8" O.D. copper tubing with compression fitting or

flexible stainless steel braided fill line (1/2" minimum

plastic tubing is not recommended).

_A 90 ° elbow with 3/8" N.RT. external pipe threads on

one end.

Do not solder within 6" (15.2 cm) from water inlet valve.

Contact a qualified electrician.

Assure that the electrical installation is adequate and in conformance with all national and local codes and

ordinances.

You must have:

+ 120-volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical

supply.

+ Copper wire only.

We recommend:

®A time-delay fuse or circuit breaker. eA separate circuit.

If direct wiring dishwasher:

o Use flexible, armored or non-metallic sheathed, copper

wire with grounding wire that meets the wiring

requirements for your home and local codes and

ordinances.

o Use strain relief method provided with house wiring

junction box or install a U.L.-listed/CSA-certified clamp connector to the house wiring junction box. If using conduit, use a U.L.-listed/CSA-certified conduit connector.

If connecting dishwasher with a power supply cord:

" Use Power Supply Cord Kit (Part No. 4317824) marked for

use with dishwashers. Kit contents include:

-Volex, Inc., UL listed 16 gauge 3 wire power supply cord with 3 prong grounded plug.

- Neer C-500 7/8 inch strain relief.

- 3 wire connectors.

- Part No. 302797 grommet

Follow the kit instructions for installing the power

supply cord.

o Power supply cord must plug into a mating three prong,

grounded outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and

ordinances.

installation instructions

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Turn off water supply.

install the drain hose

IMPORTANT: Always use a new drain hose even when installing a new replacement dishwasher.

1. Drill a 1-1/2" (3.8 cm) diameter hole in cabinet wall or floor on the side of the opening closest to the sink.

2, Connect drain hose to waste tee or waste disposer

using one of the following methods:

Option 1, Waste disposer - with air gap Option 2, No waste disposer- with air gap

Option 3, Waste disposer - no air gap* Option 4, No waste disposer- no air gap*

%nair gapisrecommended

Prepare cabinet opening using

existing utility hookups

e Follow the steps in this section if you are installing the

dishwasher in an existing cabinet opening with utility hookups.

e If you are installing the dishwasher in a cabinet opening

that does not have hookups, follow the steps under

"Prepare cabinet opening where there are no existing utility hookups" section.

1. wherefrontCheckiinereachesleftthatthe°fwatertheopeningtOwaterthe water ........................ direct

connection will be I[ I,ne !_ wire

made.

2. Check that the direct J

front right of opening 6"(16.2 c __

wire reaches to the ______ L____;_ where the electrical

connection will be made.

If the water line and the direct wire reach far enough into the opening, proceed to the next section "Install the drain hose:' If they do not reach far enough, follow the steps under "Prepare cabinet opening where there are no existing utility hookups:'

HelpfuITip:To reduce the vibration of the hose, keep

the hose away from the floor and the edge of the hole

where it passes through the cabinet.

Option 1, Waste disposer - with air gap:

1. Remove the disposer knockout plug. Cut end of drain hose if needed (do not cut ribbed section).

2. Attach drain hose to air gap with large spring-type clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*.

3. Use a rubber hose connector* with spring or screw-

type clamps* to connect air gap to disposer inlet.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher

will be installed.

drain hose - cut hereif needed

rubberhose connector

./air gap

spring-type clamp

drain trap

4. Insert drain hose

through hole cut in

cabinet to the front center of opening where

drain connection will be made.

r' Parts available from local plumbing supply stores

hose

drain hose

Option 2, No waste disposer - with air gap:

1. Cut end of drain hose if needed (do not cut ribbed section).

2. Attach drain hose to air gap with large spring-type clamp. If the drain hose was cut, use a 1-1/2" to 2"

(3.8 to 5 cm) screw-type clamp s,

3. Use a rubber hose connector* with spring or screw- type clamps* to connect air gap to waste tee.

This connection must be before the drain trap and at

least 20" (50.8 cm) above the floor where dishwasher

will be installed.

drain hose-

_cut here if needed

rubber hose

connector

Option 4, No waste disposer - no air gap:

1. Cut end of drain hose if needed (do not cut ribbed section).

2. Attach drain hose to waste tee with 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp s.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed. It is recommended that the drain hose

be looped up and securely fastened to the underside of

the counter.

drain hose -

_ cut here if needed

__ screw-type clamp

large spring-type

waste

drain trap hose

4. Insert drain hose

tee drain

drain hose

through hole cut in cabinet to the front

center of opening where drain connection will be

made.

r' Parts available from local plumbing supply stores

Option 3, Waste disposer - no air gap:

1. Remove the disposer knockout plug. Do not cut end of drain hose.

2. Attach drain hose to disposer inlet with large spring- type clamp.

This connection must be before the drain trap and at

least 20" (50.8 cm) above the floor where dishwasher

will be installed. It is recommended that the drain hose

be looped up and securely fastened to the underside of

the counter.

large spring-type clamp

drain hose

disposer inlet

drain trap

3. Insert drain hose

drain hose

through hole cut in cabinet to the front

center of opening where drain connection will be

made.

waste [ "_ "_ tee ' [_ I _

I I drain

kJ ] _ _ hose

dra,n trap JII

3. Insert drain hose

through hole cut in

cabinet to the front center of opening where

drain connection will be made.

r' Parts available from local plumbing supply stores

Prepare cabinet opening where there are no existing utility hookups

Electrical connection

Option1, Direct wire method:

HelpfulTip: Wiring the dishwasher will be easier if you route wire into the cabinet opening from the right side.

1. Drill a 3/4" (1.9 cm) optional preferred hole in right-hand locations locations

cabinet side, rear or floor. Preferred and

optional locations are shown.

2. Wood cabinet: Sand hole until smooth.

Metal cabinet: Cover hole with grommet, not provided.

Run wire into house wiring junction box.

Install a U.L-listed/CSA-certified clamp connector (strain relief) for flexible-type wire. If installing conduit,

attach a U.L.-listed/CSA-certified conduit connector to

the junction box.

Run other end of wire

through cabinet hole.

Cable must extend to the right front of cabinet

opening.

drain hose

Option2, Powersupplycord method:

NOTE: A mating, three prong, ground-type wall receptacle is required in a cabinet next to the dishwasher opening.

1. Drill a 1-1/2"

(3.8 cm) hole in optional preferred I

the cabinet rear .... locations locations ....

and optional L'.'::'J b i::::'J

Iocat ions are

shown. or side. Preferred [_

2. Woodcabinet: Sandholeuntil

smooth.

Metal cabinet: Cover hole with grommet (Part No.

302797) included with power supply cord kit.

install the water line

HelpfulTip: Routing the water line through the left side

of cabinet opening will make water connection easier.

Drill a minimum 1/2" (1.3 cm) hole in the cabinet side, rear or floor. Preferred and optional locations are

shown.

preferred locations

optional locations

2. Connect drain hose to waste tee or waste disposer using one of the following methods:

, Option 1, Waste disposer- with air gap , Option 2, No waste disposer- with air gap

, Option 3, Waste disposer- no air gap* , Option 4, No waste disposer- no air gap*

_'anair gapis recommended

HelpfulTip:To reduce the vibration of the hose, keep

the hose away from the floor and the edge of the hole

where it passes through the cabinet.

Option 1, Waste disposer - with air gap:

1. Remove the disposer knockout plug. Cut end of drain hose if needed (do not cut ribbed section).

2. Attach drain hose to air gap with large spring-type clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*.

3. Use a rubber hose connector* with spring or screw-

type clamps* to connect air gap to disposer inlet.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed.

drain hose - cut here if needed

rubber hose connector

gap

2. Measure overall length of copper tubing

copper tubing

required.

3. Attach copper tubing to the water line with a

manual shutoff valve.

4. Slowly feed copper tubing through hole in cabinet. Copper tubing will bend and kink easily, so be

gentle.The copper tubing should be far enough into the cabinet opening to connect it to dishwasher inlet on the

front left of the dishwasher.

5. Turn water shutoff valve to "ON" position. Flush water

into a shallow pan to get rid of particles that may clog

the inlet valve.

6. Turn shutoff valve to "OFF" position.

install the drain hose

IMPORTANT: Always use a new drain hose.

1. Drill a 1-1/2" (3.8 cm) diameter hole in

cabinet wall or floor on the side of the opening

closest to the sink.

drain trap

4. Insert drain hose through hole cut in

cabinet to the front center of opening where

drain connection will be made.

_'Parts available from local plumbing supply stores

spring-type clamp

hose

drain hose

Option 2, No waste disposer - with air gap:

1. Cut end of drain hose if needed (do not cut ribbed section).

2. Attach drain hose to air gap with large spring-type clamp. If the drain hose was cut, use a 1-1/2" to 2"

(3.8 to 5 cm) screw-type clamp s,

3. Use a rubber hose connector* with spring or screw- type clamps* to connect air gap to waste tee.

This connection must be before the drain trap and at

least 20" (50.8 cm) above the floor where dishwasher

will be installed.

drain hose- cut here if needed

rubber hose

connector

large spring-type

Option 4, No waste disposer - no air gap:

1. Cut end of drain hose if needed (do not cut ribbed section).

2. Attach drain hose to waste tee with 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp s.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed. It is recommended that the drain hose

be looped up and securely fastened to the underside of

the counter.

drain hose -

_ cut here if needed

_ screw-type clamp

_easte/ __ _ra_n

waste

drain trap hose

4. Insert drain hose

tee drain

drain hose

through hole cut in cabinet to the front

center of opening where drain connection will be

made.

_' Parts available from local plumbing supply stores

Option 3, Waste disposer - no air gap:

1. Remove the disposer knockout plug. Do not cut end of drain hose.

2. Attach drain hose to disposer inlet with large spring- type clamp.

This connection must be before the drain trap and at

least 20" (50.8 cm) above the floor where dishwasher

will be installed. It is recommended that the drain hose

be looped up and securely fastened to the underside of

the counter.

large spring-type clamp

drain hose

dra,ntrap:--111

3. Insert drain hose

through hole cut in

cabinet to the front center of opening where

drain connection will be made.

Parts available from local plumbing supply stores

Prepare dishwasher

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Doing so can result in serious injury or cuts.

drain hose

drain trap

3. Insert drain hose through hole cut in

cabinet to the front center of opening where

drain connection will be

made.

disposer inlet

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

drain hose

Put corner posts from packaging behind dishwasher. Grasp sides of dishwasher door frame and put dishwasher on its back, resting on top of the corner

posts.

2. Removetwoscrewsattachingaccesspanelandlower

paneltodishwasherusinga 1/4" hex socket, nut driver

or Phillips screwdriver.

3. Remove panels and set panels aside on a protective surface.

4. Check that grounding clip is attached to the lower

panel.

8. Measure height of cabinet opening from underside of countertop to

floor where dishwasher will be installed (you need the lowest

point). Check chart for that height opening. Put wheels in the required

position.

Minimum Wheel

cutout height position front leg

34" (86.4 cm) 1 10 34-1/4" (87 cm) 2 5

wheel

3 34-1/2" (87.6 cm) 3 0

Number of

turns on

lower panel

clip

water inlet valve

5. ApplyTeflon _: tape or pipe joint compound to 90 ° elbow fitting and connect fitting to

water inlet valve.

6. Tighten elbow until snug, and

be sure that it faces to the

rear.

7. Remove terminal box cover..

- If you are direct wiring: install a U.L.-listed/CSA-

certified clamp connector to the terminal box. If using conduit, use a U.L-listed/CSA-certified conduit connector,

- If you are installing a power supply cord kit, do so

now, following kit instructions.

terminal

II ,,:,, q I_

J box cover

cable clamp

dishwasher wires

"_!Jconnector

Turn both front leveler legs to the same height.

If the minimum cutout height is less than 34" (86.4 cm), the rear wheels can be

removed for additional clearance.This will allow the dishwasher to fit into a 33-7/8"

(86 cm) high cutout, but the dishwasher will be more difficult to move into

position. If the wheels are removed, protect the floor when moving the dishwasher.

front leg

if you have built-up / countertop

floors a

Measure height of opening from underside of

countertop to built-up floor. If the height is at least 33-3/4" (85.7 cm), the

dishwasher will fit into the

modification to the shim opening without --_ _ _to_p countertop or flooring. /

2. Put wheels in position 1 and turn the front leveler legs up all the way.

3. Add shims as needed in the area shown to bring dishwasher up to proper height.

NOTE: Shims must be securely attached to floor to prevent their movement when the dishwasher is operated.

shim shim

33-3/4"

(86.7 cm)

min.

HelpfulTip: Put cardboard under dishwasher until it is installed in cabinet opening.The cardboard will help protect floor covering during installation.

2-3/4" 6" 2 --

(ZOcm) (15.2 cm) (ZOcm)

+ 22 hidden pages