Whirlpool GSXP 7527 INSTRUCTION FOR USE

Before using the dishwasher, read the user instructions!

GSXP 7527		Quick Reference Guide				GB

Options 3)

On button

Time and failure display

Off button

Programme selection button

The selected programme is shown in the window of the display.

Start button

Switches “on” when the dishwasher is operating. Flashes when a fault occurs. Switches off at the end of the programme.

Reset button

After pressing the Reset button, the selected programme and the supplementary functions are cancelled (except the detergent and water hardness settings, see user instructions) and must be reset. On releasing the button this is confirmed by an acoustic signal.

Indicators

Add rinse aid

Add regeneration salt

Only add regeneration salt immediately before starting a wash programme.

Indicates in hours the time remaining until the start of the wash cycle. Toward the end of the programme, during the drying cycle, the display will indicate the time remaining in minutes.

“F....” Identification of faults for service technician

“Delayed start” button

The wash cycle can be programmed to start after 1 - 24 hours. With each successive touch of the button, the delayed start indicator increases by 1 hour, and after 24 returns to 00. Then press the Start button. The dishwasher will start at the set time.

“Half load - Multizone” button

Load the upper or lower rack only.

This function can be used with any programme. Press once = upper rack

(the indication lamp/symbol comes on) Press twice = lower rack

(the indication lamp/symbol comes on)

Press 3 times = Off (half load function deactivated). When washing without the top rack, press the “Half Load” button twice, or “Lower rack wash” (the corresponding LED/symbol comes on).

Set detergent

(when the appliance is used for the first time and when using a different type of detergent)

Off indicator = detergent (powder, gel, tablets) Left indicator =2 in 1 detergent

Right indicator = 3 in 1 / 4 in 1 detergent

Antibacterial rinse 4) 5)

This function adds an antibacterial rinse at the end of the wash cycle, thereby guaranteeing a perfectly clean and sanitized load. The lamp will light up when the function is activated. If the temperature is not maintained during the antibacterial cycle (e.g. if the door is opened and remains open for a long time), the lamp will start

blinking to indicate that sanitation is not guaranteed.

	Programme chart			Detergent 2)		Consumption 3)
	Programmes		Loading instructions	A	B	Litres	kWh	Minutes
	Pre-Rinse	cold	Crockery to be washed later.	-	-	4.0	0.03	14
	Quickwash	40°C	Lightly soiled crockery with no	X	-	10.0	0.65	30
			dried-on food.
	Bio 1) 5) 6)	50°C	Normally soiled crockery.	X	X	13.0	1.05	195
	Standard 5)	60°C	crockery.Normally or heavily soiled	X	X	13.0	1.25	120
	Intensive 5)	70°C	Recommended programme for
			heavily soiled crockery, especially	X	X	14.0	1.55	155
			suitable for pans and saucepans.

1)Reference programme for energy label EN 50242;

2)Refer to “User instructions”;

3)Programme data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g.: different loads, options, water temperatures - above or below 15°C - as well as water hardness and power supply voltage, etc.

4)The bacteria removal efficiency has been tested by the Institut Pasteur de Lille (France), based on the NF

EN 13697 standard of November 2001.

5)These programmes can be used with the Antibacterial rinse option.

6)Energy saving programme with prolonged drying cycle.

Important information for Test Laboratories:

For detailed information on the EN comparison test and other tests, contact the following address: “[e-mail]”.

5019 496 90468

(We reserve the right to make technical modifications)

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance

Select, save, and supply the detergent

Press the ON / OFF button.
(The first time you use the appliance
and when using a different type of
detergent)	A	B C

1.Select the third programme from the top in the relative table.

2.Press the Start button for about 7 seconds until the display changes.

3.Select the required detergent with the Start button (OFF = powder

detergent, 2 in 1, 3 in 1, 4 in 1) (shown on the display).

4.Switch the appliance off and then switch it on again. The selected detergent type will be shown on the display for approximately 3

seconds after switching on.

For dosage of powder detergent in compartment A and B refer to the programmes table.

Check the rinse aid level

Check the regeneration salt level

Load the racks

Close the dishwasher door, turn on the water tap

Select a programme

Select additional options

Press the Start button

Wash cycle

Switch off the appliance

Turn off the water tap, unload the racks

Mechanical indicator lamp C.

Electric indicator on control panel (if provided).

On models with water softener system only.

Mechanical indicator lamp D. Electric indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

The last programme selected will light up.

Select the desired programme (using the specific button or knob). The corresponding indicator lamp lights up.

If necessary (and if provided).

The corresponding indicator lamp lights up.

The selected programme is then memorised (even in the event of power failure).

“Change programme in progress”

Press the START button for 2 sec. until the Start indicator lamp switches off.

Select another programme and press the START button again.

-Only open the dishwasher if necessary (Warning: beware of hot steam).

-If the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted.

Only after the START button has switched off: Press the ON / OFF button. All the indicator lamps switch off.

Warning: When the door is opened steam comes out!

Unload the appliance, starting from the lower rack.