Whirlpool GSIE 6484 IN, GSIE 6484 WS, GSIE 6484 AL, GSIE 6484 SW, GSIE 6484 BR INSTRUCTION FOR USE

Before using the dishwasher, read the user instructions!

GSIE 6484

Quick Reference Guide

GB

Wash cycle

Programme selector knob

On / Off button

Start button

Switches “on” when the dishwasher is operating. Flashes when a fault occurs. Switches off at the end of the programme.

Indicators

Add regeneration salt

Only add regeneration salt immediately before starting a wash programme.

Add rinse aid

						Programme
Pre-Rinse			Washing		Drying
							end

Options

Time and failure display 3)

Indicates in hours the time remaining

until the start of the wash cycle.

Switches off at programme start and

indicates the remaining time in hours

and minutes.

“F ....” Information for the After-Sales Service

“Delayed start” buttons

The wash cycle can be programmed to

start after 1 - 24 hours. With each

successive touch of the button, the

delayed start indicator increases

by 1 hour, and after 24 returns to 00. Then press the Start button. The dishwasher will start at the set time.

		Programme chart			Detergent 2)		Consumption 3)
	Programmes			Loading instructions	A	B	Litres	kWh	Minutes
		AutoNormal	50-60°C	Automaticprogrammerecommended
				for routine washes, with dried-on	X	X	13-19	1.15-1.50	90-120
				food (for example for EN 50242).
		Rapid 30 min	40°C	Lightly soiled crockery with no	X	-	13.0	0.70	30
				dried-on food.
		Eco 1)	50°C	Normally soiled crockery.	X	X	16.0	1.05	120
		Intensive	70°C	Heavily soiled crockery, especially	X	X	22.0	2.15	125
				pots and pans.

1)Reference programme for energy label in compliance with EN 50242 regulations;

2)Refer to “User instructions“;

3)Values may vary in relation to usage, e.g.: different loads, water temperatures - above or below 15°C - as well as water hardness and power supply voltage, etc.

5019 496 90192

(We reserve the right to make technical modifications)

BK/I/B/GB

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance		Press the ON / OFF button.
		Large compartment A:
		With each wash cycle.	A B	C
How to fill the
detergent dispenser		Small compartment B:
		For programmes with pre-wash only.
		Mechanical indicator lamp C.
Check the
rinse aid level		Electric indicator on control panel (if provided).

Check the regeneration salt level

Load the racks

Close the door, turn on the water tap

Select a programme

Select additional options

Press the START button

Wash cycle

Switch off the appliance

Shut off the water tap, unload the racks

On models with water softener system only.

Mechanical indicator lamp D.

Electric indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

The last programme selected will light up.

Select the desired programme (using the specific button or knob). The corresponding indicator lamp lights up.

If necessary (and if provided) the corresponding indicator lamp lights up.

The selected programme is then memorised (even in the event of power failure).

“Change programme”

Press the START button for 2 sec. until the Start indicator lamp switches off; Select another programme and press the START button again.

-Only open the dishwasher if necessary (Warning: beware of hot steam).

-If the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted.

Only after the START button has switched off: Press the ON / OFF button. All the indicator lamps switch off.

Warning: when the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

BK/II/B/GB