49696034GB.fm Page 1 Monday, June 28, 2010 7:13 PM
Before using the dishwasher, read the user instructions!
GMXI 5010 SD Quick Reference Guide |
GB |
|
On/Off button
Press the ON button to switch on the dishwasher. The indicator lamp of the last programme selected lights up; at the end of the cycle a short acoustic signal sounds.
Start button
Press to start the wash cycle and keep pressed until an acoustic signal confirms the start of the cycle and the indicator lamp of the selected programme flashes.
Indicators
Add regeneration salt
Only add regeneration salt immediately before starting a wash programme.
Add rinse aid
Option
“Delayed start” button
The wash cycle can be programmed to start after 3-6-9 hours.
Press button to select the delayed start. The corresponding indicator lamp lights up. After a pre-wash of the dishes the previously set wash is started. To quit selection and start the wash program without the delayed start, press button until the 3-6-9 indicator lamps go off.
Fault indicators
Indicators
Off
Blinking
On
Water stop device activated
Switch off the dishwasher and contact the After-sales Service.
The dishwasher over fills with water
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
The water heating system is not working
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
Water heating anomaly
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
The dishwasher does not fill with water
Check the water supply and filters, and make sure that there are no kinks in the water inlet hose. Open and close the door in order to continue.
The dishwasher does not drain
Make sure that the filter unit and drain hose are not clogged and if necessary clean them.
Flow meter (if provided) anomaly
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
Alternatewashingsystem(ifprovided)anomaly
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
Fault in water load system
Switch off the dishwasher and contact the After-Sales Service.
|
Programme chart |
Detergent 2) |
Consumption 3) |
||||
Programmes |
|
Loading Instructions |
A |
B |
Litres |
kWh |
Minutes |
|
|
|
|
|
|
|
|
Pre-Rinse |
cold |
Crockery to be washed later. |
— |
— |
6.0 |
0.03 |
16 |
|
|
|
|
|
|
|
|
Rapid 30 min |
45°C |
Lightly soiled crockery with no dried-on food. |
X |
— |
13.0 |
1.00 |
30 |
|
|
|
|
|
|
|
|
Bio 1) |
55°C |
Normally soiled crockery. |
X |
— |
14.0 |
1.05 |
140 |
|
|
|
|
|
|
|
|
Normal |
65°C |
Normally or heavily soiled crockery. |
X |
X |
17.0 |
1.28 |
90 |
|
|
|
|
|
|
|
|
Intensive |
70°C |
Recommended programme for heavily soiled |
X |
X |
20.0 |
1.45 |
110 |
|
|
crockery, especially suitable for pans and saucepans. |
|
|
|
|
|
|
|
|
|
|
|
|
|
1)Reference programme for energy label in compliance with EN 50242 regulations (upper rack in upper position).
2)Refer to “User instructions”.
3)Programme data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g.: different loads, water temperatures - above or below 15°C - as well as water hardness and power supply voltage, etc.
5019 496 96034
(We reserve the right to make technical modifications)
Black process 45.0° 150.0 LPI
49696034GB.fm Page 2 Monday, June 28, 2010 7:13 PM
How to use the appliance
Further indications are given in the single chapters and in the user instructions.
|
|
|
|
|
|
|
Open the door |
Press the On/Off button . |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Large compartment A |
|
C |
|
|
How to fill the |
|
A B |
|
|
||
|
|
|
|
|||
|
|
|
|
|||
detergent dispenser |
Small compartment B |
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Check the rinse aid level
Check the regeneration salt level
Load the racks
Select a programme
Select additional options
Press the Start button to start the programme
Mechanical indicator lamp C.
Electric indicator on control panel (if provided).
On models with water softener system only. |
|
D |
|
Mechanical indicator lamp D. |
|
|
|
Electric indicator on control panel |
|
|
|
(if provided). |
|
|
|
|
|
|
|
Refer to the dishwasher loading instructions. |
|
||
Press the |
button until the desired programme lights up. |
|
If necessary (and if provided).
The corresponding indicator lamp lights up.
“Cancel”
Press and keep pressed
until an
acoustic signal confirms your selection (the indicator lamp stops flashing and remains lit). Press again and keep pressed until the “end” indicator lamps light up.
All water in the tank will be drained and the programme will be stopped immediately.
“Change programme in progress”
Press and keep pressed until an acoustic signalconfirmsyourselection(theindicator lamp stops flashing and remains lit).
Select a new programme.
Start the programme.
Turn on the water tap, close the door
Wash cycle
Switch off the appliance
Turn off the water tap, unload the racks
- Only open the dishwasher if necessary (Warning: beware of hot steam).
- If the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted.
At the end of the programme a short acoustic signal will sound.
The indicator lamps 4 + 5 (marked by “end” on the control panel) light up. Open the door and press the On/Off button .
All the indicator lamps go off.
Warning: When the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
Black process 45.0° 150.0 LPI