Whirlpool GI6FARXXY02, GI6FDRXXB01, GI6SARXXF00, GI6FARXXB00, GI6FDRXXB03 Use And Care Manual

...

0 (0)

THANKYOUforpurchasingthishigh-qualityproduct.IfyoushouldexperienceaproblemnotcoveredinTROUBLESHOOTING, pleasevisitourwebsiteatwww.whirlpool.comforadditionalinformation.Ifyoustillneedassistance,callusat1-800-253-1301. InCanada,visitourwebsiteatwww.whirlpool.caorcallusat1-800-807-6777.

Youwillneedyourmodelandserialnumber,locatedontheinsidewalloftherefrigeratorcompartment. Paraobteneraccesoa"lnstruccionesparaelusuariodelrefrigerador"enespa_ol,oparaobtenerinformaci6nadicionalacercade

suproducto,visite:www.whidpool.com.

Necesitara su nQmerode modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

Tableof Contents/ Tabledes matibres

REFRIGERATOR SAFETY ..................................................................... 1

INSTALLATION INSTRUCTIONS ......................................................... 2

REFRIGERATOR USE ........................................................................... 7

REFRIGERATOR CARE ....................................................................... 11

TROUBLESHOOTING .......................................................................... 12

WATER FILTER CERTIFICATIONS .................................................... 14

PERFORMANCE DATA SHEET .......................................................... 15

WARRANTY .......................................................................................... 16

SI_CURITI_ DU RI_FRIGI_RATEUR ..................................................... 17

INSTRUCTIONS D'INSTALLATION ................................................... 18

UTILISATION DU RI_FRIGI_RATEUR ................................................. 23

ENTRETIEN DU RI=FRIGI=RATEUR ................................................... 27

DI_PANNAGE ........................................................................................ 28

FEUlLLE DE DONNI=ES SUR LA PERFORMANCE .......................... 31

GARANTIE ............................................................................................ 32

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

W10314956A

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help

prevent accidents.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor

damage could occur.

Remove the Packaging

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a V2" (1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall, leave a 33/4'' (9.5 cm) minimum space between the refrigerator and wall to allow the door to swing open.

NOTE: It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. Do not install the

refrigerator in a location where the temperature will fall below 55°F (13°C).

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn Cooling OFF, and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and turn Cooling

ON. See "Using the Controls."

1/2" (1.25 cm)

33/4" (9.5 cm)

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1A"Nut driver

• 7A6"and V2"Open-end or two • _A"Drill bit adjustable wrenches • Cordless drill

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3A6"(4.76 mm) saddle valve which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

• For models with water filters, the disposable water filter should be replaced at least every 6 months.

Water Pressure

A cold water supply with water pressure of between 35 and 120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. Ifyou have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).

Ifareverseosmosiswaterfiltrationsystemisconnectedtoyour coldwatersupply,thewaterpressuretothereverseosmosis

systemneedstobeaminimumof40to60psi(276to414kPa). Ifthewaterpressuretothereverseosmosissystemislessthan

40to60psi(276to414kPa):

• Checktoseewhetherthesedimentfilterinthereverse osmosissystemisblocked.Replacethefilterifnecessary.

• Allowthestoragetankonthereverseosmosissystemtorefill afterheavyusage.

Ifyourrefrigeratorhasawaterfilter,itmayfurtherreducethe waterpressurewhenusedinconjunctionwithareverse

osmosissystem.Removethewaterfilter.See"WaterFiltration System."

Ifyouhavequestionsaboutyourwaterpressure,callalicensed, qualifiedplumber.

Readalldirectionsbeforeyoubegin. IMPORTANT:Ifyouturntherefrigeratoronbeforethewaterlineis

connected,turntheicemakerOFE

7. Slipthecompressionsleeveandcompressionnutonthe coppertubingasshown.Inserttheendofthetubingintothe

outletendsquarelyasfarasitwillgo.Screwcompressionnut ontooutletendwithadjustablewrench.Donotovertightenor youmaycrushthecoppertubing.

8. Placethefreeendofthetubinginacontainerorsink,andturn ONthemainwatersupply.Flushthetubinguntilwaterisclear.

TurnOFFtheshutoffvalveonthewaterpipe.

Connect to Refrigerator

1. Remove plastic cap from water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Find a V2"to 1V4" (12.7 mm to 31.8 mm) vertical cold water pipe near the refrigerator.

IMPORTAN1"."

• Make sure it is a cold water pipe.

Horizontal pipe will work, but the following procedure must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower right rear of the refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a V4"hole in the cold water pipe you have selected.

D E

F G

A. Cold water pipe

B. Pipe clamp C. Copper tubing D. Compression nut

Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the V4"drilled hole in

the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not

overtighten.

E. Compression sleeve F. Shutoff valve

G. Packing nut

A. Copper tubing B. "P" clamp

3. Turn on water supply to refrigerator and check for leaks. Correct any leaks.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely

fill the ice container.

C. Compression nut D. Compression sleeve

Allgraphicsreferencedinthefollowinginstructionsareincluded laterinthissectionafter"FinalSteps."

Remove and Replace Handles

To Remove Handles:

1. Grasp the lower part of the handle firmly, slide the handle up and pull the handle straight out from the door. See Handle graphic.

To Replace Handles:

1. Position the handle so that the large holes in the mounting clips are down and align the holes with the door studs.

2. Rotate the handle so that the mounting clips are flat against the door and slide the handle down to engage. See Handle

graphic.

Remove Doors and Hinges

NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are

working.

Align the door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Reconnect the wiring plug on top of the left-hand side refrigerator door.

5. Reconnect the water line by pulling back the locking collar ring while firmly pushing the water line into the connector.

6. Check for leaks. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT: Two people may be required to remove and replace

the freezer drawer. Graphics are included later in this section.

IMPORTANT:

• Remove food and any adjustable door or utility bins from doors.

• Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are working.

TOOLS NEEDED: %e", 3/8",1/4"hex-head socket wrench, Torx®t T20 screwdriver, #2 Phillips screwdriver, and a flat-blade

screwdriver.

1. Unplug refrigerator or disconnect power.

2. Remove the base grille. Grasp the grille firmly and pull it toward you.

........

3. Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator

door from the bottom hinge pin.

4. Remove top hinge cover from left side refrigerator door.

5. Disconnect the wiring plug located on top of the hinge by wedging a flat-blade screwdriver or your fingernail between

the two sections. See Connections graphic.

6. Disconnect the water line by pulling back on the locking collar while pulling the water line out of the water line connector. See

Connections graphic.

7. Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the left-hand side door from the bottom hinge pin.

8. Using a 3/8"hex wrench, remove the leveling leg brackets from the bottom of the cabinet. Keep screws for later use.

Replace Doors and Hinges

1. Assemble the parts for the top hinge as shown in Top Hinge graphic. Do not tighten the screws completely.

2. Replace the parts for the bottom hinge as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator door.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to position the two screws in the bottom of the drawer front into the brackets.

See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

1. Replace the base grille.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug into a grounded 3 prong outlet.

3. Return all removable parts to doors and drawer and food to refrigerator and freezer.

t®TORX is a registered trademark of Textron Innovations Inc.

Top Hinges

.<_:,_ ..................A

A. Hinge Cover Screw

B, Top Hinge Cover C, s/18"Hex Head Hinge Screws D. Top Hinge

Bottom Hinges

A. Hinge Pin Cover

B, Bottom Hinge C. Hinge Screws

Connections

A B

xx\

\\x

\\\

A. Wiring Plug B. Water Line Connection

A. Loosen 4 Door Bracket Screws

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

IMPORTANT:

Your refrigerator has two adjustable, front leveling screws - one on each side of the refrigerator base. If your refrigerator

seems unsteady or you want the door to close easier, use the instructions below.

Before moving the refrigerator, raise the leveling screws so the front rollers are touching the floor.

Remove the base grille. Grasp the grille firmly and pull it toward you.

2. Raise or lower the cabinet. Using a V4"hex driver, turn the leveling screw on each side to

raise or lower that side of the refrigerator. NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws. It may take several turns of the leveling screw to adjust the tilt of the refrigerator.

• To raise, turn the leveling screw clockwise.

• To lower, turn the leveling screw counterclockwise.

REFRIGERATORUSE

There are two refrigerator compartment doors. The doors can be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically forms a seal between the two doors.

A.Hinged seal

A. Leveling screw

Open the door again to make sure that it closes as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise. It may take several

more turns, and you should turn both screws the same amount.

4. Replace the base grille.

The control center is located on the front of the ice and water dispenser.

Temperature Controls

For your convenience, your temperature controls are preset at the factory. When you first install your refrigerator, make sure the controls are still set to the recommended set points as shown.

Recommended Settings

IMPORTANT:

• When the power is on, the temperature display shows the set point temperature of the compartment.

Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled

completely, your food may spoil. NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool the compartments any faster.

The recommended settings should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold asyou like and when ice cream is

firm.

• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

CoolingOn/Off:

• CoolingOn/Offturnsoffcoolingforbothcompartments.It doesnotdisconnectpowertotherefrigerator.

• PressandholdCoolingOn/Offfor3seconds.TheLEDwill lightuptoindicatethatcoolingisOff.Pressthebuttonagain toturnonthecooling.TheLEDwillturnoff.

R_frigerat o_

Cooling Off Press3 5ec

Humidity Control

The humidity control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator uses more energy when Humidity Control is on.

• Press Humidity Control to turn on the door heater. Press Humidity Control again to turn off the heater. The LED will be

illuminated when Humidity Control is on.

@°

HUMIDITY CONTROL

Adjusting Controls

The REFRIGERATOR control adjusts the refrigerator compartment temperature. The FREEZER control adjusts the freezer compartment temperature.

If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures: The first touch of the (+) or (-) touch pad displays the current

temperature set point.

• Press the (+) or (-) touch pads until the desired temperature set point is displayed.

NOTE: Except when first turning on the refrigerator, do not adjust either temperature control more than one setting at a time. Wait

24 hours between adjustments for the temperature to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

1° lower

FREEZER too warm/too little ice FREEZER Control 1°

lower

REFRIGERATOR too cold REFRIGERATOR Control

1° higher

FREEZER too cold FREEZER Control 1°

higher

Additional Control Center Features

Fast Cool The Fast Cool feature assists with periods of high refrigerator use,

full grocery loads, or temporarily warm room temperatures.

• Press the Fast Cool touch pad to set the freezer and refrigerator to the lowest temperature settings. Press the Fast Cool touch pad again to return to the normal refrigerator set point.

NOTE: The Fast Cool feature will automatically shut off in approximately 2 hours. When Fast Cool is on, the temperature cannot be adjusted.

FASTCOOL

Door Alarm

The Door Alarm feature sounds a chime every few seconds when the refrigerator door has been left open for 5 continuous minutes.

The chime will sound until the door is closed or Door Alarm is turned off.

• Press the Door Alarm touch pad to turn this feature on or off. The indicator light will be lit when the Door Alarm feature is on.

DOOR ALARM

Filter Reset

The Filter Reset control allows you to restart the water filter status tracking feature each time you replace your water filter. See

"Water Filtration System."

• Press and hold the Filter Reset touch pad for 3 seconds, until the Order or Replace light turns off.

ORDE_P_-ACE

FILTER RESET

_EssANO_OtD

User Preferences

The control center allows you to set user preferences, if desired. Temperature Display (F C)

This preference allows you to change the temperature display. F - Temperature in degrees Fahrenheit C - Temperature in degrees Celsius

Alarm (AL) This preference allows you to turn off the sound of all alarms. ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

Auto Light Level Selection (LL)

This preference allows you to adjust the dispenser light level from dimmest to brightest (settings 1 through 9).

NOTE: The Auto Light feature on the control center must be selected to activate this preference.

Sabbath Mode (SAD)

ON - All control center lights, interior lights and alarm tones will be disabled.

OFF - All control center lights, interior lights and alarm tones will be enabled.

NOTE: Press the door alarm touch pad for 3 seconds to restore all lights.

To Access the User Preferences Menu:

1. Press and hold the Door Alarm touch pad for 3 seconds. The preference name will appear in the Freezer display and the

preference status (F or C) or (ON or OFF) will appear in the Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the preference names. When the desired preference name is

displayed, press the Refrigerator (+) or (-) touch pads to change the preference status.

3. Set your preferences by pressing and holding the Door Alarm touch pad for 3 seconds.

3. Push the ice bin in until resistance is felt. Raise the front slightly and push the ice bin in until an audible "click" is heard.

You can control the amount of humidity in the moisture-sealed crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH. FRUIT/LOW (open) for best storage of fruits and vegetables with

skins. VEGETABLES/HIGH (closed) for best storage of fresh, leafy

vegetables.

IMPORTANT:

• Flush the water system before turning on the ice maker. See "Water and Ice Dispenser."

• The ice maker and storage bin are located in the upper left- hand side of the refrigerator compartment.

Turning the Ice Maker On/Off

The On/Oft switch is located on the ice maker. To turn on the ice maker, press the switch to the ON position. To manually turn off the ice maker, press the switch to the OFF

position. NOTE: Your ice maker has an automatic shutoff. The ice maker sensors will automatically stop ice production, but the control will

remain inthe ON position.

Removing and Replacing Ice Storage Bin

To Remove the Ice Storage Bin:

1. Hold the base of the storage bin and press the release button on the lower right.

2. Pull the storage bin out until resistance is felt. Lift up the front of the ice bin and remove.

3. Press the switch to the OFF position

To Replace the Ice Storage Bin: IMPORTANT: It may be necessary to turn the auger driver, behind

the ice bin, counterclockwise to properly align the ice bin with the auger driver. The ice storage bin must be locked in place for

proper ice dispensing.

1. Press the switch to the ON position

2. Slide the ice bin into the guide rails located on either side of the enclosure.

A. ON position B. Auger driver

Ice Production Rate

Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill the ice storage bin.

The ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period.

To increase ice production, lower the freezer and refrigerator temperature. See "Using the Controls." Wait 24 hours between adjustments.

Remember

The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well

maintained. Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice bin and dispenser mechanism. Do not store anything on top of the ice maker or in the ice

storage bin.

IMPORTANT:

After connecting the refrigerator to a water source, flush the water system. Use a sturdy container to depress and hold the water dispenser pad for 5 seconds, then release it for

5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser pad (5 seconds on, 5 seconds off) until a total of 4 gal. (15 L) has been dispensed. This will flush air from the

filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser.

NOTE: After five minutes of continuous dispensing, the dispenser will stop dispensing water to avoid flooding. To continue dispensing, remove the container and press the dispensing lever again.

• The dispenser will dispense either water or cubed ice.

• Allow 24 hours for the refrigerator to cool down and chill water. Dispense enough water every week to maintain a fresh supply.

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

Dispense Ice and Water

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

Select water or cubed ice by pressing the corresponding button on the dispenser control panel. A light above the button indicates your selection.

O ®

WATER ICE

Press a sturdy container against the dispenser lever. IMPORTANT: You do not need to apply a lot of pressure to the

lever in order to activate the dispenser. Pressing hard will not make the water or ice dispense faster or in greater quantities.

3. Remove the container to stop dispensing.

Dispenser Light

NOTES:

• The dispenser lights are LEDs which should not need to be changed.

• When you use the dispenser, the lever will automatically turn the light on. If you want the light to be on continuously, you

may choose either On or Auto.

To Lock and Unlock Dispenser:

Press and hold the LocWUnlock touch pad for 3 seconds to lock the dispenser. The indicator light will illuminate when Lock is on.

Press and hold the LocWUnlock touch pad again for 3 seconds to unlock dispenser. The indicator light will turn off.

LOCKOUT

_ss A_D_OLD

The water filter status lights help you know when to change your water filter. When the water filter status icon changes from Normal (blue water) to Order (red waves) and "Order Filter" (orange) this tells you that it is almost time to change the water filter. Replace the disposable water filter when "Replace Filter" (red) illuminates and the icons blink continuously during dispensing.

NOTES:

• After 14 days at Replace Filter stage, the "Replace Filter" and "water" icons will glow (red) at all times and blink

continuously during dispensing. Also, an alert chime will sound three times following dispensing.

• The disposable water filter should be replaced at least every 6 months. If the water flow to the water dispenser or ice maker

decreases noticeably before 6 months have passed, replace the water filter more often. To change the filter, see "Water Filtration System."

After changing the water filter, reset the water filter status. On the display screen, press and hold FILTER RESET for 3 seconds. The status light will change from Replace Filter (red) to Normal (blue water) when the system is reset.

The water filter is located in the upper right-hand corner of the refrigerator compartment.

AUTO LIG_N

LIGHT

0- AUTOSENSOR

Auto: The dispenser light will illuminate at half-power when the

light sensor detects the light levels inthe room are low. To turn the dispenser light on, press the Light button. The Auto indicator light

will illuminate. On: For continuous light, press the Light button a second time.

The On indicator light will illuminate. Off: To turn the dispenser light off, press the Light button a third

time.

Dispenser Lock

The dispenser can be locked for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The dispenser lock does not shut off power to the product, to the ice maker, or to the dispenser light. It just deactivates all keypad functions.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Replacing the Water Filter

To purchase a replacement water filter, model number UKF8001AXX-200, contact your dealer or call 1-877-253-1301 in

the U.S.A. or 1-800-807-6777 in Canada. IMPORTANT: Air trapped inthe water system may cause water

and filter to eject. Always dispense water for at least 2 minutes before removing the filter or blue bypass cap.

1. To access the filter, press upward on the ribbed section of the water filter cover.

Turn filter counterclockwise to remove.

Remove sealing label from replacement filter and insert the filter end into the filter head.

Turn the filter clockwise until it stops. Snap the filter cover closed.

5. Flush the water system. See "Water and Ice Dispenser."

NOTE: The dispenser feature may be used without a water filter

installed. Your water will not be filtered. If this option is chosen, replace the filter with the blue bypass cap.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid odor

buildup. Wipe up spills immediately.

IMPORTAN1"."

Because air circulates between all compartments, any odors formed in one compartment will transfer to the other. You must thoroughly clean all compartments to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover

foods tightly. Do not use abrasive or harsh cleaners such as window sprays,

scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, nail polish remover, bleaches or

cleansers containing petroleum products. Do not use paper towels, scouring pads, or other harsh cleaning tools that may scratch or damage the materials.

Clean the Interior

1. Unplug refrigerator or disconnect power.

2. Using a clean sponge or soft cloth and a mild detergent in warm water, hand wash, rinse, and dry removable parts and interior surfaces thoroughly.

3. Plug in refrigerator or reconnect power.

Clean the Touch Screen Display on the Dispenser Panel

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner and Polish to come into contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.

3. Plug in refrigerator or reconnect power.

Clean the Condenser

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure

maximum efficiency. To clean the condenser:

1. Unplug refrigerator or disconnect power.

2. Remove the base grille.

3. Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the

condenser.

4. Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to replace the bulb with an appliance bulb of the same size, shape, and wattage (no greater than 40 watts).

• The dispenser lights are LEDs that cannot be changed.

• On some models, the interior lights are LEDs that cannot be changed.

• Some models may have LEDs in one compartment and an appliance bulb in another compartment.

To Replace an Appliance Bulb:

1. Unplug refrigerator or disconnect power.

2. Remove the light shield(s), if necessary.

• Squeeze both sides of the light shield while pulling

downward to remove.

Make sure the refrigerator is unplugged or the power is disconnected before wiping the screen, to avoid

unintentionally changing the settings.

Mix a solution of mild detergent in warm water. Dampen asoft, lint-free cloth with the solution and gently wipe the screen.

NOTE: Do not spray or wipe liquids directly onto the screen, or over-saturate the cloth.

3. Plug in refrigerator or reconnect power.

Clean the Exterior Surfaces

Unplug refrigerator or disconnect power.

Using a clean sponge or soft cloth and a mild detergent in warm water, wash, rinse and thoroughly dry stainless steel

and painted metal exteriors.

• To keep your stainless steel refrigerator looking like new and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel Cleaner and Polish, Part Number 4396095. To order the cleaner, call 1-800-253-1301 U.S.A. or 1-800-807-6777

Canada.

Replace burned-out bulb(s) with appliance light bulb(s) no greater than 40 watts.

Replace the light shield(s) by inserting the tabs on the shield into the liner holes and snap into place.

NOTE: To avoid damaging the light shield, do not force the shield beyond the locking point.

5. Plug in refrigerator or reconnect power.

+ 23 hidden pages