QUICK REFERENCE GUIDE
GB
BEFORE USING THE APPLIANCE FOR THE FIRST TIME:
• IMPORTANT: MAKE SURE YOU HAVE READ THE INSTALLATION.
• REMOVE THE TRANSIT SCREWS AND TRANSIT BAR BEFORE USING THE
MACHINE FOR THE FIRST TIME.
• First wash cycle without laundry:
Open the tap.
1.
Close the door.
2.
Pour a little detergent (about 100 ml) into the detergent compartment .
3.
Select a short wash programme (see programme chart).
4.
Switch on the appliance.
5.
This will remove any water remaining in the machine from the manufacturer's test run.
ROUTINE WASHES:
Open the tap.
1.
Sort the laundry according to fabric type and colour and load the machine.
2.
Close the door.
3.
Add detergent and any additives required.
4.
Select the programme, temperature and special options (depending on model).
5.
Switch on the appliance.
6.
3
GB
CONTENTS
APPLIANCE AND ACCESSORIES
INSTALLATION
PROTECTING THE ENVIRONMENT
SAFETY INSTRUCTIONS
MOVING AND TRANSPORTING THE APPLIANCE
SORTING THE WASH
DETERGENT AND ADDITIVES
LIQUID DETERGENTS
LIQUID BLEACH (HYPOCHLORITE)
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
5
6
8
8
8
9
10
11
12
DYEING
REMOVING THE FILTER
DRAINING RESIDUAL WATER
WASHING MACHINE INSTALLED IN ROOM
EXPOSED TO FREEZING TEMPERATURES
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
12
12
13
13
14
15
15
4
APPLIANCE AND ACCESSORIES
1. Worktop
2. Control panel
3. Detergent drawer
4. After-Sales Service sticker (inside door)
5. Door
6. Door handle
- To open: pull handle
- To lock: press the door firmly (the lock will click into place)
7. Filter (inside compartment door).
5
.
INSTALLATION
TRANSIT SCREWS
The appliance is fitted with two transi t screws and
a transit bar to prevent internal damage while it is
being moved.
Before using the appliance the transit screws
and transit bar MUST be removed.
The appliance is fitted with two screws and a
transit bar.
1.
Remove the black screw
screwdriver.
2.
Unscrew the screw
with a screwdriver.
3.
Completely withdraw and remove the transit
(C)
bar
by pulling firmly on the red handle.
Keep the screws and the bar for future use.
Note:
Refit the transit screws and transit bar before transporting the appliance by repeating the above
steps in reverse order. In order to locate the screws and bar corre ctly, it will be necessary to remove the
appliance top, having first made sure that th e appl iance is disc onnec ted from wat er and elec tricit y
supplies.
INSTALLATION
•
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
•
Make sure that all four feet are resting firmly
on the floor and check that the appliance is
perfectly level (use a spirit level).
•
If the floor is uneven, adjust the levelling feet
as required (do not insert pieces of wood,
cardboard etc. under the feet).
1.
Slacken the locknut.
2.
Adjust the height of the foot, turning it by
hand.
3.
Tighten the locknut anticlockwise towards
the washing machine.
If the appliance is to be installed on a wooden
floor, distribute the weight by placing it on a
60x60 cm sheet of plywood at least 3 cm in
thickness. Secure the plywood sheet to the floor.
(A)
with a
(B)
on the red transit bar
t
WATER SUPPLY
•
Water supply: only cold water.
•
Tap: 3/4” threaded hose connector.
•
Water pressure (mains pressure):
10-100 N/cm
2
(1-10 bar).
INLET HOSE
•
Carefully screw the inlet hose to the tap by
hand.
•
Turn the tap on fully and check that the joints
at the washing machine and the tap are
watertight.
6
•
If the hose is not long enough, replace it with
a suitable length of pressure-resistant hose
(approved under EN 500 65 to withstand a
minimum of 10 bar).
•
Check the hose regularly for brittleness and
cracks and replace if necessary.
•
The washing machine may be connected
without a non-return valve.
•
Observe any special local regulations
regarding connection to the water supply.
INSTALLATION
DRAIN HOSE
•
Drain hose connection to water outlet.
1.
Unhook the drain hose from the left clip;
see arrow
Important:
Do NOT loosen the drain hose connection;
see arrow
leakage (danger of scalding with hot water).
2.
Fit the drain hose either to the siphon or hook
it over the edge of a sink or bath tub with the
“U” bend. Small hand basins are not suitable.
3.
Minimum drain height: 60 cm.
Maximum U-bend drain height: 90 cm.
4.
If you need to add an extension, use a
flexible hose of the same type and secure the
union with screw-on hose clips. Maximum
overall drain hose length 2.5 m.
Important:
Make sure that there are no kinks in the drain
hose run and take precautions against it falling
while the appliance is running.
(A)
.
(B)
, otherwise there is the risk of
CONNECTION TO THE MAINS
•
Observe local utility company regulations.
•
The connection must be made with a
correctly installed, earthed and insulated
socket.
•
The system must be earthed.
The manufacturer declines all responsability
for injury to persons or pets and damage to
property caused by disregarding the above
instructions.
•
The data concerning voltage, consumption
and necessary fuse are supplied on the
inside of the appliance door.
•
The mains connection cable may only be
replaced by a qualified electrician.
•
The appliance conforms to European safety
regulations, EC directive 93/68/EWG and
EN 60555.
•
Do not use extension leads or multiplugs.
7
PROTECTING THE ENVIRONMENT
• Packing
The packaging is marked with the recycling
symbol , signifying that it can be
100% recycled.
• Appliance
The appliance is made of recyclable
materials. Dispose of the appliance in
conformity with environmental regulations.
Make it inoperable: pull out the plug and cut
off the power cable so that the appliance
cannot be connected to the mains.
SAFETY INSTRUCTIONS
• The appliance must only be used in the
household for the prescribed uses.
• All connections to the water and electrical
mains must be made in accordance with the
manufacturer's instructions and following
local utility company safety regulations
(see “Installation ”).
• Before any cleaning and maintenance,
switch off the machine or disconnect it from
the mains.
• Switch off the washing machine and turn off
the tap whenever the machine is not in use.
• Eco-tips
- A full load (depending on the programme
selected) gives the best energy and water
consumption.
- Laundry which is lightly to moderately soiled
does not require a prewash.
- Lightly soiled laundry should be washed at a
low temperature or with a short programme.
- When washing small loads press the “Lightly
Soiled” / “Half load” button (if present)
and use less detergent.
- Do not exceed the recommended dosages
on the detergent packet.
- Only use bleach or stain remover if
absolutely necessary.
• Never use excessive force to open the door.
• Children must not be allowed to play with or
inside the machine. Do not rest any weight on
the door.
• Packaging materials can be dangerous for
children. Keep the packaging material
(plastic bags, polystyrene, etc.) well out of
their reach.
• The appliance conforms to European safety
regulations, EC directive 93/68/EWG and
EN 60555.
MOVING AND TRANSPORTING THE APPLIANCE
1. Pull out the mains plug.
2. Shut off the water tap.
3. Disconnect the inlet and drain hoses.
4. Drain residual water from the appliance and
hoses (see “Draining Residual Water”).
5. Fit the transit screws and transit bar
(see “Installation ”).
8
SORTING THE WASH
1. Sort the load according to:
• Fabric type / care label symbol
Cotton, mixed fibres, synthetics, wool.
• Colours
Separate coloured and white articles. Wash new
coloured articles separately.
• Article size
Washing articles of different sizes together
improves wash efficiency and distributes the load
better in the drum.
• Fabric delicacy
Wash delicates separately. Sele ct th e ap prop ri at e
special programme for machine - washable
wool , curtains or delicates. Either remove curtain
hooks or tie into a cloth ba g. O nly wa sh mach in ewashable fabrics. Wash small articles (e.g. nylon
stockings, belts etc.) and art ic l es wi th h ook s (e .g .
bras) in a cloth bag or pillow case with zip.
2. Empty all pockets
Coins, safety pins etc. can damage the laundry,
drum and tub.
3. Closures
Close zips and hooks and eyes. Loose belts or
ribbons should be tied together.
STAIN REMOVAL
• Blood, milk, egg, and other organic substances are
generally removed by the enzyme phase of the
programme.
• To remove red wine, coffee, tea, grass and fruit
stains, etc. add a biological stain removing agent
to the main wash in chamber of the detergent
drawer.
• Particularly stubborn stains can be treated with
stain remover before the wash.
LOADING THE WASH
Open the door.
1.
Load the articles one at a time loosely into the
2.
drum, without overfilling.
Close the door.
3.
LOAD CAPACITY
See the programme overview.
Note: Overloading the machine reduces the wash
efficiency and encourages creasing.
1
2
3
9
DETERGENT AND ADDITIVES
CHOOSING THE RIGHT DETERGENT
The type of detergent depends on:
•
the type of fabric (cottons, synthetics,
delicates, wool);
Note:
Use only specific detergents for
washing wool.
•
colour;
•
wash temperature;
•
degree and type of soiling.
Note:
•
Whitish residues on dark fabrics are due to
the insoluble water softeners in modern
phosphate-free detergents. If this occurs,
shake or brush out the fabric or use liquid
detergents.
•
Keep detergents and additives in a safe,
dry place out of the reach of children.
•
Use only detergent and fabric conditioner
specifically produced for automatic domestic
washing machines.
•
When using water softeners, descaling
agents, dyes or bleaches, make sure that
they are suitable for use in domestic washing
machines.
•
Do not use solvents in the machine (e.g.
turpentine, benzine, etc.). Do not wash
fabrics in the machine which have been
treated with solvents or flammable liquids.
DETERGENT DOSAGES
Do not exceed manufacturers’ recommended
dosages as shown on the detergent package.
The amounts depend on:
•
degree and type of soiling;
•
size of wash;
-
full load: according to manufacturers’
instructions;
-
half load: 3/4 of the normal amount;
-
minimum load (about 1 kg): 1/2 the amount
used for full load;
•
water hardness in your area (request
information from the water company): soft
water requires less detergent than hard
water.
Note:
•
Overdosing the detergent results in
excessive foaming and reduces the wash
efficiency.
•
Using insufficient detergent results in grey
laundry. The heating elements and drum also
build up scale.
•
If using chlorine bleach, follow the bleach
instructions carefully. Overdosing the bleach
can damage the wash.
WATER HARDNESS
WATER HARDNESS
CATEGORY
1
2
3
4
10
CHARACTERISTICS
soft
medium
hard
very hard
GERMAN
°dH
0-7
7-14
14-21
over 21
FRENCH
°fH
0-12
12-25
25-37
over 37
ENGLISH
°eH
0-9
9-17
17-26
over 26
DETERGENT AND ADDITIVES
FILLING THE DETERGENT AND
ADDITIVES
1.
Pull out the detergent drawer.
2.
Filling the detergent.
•
Programmes with pre- and main
wash.
•
Main wash programme without
prewash.
•
Add fabric softeners and
conditioners no further than the
“Max” mark (only for washing
machine with detergent drawer with
4 chambers)
•
Fill chlorine bleach only to the
“Max” mark.
•
Stain remover.
•
Water softener
(water hardness class 4).
•
Starching.
Dissolve/dilute the starch, powder
or liquid, in approximately 1 litre of
water in a container. Load the
machine, close the door, select
“Rinse and Spin” and start. Once
the machine has started filling, pour
the dissolved starch into detergent
dispenser chamber . Flush the
chamber straight away by adding
about half a litre of water.
Notes:
•
When using highly concentrated detergents,
use the detergent ball provided with the
detergent and place it directly in the drum to
avoid dispensing problems (for programmes
without pre-wash only).
•
For programmes with prewash: liquid
detergents can be used for the prewash.
For the main wash then a powder detergent
has to be used.
•
Dose the correct amount of concentrated
fabric softener and dilute with water up to the
maximum level marked in the softener
compartment.
Detergent drawer with 3 chambers.
3.
Slide the drawer in until it clicks shut.
LIQUID DETERGENTS
Some machines are supplied with a detachable
insert for the use of these products. This insert
should be inserted into the ma in wa sh
chamber of the detergent drawer.
Fill the insert with detergent no further than the
Max
“
” mark and run the programme in the normal
way.
Detergent drawer with 4 chambers.
11
LIQUID BLEACH (HYPOCHLORITE)
Laundry with heavy stains may be
PRE-BLEACHED in the machine prior to carrying
out a normal wash programme. Proceed by
diluting the bleach in approximately 1l water
outside of the washing machine in a small
container.
For a machine with temperature selector:
• Turn the programme selector to programme 4.
• Turn the temperature selector to Min.
Warning: Bleaching is only possible in a cold
wash, otherwise your laundry and your applianc e
will be damaged.
For a machine without temperature selector:
• Turn the programme selector to programme 5.
• Press the special option button “cold wash”
(if available).
DYEING
Commercially available products usually consist
of a dye colour, fixing agent and salt.
Pour the dye colour, fixing agent and salt directly
into the empty drum, and only then load the
laundry.
REMOVING THE FILTER
Warning: Bleaching is only possible in a cold
wash, otherwise your laundry and your appliance
will be damaged.
Poor the diluted bleach into chamber and start
the machine.
After this prebleach wash, do a normal wash, in
which more not bleachable laundry can be adde d.
Add detergent into chamber and start a wash
programme. For this subsequent wash a lower
temperature wash programme (for example 40°C)
can be sufficient because of the pre-bleach
treatment. In this way energy can be saved.
Note:
Bleach should only be used with bleachable
fabrics
• Only use products designed for use in
washing machines.
• Follow the manufacturer’s instructions.
• Plastic and rubber components of the
machine can be stained by dyes.
WHEN TO REMOVE THE FILTER
• Check and clean the filter at least 2 or 3 times
a year.
• When the appliance does not drain or spin
properly.
• When the pump is blocked by an object
(buttons, coins, safety pins).
Important: Make sure that the water has
cooled before draining.
REMOVING THE FILTER
1. Switch off the appliance.
Open the filter cover with a coin
2.
3. Place a tray or container beneath the cover.
4.
Slowly turn the filter anticlockwise without
unscrewing it completely.
5. Wait until all the water has drained off.
Now unscrew the filter completely and
6.
remove it.
7. Remove any foreign material from the filter.
8. Check that the pump rotor moves freely.
9. Insert the filter and screw it in clockwise until
it locks.
10.Pour 1/2 litre of water into the detergent
drawer and check that water does not leak
from the filter.
11.Close the cover.
2
6
4
12
DRAINING RESIDUAL WATER
WHEN TO DRAIN RESIDUAL WATER
•
If the filter needs to be cleaned during a
programme.
Note:
Make sure that the water has cooled
before draining.
Note:
There can be up to 20 litres of water in the
machine.
•
When transporting or moving the machine.
•
If there is danger of freezing in the installation
room. In this case the machine and the hoses
should be drained after every wash.
DRAINING RESIDUAL WATER
1.
Switch off the appliance.
2.
Unplug the machine from the mains.
3.
Unclip the drain hose connection on the rear
part of the machine (see arrow).
4.
Lower the drain hose into a container and let
the water drain.
Note:
Make sure that the water has cooled
before draining.
WASHING MACHINE INSTALLED IN ROOM
EXPOSED TO FREEZING TEMPERATURES
5.
Wait until the flow stops.
Note:
There can be up to 20 litres of water in th e
machine during a programme.
6.
Clip the drain hose again on the rear part of
the machine.
7.
Replace the drain hose with the “U” bend and
fix it.
Drain residual water from the machine, and
the inlet hose after every wash cycle.
1.
Switch off the appliance.
2.
Unplug the machine from the mains.
3.
Close the tap, loosen the inlet hose from the
machine and let the water drain out.
4.
Open the filter, let the water drain out and
close it again.
Note:
Before a new wash cycle screw the inlet
hose to the machine by hand. Check watertightness of washing machine connections by
turning the tap completely on.
13
CARE AND MAINTENANCE
APPLIANCE EXTERIOR AND CONTROL
PANEL
•
Clean using normal household detergent
(do not use abrasive products).
•
Dry with a soft cloth.
Do not use petrol or petroleum products to clean
plastic parts.
DETERGENT DRAWER
Disengage the drawer by pressing down the
1.
release lever and extract it.
Remove the inserts (the siphon from the
2.
softener compartment and the insert for liquid
detergent).
3.
Wash all the parts under running water.
4.
Reposition the inserts, fit in the drawer until
it locks.
DOOR SEAL
•
Clean with a damp cloth when necessary.
•
Check the seal folds for foreign bodies
periodically.
WATER HOSE MESH FILTER
•
Check and clean periodically
1.
Turn off the tap.
2.
Unscrew the hose from the tap.
3.
Remove the mesh filter and clean it.
4.
Refit the filter and screw the hose connection
to the tap.
5.
Unscrew the hose from the machine.
6.
Remove the filter from the washing machine
with pliers and clean it.
7.
Replace the filter and screw the hose
connection back on to the machine.
8.
Turn on the tap and ensure that the
connections are completely water-tight.
2
1
Detergent drawer with 3 chambers
Detergent drawer with 4 chambers
APPLIANCE FILTER
•
Check the filter at least two or three times a
year and clean if necessary (see “Removing
the Filter”).
14
TROUBLESHOOTING GUIDE
The appliance will not switch on.
Power plug properly inserted in mains
•
socket?
Mains fuse OK?
•
Power failure?
•
Tap turned on? Is water coming through?
•
Door closed?
•
Programme selected?
•
Appliance switched on?
•
No water or insufficient water supply.
Tap turned on completely?
•
Kink in water hose?
•
Water hose filter clogged (see “Care and
•
Maintenance”)?
Water hose frozen up?
•
Waste water not pumped out.
Drain hose installed correctly (see
•
“Installation”)?
Filter clogged (see “Removing the filter”/
•
“Draining residual water”)?
Drain hose frozen up?
•
Is the rinse hold button pressed?
•
AFTER-SALES SERVICE
Detergent and additive product residues in
detergent drawer at end of wash.
Siphon installed correctly?
•
Siphon clogged?
•
Not enough water delivered (see above)?
•
Also see “Detergent and Additives” and
•
“Care and Maintenance”.
Machine vibrates during spin cycle.
Machine perfectly horizontal with all four feet
•
on ground (see “Installation”)?
Transit screws and bar removed? The transit
•
screws and bar must be removed before the
machine is used (see “Installation”).
Final spin results are poor.
Pump impeller obstructed (see “Removing
•
the filter”/“Draining residual water”)?
Before contacting After-Sales Service:
Try to remedy the problem
1.
(see “TroubleShooting Guide”).
Restart the programme to see if the fault is
2.
repeated.
If the malfunction persists, call After-Sales
3.
Service and specify:
The nature of the problem.
•
The exact model of the appliance.
•
The service code
•
(number after the word SERVICE).
The After-Sales Service sticker is on the inside
of the door.
Your full address.
•
Your telephone number and area code.
•
The After-Sales Service telephone number
•
and address can be found in the warranty or
on application to the retailer.
15
Loading...