Whirlpool ESZ 5469 IN, ELZ 6260/AL, ESZ 5963 IN, AKZ 614/IX, ESNA 4463/B WS INSTALLATION Manual

...

Whirlpool ESZ 5469 IN, ELZ 6260/AL, ESZ 5963 IN, AKZ 614/IX, ESNA 4463/B WS, EMZ 5469 IN, ESN 5468 IN, ESZ 5960 IN, ESN 5761 WS, ESZ 5864 WS, ESZB 5860 SW, ESZB 5860 IN, EMZH 5963 IN, ESZ 5761 IN, OBU A40 W, ESZ 5761 SW, ESZH 4866 IN, ESZB 5863 IN, ESZ 5864 IN, ELZ 6160 IN, ESZ 5761 WS, ESZB 5863/01 IN, EMZH 5964 BR, ESN 5761 SW, ESZ 5864 BR, EMZ 4460/A SW, EMZH 5964 WS, EMZ 4460/A WS, ELZD 4966 AL, ESZH 4866 AL, AKP 356 WH, ESZH 5960 SW, ESZA 5863 IN, ESZ 4463/B IN, ELZE 6164 IN, ELZE 5163 IN, ESN 4463/B SW, AKZ 612/01 NB, ESZH 5960 AL, ESZH 5963/BR/01, EMZD 4866 AL, ELZD 6265/BR, EMZD 4866 IN, EMZD 5262/IN, AKZ 224/AV, ESN 5761 BR, ESZ 8469 WS, EMZH 5863 IN, EMZ 8469 SW, ELZM 8469 IN, ESN 8468 WS, ESZ 8469 SW, AKZ 648/IX, ELZD 5969 IN, ESZ 8469 IN, ESZ 8468 SW, ESN 5468 SW, ESN 8469 SW, EMZ 8469 WS, ELZ 6260 SW, EMZ 6260 IN, EMZ 5969 IN, EMZ 6265/IN, ESZB 5860 BR, ELZ 6160 IN-1, ELZE 6160 IN, EMZ 6263/IN, EMZ 5262 WS, ELZD 5263 IN, ESZB 5860 WS, AKZ 612/NB/02, ESN 5761 IN, AKZ 612/01 AV, AKZ 612/01 AL, EMZ 5262 IN, ESZ 5961 WS, AKZ 225/IX, ESN 5960 WS, ESZH 5963 BR, EMZ 6263 IN-1, ESZH 5963 IN, AKZ 225/WH, EMZD 5266/BR, ESZ 5961 IN, EMZD 6263 IN, ESZ 5761 BR, EMZ 6262/WS, ESZH 5963/WS/01, ELZE 6163 IN, ELZD 6263 IN, ESZ 5761 AL, ELZ 6260 IN, EMZ 8469 IN, ESN 8469 IN, ESN 5961/SW, ELZD 4966 IN, EMZD 5266 PT IN, EMZD 5263 WS, ESN 5960 IN, EMZD 5263 IN, ELZD 6264/IN, AKZ 612/AL/02, ELZ 7260 IN, AKZ 205/IX, AKZ 612/IX/02, AKZ 612/WH/02, AKZ 612/WH/01, ELZE 7260 IN, ESZ 5964 IN, AKZ 532 WH, ESZ 5960 BR, AKZ 205/AV, ESZH 5863 WS, AKZ 613/IX, ESZH 5950 IN, ESZ 5960 SW, ESZ 5960 AL, ESZB 5960 WS, ESZB 5960 IN, EMZA 5963 IN, ELZD 6265/WS, EMZ 5262 BR, ESN 5961/WS, EMZ 5264 IN, ELZD 5264 IN, ESN 5960 BR, ESZ 5961 SW, ESN 8469 WS, ESZ 5969 SW, ESZH 5863 IN, ELZM 6160 IN, ESN 5468 WS, ESZH 5863 BR, AKZ 649/IX, EMZD 6265/IN, AKZ 400/IX/05, EMZ 6262/IN, ELZM 7260 IN, ESZH 5963/IN/01, EMZA 4460/A WS, EMZD 6260 IN, AKZ 612/01 IX, ESZ 5962 IN, EMZD 5263 BR, OBU B40 S, ELZE 6160 AL, ELZ 6260 WS, EMZ 5263 IN, ESZH 5964 IN, ESN 6260 IN, OBU C40 S, EMZ 4460/A IN, ESZ 5964 BR, ESN 5961/IN, ESZ 5960 IX, EMZA 4460/A IN, EMZH 5964 IN, ESZ 4463/B SW, EMZD 5266 IN, ESZ 4463/B WS, ESN 4463/B WS, EMZD 5266 WS, EMZD 6260/AL, ESN 5868 WS, AKZ 532 IX, ESZH 5960 BR, AKZ 288/IX, EMZ 5960 IN, EMZ 5469 SW, ESZB 5863 WS, ESZ 5469 SW, EMZ 5469 WS, ELZD 6265/IN, EMZD 6265/BR, EMZD 6265/WS, AKZ 616 AV, AKZ 501 WH, EMZ 6264/IN, ESZB 5863 BR, ESZ 5964 WS, ESZH 5960 WS, ESZH 5963/WS, EMZD 6262/IN, ESZ 5469 WS, EMZ 5960 WS INSTALLATION Manual

10200153aGB.fm Page 3 Monday, September 5, 2005 3:27 PM

INSTALLING THE UNDER THE COUNTER OVEN

Recommendations

Important: Disconnect the oven from the mains before carrying out any installation work or servicing.

Installation must be carried out by a qualified

•

electrician in accordance with the manufacturer's instructions and in compliance with local regulations.

Unpack the oven and make sure that the

•

appliance has not been damaged during transport and that the oven door closes properly.

are not sure contact the dealer or the nearest service centre.

After removing the oven from its packaging,

•

leave it on the polystyrene base to prevent it from being damaged.

When installing the oven it is advisable to wear

•

protective gloves. Do not lift the oven by the door handle. Get hold

•

of it using the side openings provided.

If you

Preparing the housing unit

Built-under oven

Kitchen units in contact with the oven must be

•

heat resistant (80 °C min). Cut the kitchen unit and worktop to fit before

•

installing the appliances. Carefully remove any shavings or sawdust that could prevent the appliances from running properly.

The dimensions of the oven and unit are shown

•

in figures 1-2-3. To allow for proper ventilation, an opening

•

should be left at the bottom of the housing unit. Pay attention to the dimensions in fig.3.

Leave a minimum clearance of 5 mm between

•

the upper edge of the oven and the lower edge of the worktop (fig. 2)

never be obstructed.

When installing, make sure that the sides of the

•

oven do not touch the adjacent units. If the kitchen unit is not securely fixed to the wall,

•

it must be anchored with standard brackets (G) available on the market, see fig. 3.

This clearance must

Cooktop Attention:

surface made of material other than wood (marble, plastic, ceramic, stone, etc.) remember to ask After Sales Service for the fixing plates (fig. 6-8).

The cooktop must be fitted in a worktop with a

•

minimum thickness of 20 mm and a maximum of 50 mm.

There must be nothing between the cooktop and

•

the oven (e.g. cross rails, insulating material, etc.). An adjacent column unit must be installed at le ast

•

100 mm from the edge of the cooktop (fig. 4). Cut an opening in the worktop of the dimensions

•

shown on the Product Description Sheet provided with the worktop.

We recommend you seal the internal edges of

•

the worktop with wood glue or silicone. If not already in place, apply the supplied seal to

•

the cooktop, after cleaning the adhesive surface thoroughly.

Conventional electric cooktop Important: Remove any protective film before

installing the cooktop.

• If the worktop is made of wood, use the spring clips and screws provided.

• If the worktop is made of marble or other material (plastic, ceramics, stone, etc.)

cooktop must be secured with special brackets (C) (fig. 6), Code 4819 310 18528, (available as a complete set from After Sales Service).

when installing the cooktop on a

Insert the 4 spring clips (B) (fig. 5) in their guides on the bottom of the cooktop.

Fit the cooktop into the worktop.

, the

Fasten the brackets into the holes with the screws provided.

Fit the cooktop into the worktop.

Glass-ceramic cooktop

Important: Remove any protective film before installing the cooktop.

Make sure that that the opening in the worktop for the cooktop is cut according to the dimensions given in the drawing on the Product Description Sheet. Pay attention to the tolerance range.

The cooktop should not be forced into the worktop. Forcing the glass-ceramic top may cause it to crack (even at a later date)!

10200153aGB.fm Page 4 Monday, September 5, 2005 3:27 PM

• If the worktop is made of wood

clips and screws provided.

Secure the spring clips (D) (fig. 7) with the screws provided (E) (fig.7) as shown, paying attention to the specified distances.

Fit the cooktop into the worktop.

• If the worktop is made of marble, plastic, ceramics, stone, etc.

secured with special brackets (F) (fig. 8), Code 4819 404 78697, available from After Sales Service.

Fit the cooktop into the worktop.

Place the 4 brackets (F) in position in accordance with the thickness of the worktop as shown in fig. 8.

Fasten the 4 screws (G) in the positions (H) (fig. 8).

, the cooktop must be

, use the spring

Electrical connection

• Regulations require that the appliance be earthed.

•

Connection to the mains must be carried out by a qualified electrician in accordance with the manufacturer's instructions and in compliance with local regulations.

•

The installer is responsible for connecting appliances correctly to the mains and for observing the safety regulations.

•

The oven power cable must be long enough to connect the built-in appliance to the mains.

•

Observance of safety directives requires that a multi pole switch with a minimum contact gap of 3 mm be used for the installation.

•

Do not use multiple plug adapters or extension leads.

•

After the oven has been installed, the electrical components must be inaccessible.

Connecting the oven to the power supply

•

Make sure that the voltage indicated on the rating plate is the same as the mains voltage. The rating plate is on the front edge of the oven (visible when the door is open).

•

Remove the two fastening screws of the terminal box cover (if supplied) located on the bottom part of the oven's rear covering. Remove the cover to gain access to the terminal box and insert the power cable (see table) through the opening located on the bottom of the oven. Connect the cable to the terminal box and secure it to the cable fastener. Put the cover back on by inserting the two blades in the slots and fasten it with the two screws.

Power supply cables table

N° of conductors Type of cable 1N+

2+ 2N+ 3N+ 3+

~ ~ ~ ~ ~

H05 RR-F 3 X 4 mm² H05 RR-F 3 X 4 mm² H05 RR-F 4 X 2.5 mm² H05 RR-F 5 X 1.5 mm² H05 RR-F 4 X 2.5 mm²

Interconnecting cooktop and oven

Important: do not connect the oven to the power supply before you have finished connecting the oven and cooktop.

•

Before connecting the oven to the power supply, make sure that the cooktop is among the ones listed in the cooktop/oven pairing product sheet provided.

•

Connect the two male 3 pole (H) (fig. 9) and 4 pole (J) (fig. 9) connectors of the cooktop to the respective female connectors located on the right hand side of the top covering of the oven.

•

Unscrew the nut of the ground screw (K) (fig. 9)

on the left hand side of the top covering of the oven and insert the yellow/green earth cable, leaving the washer in place.

•

Screw the nut back onto the screw and tighten it as far as it will go.

Securing the oven

•

Lift the oven getting hold of it by the openings on the sides and insert it into the housing unit, being careful not to trap the power supply cable (fig. 10).

•

Center the oven in the housing unit before securing it.

•

Make sure that the plastic spacers (if provided) are positioned correctly in the fastening holes. Then anchor the oven to the housing unit with the screws provided.