How it Works
Whirlpool
Loading...
ED5NHGXNT00
Owner’s Manual
56 pgs9.32 Mb0
User Manual
44 pgs1.16 Mb0

Whirlpool ED5NHGXNT00, ED5NHAXNL01, ED5NHGXNQ00, ED5NHEXNQ00, ED5NHEXNL00 Owner’s Manual

...
TABLEOFCONTENTS
TABLEDESMATIERES
REFRIGERATOR SAFETY ............................................................. 3
Proper Disposal of Your Old Refrigerator .................................... 3
INSTALLATION INSTRUCTIONS .................................................. 4
Unpacking .................................................................................... 4
Location Requirements ................................................................ 4
Electrical Requirements ............................................................... 5
Water Supply Requirements ........................................................ 5
Base Grille .................................................................................... 5
Door Removal ............................................................................... 6
Door Closing ................................................................................. 8
Water Supply Connection ............................................................ 8
Water System Preparation ......................................................... 10
Normal Sounds .......................................................................... 10
REFRIGERATOR USE .................................................................. 10
Ensuring Proper Air Circulation .................................................. 10
Using the Controls ..................................................................... 11
Water and Ice Dispensers .......................................................... 11
Water Filter Status Light ............................................................. 13
Water Filtration System .............................................................. 13
Ice Maker and Storage Bin ........................................................ 14
REFRIGERATOR FEATURES ...................................................... 15
Refrigerator Shelves ................................................................... 15
Flip-up Shelf ............................................................................... 16
Adjustable Flip-up Shelf ............................................................. 16
Drop-down shelf ......................................................................... 16
Dell Drawer ................................................................................. 16
Convertible Vegetable/Meat Drawer, Crisper and Covers ........16
Convertible Vegetable/Meat Drawer Temperature Control .......17
Crisper Humidity Control ........................................................... 17
Wine or Can/Bottle Rack ........................................................... 17
Utility Bin .................................................................................... 17
FREEZER FEATURES .................................................................. 18
Freezer Shelf .............................................................................. 18
Freezer Basket or Bin ................................................................. 18
DOOR FEATURES ........................................................................ 18
Tilt-out Freezer Door Bin............................................................ 18
Chilled Door Bin ......................................................................... 18
Door Rails ................................................................................... 19
Door Bins.................................................................................... 19
REFRIGERATOR CARE ............................................................... 19
Cleaning ...................................................................................... 19
Changing the Light Bulbs ........................................................... 20
Power Interruptions .................................................................... 21
Vacation and Moving Care ......................................................... 21
TROUBLESHOOTING .................................................................. 22
ASSISTANCE OR SERVICE ......................................................... 24
In the U.S.A ................................................................................ 24
In Canada ................................................................................... 25
Accessories ................................................................................ 25
WATER FILTER CERTIFICATIONS ............................................. 25
PRODUCT DATA SHEETS ........................................................... 26
WARRANTY .................................................................................. 27
SI:!:CURITE DU RI:!:FRIGERATEUR .............................................. 2g
Mise au rebut de votre vieux refrigerateur ................................. 29
INSTRUCTIONS D'INSTALLATION ............................................. 30
Deballage .................................................................................... 30
Emplacement d'installation ........................................................ 30
Specifications electriques .......................................................... 31
Specifications de I'alimentation en eau ..................................... 31
Grille de la base .......................................................................... 31
Enlevement des portes ............................................................... 32
Fermeture des portes ................................................................. 34
Raccordement de la canalisation d'eau .................................... 34
Preparation du syst_me d'eau ................................................... 36
Sons normaux ............................................................................ 36
UTILISATION DU REFRIGI:!:RATEUR .......................................... 37
Pour s'assurer d'une circulation d'air appropriee ...................... 37
Utilisation des commandes ........................................................ 37
Distributeurs d'eau et de glagons .............................................. 38
Le temoin lumineux de I'etat du filtre heau ............................... 40
Systeme de filtration d'eau ........................................................ 40
Machine a gla9ons et bac d'entreposage ................................. 41
CARACTI:!:RISTIQUES DU REFRIGERATEUR ........................... 42
Ctag_re inclinable ....................................................................... 43
Tiroir a legumes/viande convertible,
bac a legumes et couvercles ..................................................... 43
Reglage de la temperature du tiroir
legumes/viande convertible ....................................................... 44
Reglage de I'humidite darts le bac a legumes ........................... 44
Casier a vin ou porte-cannettes/bouteilles ................................ 44
Casier utilitaire ............................................................................ 45
CARACTI:!:RISTIQUES DU CONGELATEUR ............................... 45
Panier ou bac de congelateur .................................................... 45
CARACTI:!:RISTIQUES DE LA PORTE ......................................... 45
Compartiment inclinable de la porte du congealateur .............. 45
Compartiment frafcheur ............................................................. 46
Balconnets dans la porte ........................................................... 46
ENTRETIEN DU REFRIGI:!:RATEUR ............................................ 47
Nettoyage ................................................................................... 47
Remplacement des ampoules d'eclairage ................................ 48
Pannes de courant ..................................................................... 49
Entretien avant les vacances ou Iors d'un demGnagement .......49
DI!:PANNAGE ................................................................................. 50
ASSISTANCE OU SERVICE ......................................................... 53
FEUILLES DE DONNEES SUP LE PRODUIT ............................. 54
GARANTIE ..................................................................................... 55
REFRIGERATORSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance, Always read and obey all
safety messages.
This symbol alerts you to potential hazards that can kill or hurt you and others, All safety messages will follow the safety alert symbol and either the word "DANGER" or
This is the safety alert symbol, "WARNING," These words mean:
You can be killed or seriously injured if you don't immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed,
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic
precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all panels before operating.
• Remove doors from your old refrigerator.
• Use nonflammable cleaner.
• Keep flammable materials and vapors, such as gasoline, away from refrigerator.
• Use two or more people to move and install refrigerator.
• Disconnect power before installing ice maker (on ice maker kit ready models only).
• Use a sturdy glass when dispensing ice or water (on some models).
SAVE THESE INSTRUCTIONS
ProperDisposalofYourOld Refrigerator
Suffocation Hazard
Remove doors from your old refrigerator. Failure to do so can resuJt in death or
brain damage.
IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous
- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help
prevent accidents.
Before you throw away your old refrigerator or freezer:
• Take off the doors,
• Leave the shelves in place so that children may not easily
climb inside,
INSTAILATIONINSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
Removing packaging materials
• Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see the "Refrigerator Safety" section.
When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pulI the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move
it, as floor damage could occur.
Cleaning before use
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions in the "Refrigerator Care" section.
important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many smal!, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when re- moving them to avoid impact from dropping.
E×ploeion Hazard
Keep flammabJe materiaJs and vapors, such as gasoline, away from refrigerator.
Failure to do so can result in death, explosion,
or fire.
To ensure proper ventilation for your refrigerator, allow for 1/2in. (1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2 in. (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.
NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location where the temperature will fall below 55°F (13°C).
_Jl,
/
/
/,
V2" (1.25 crn)
II -- 1
/
2" (5o08 cm)
ElectricaJ Shock Hazard
Plug into a grounded 3 prong outJet.
Do not remove ground prong. Do not use an adapter.
Do not use an extension cord. Failure to follow these instructions can reeuJt in
death, fire, or electrical shock.
Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical
connection.
Recommended grounding method
A 115 Volt, 60 Hz., AC only 15 or 20 amp fused, grounded
electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord. NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.
Read all directions carefully before you begin.
IMPORTANT:
• If you turn the refrigerator on before the water line is connected, turn the ice maker OFR
• All installations must meet local plumbing code requirements.
• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.
Tools Required: Flat-blade screwdriver, 7_6in. and 1/2in. open-
end wrenches or two adjustable wrenches, 1/4in. nut driver and drill bit, hand drill or electric drill (properly grounded).
NOTE: Your refrigerator dealer has a kit available with a 1/4in. (6.35 ram) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3/16in.
(4.76 mm) saddle valve which reduces water flow and clogs more easily.
Water Pressure
A cold water supply with water pressure of between 30 and 120 psi (207-827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, see "Troubleshooting" or call a licensed, qualified plumber.
Reverse Osmosis Water Supply If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).
If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 - 414 kPa) a booster pump can be inserted into the small tubing that goes from the cold water line to the reverse osmosis system.
If the water dispenser is still not dispensing water properly:
• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis system to refill after heavy usage.
If your refrigerator has a water filter cartridge, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge. See "Water Filtration System."
If you have questions about your water pressure, refer to "Troubleshooting" or call a licensed, qualified plumber.
To remove the base grille:
1. Open both doors.
2. Place hands along the ends of the grille. Push in on the top and pull up on the bottom.
NOTE: Be sure to refasten the Tech Sheet behind the base grille after cleaning.
To replace the base grille:
1. Open both doors.
2. Line up the grille support tabs with the metal clips.
3. Push the grille firmly to snap it into place.
TOOLSNEEDED:1/4in.hex-headsocketwrench,%6in.hex-headsocketwrenchandaflat-bladescrewdriver.
IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFEUnplugrefrigeratorordisconnectpower.Removefoodandany adjustabledoororutilitybinsfromdoors.
NOTE:Itmayonlybenecessarytoremoveeitherthedoorhandleorthedoorstogetyourproductthroughthedoorwayofyourhome. Measurethedooropeningtoseewhetheryouneedtoremovetherefrigeratorhandlesorthedoors.
Electrical Shock Hazard
Disconnect power before removing doors. Reconnect both ground wires before operating. Failure to do so can result in death or electrical shock.
Top Left Binge
Style 1
Style 2
1. Do Not Remove Screw
Water Dispenser Tubing Connection
Top Right Binge
1
1. Do Not Remove Screw
Handte RemovaJ
(OptionaJ)
1, Red Outer Ring
I
1
Door Alignment
\
1. Leveling Screw
Bottom Binge
1, Do Not Remove Screw
Handle Removal (optional)
Style 1
1. Apply firm pressure with your hand on the face of trim. Slide
top trim up and bottom trim down away from handle. Lift trim pieces off shoulder screws (see Graphic 1).
NOTE: Some models include accent pieces between the handle and the handle trim. If your model includes the accents, you will need to carefully remove them with a flat-blade screwdriver before removing the handle screws. The accent pieces are optional and can be reinstalled or left off the handle assembly.
2. Remove handle screws and handles. (See Graphic 1).
3. Move refrigerator into place. Replace handles as shown (see Graphic 1).
Style 2
1. Apply firm pressure on the handle to slide it up and off of the shoulder screws (see Graphic 1).
2. Move refrigerator into place. Replace handles as shown (see Graphic 1).
Door Removal
6. Disconnect wiring:
Style 1
• Disconnect wiring plug.
• Remove green ground wire screw to disconnect ground wires.
1.Donot remove screw 1
2. Ground wires
3. Green ground wire screw
4. Wiring Plug
Style 2
• Disconnect wiring plug.
E_ectrica_ Shock Hazard
Disconnect power before removing doors. Failure to do so can result in death or
etectrica_ shock.
1. Unplug refrigerator or disconnect power.
2. Open both refrigerator doors. Remove the base grille by pulling up on the bottom outside corners (see Graphic 2).
3. Close both doors and keep them closed until you are ready to lift them free from the cabinet.
4. If you have a dispenser (ice or water), disconnect the water dispenser tubing located behind the base grille on the freezer
door side (see Graphic 3).
• Press the red outer ring against the face of the fitting and
pull the dispenser tubing free.
• On some models, remove the tubing from the hose clip.
5. Remove the top left hinge cover and screws as shown (see Graphic 4). Do not remove screw 1.
!. Do not remove screw 1
2. Wiring plug
7. Carefully lift the freezer door straight up and off of the bottom hinge (see Graphic 5). The water dispenser tubing remains attached to the freezer door and pulls through the bottom left hinge. Make sure you protect the dispenser tubing from damage.
8. Remove the top right hinge cover and screws as shown (see Graphic 6). Do not remove screw 1.
9. Lift the refrigerator door straight up and off of the bottom hinge.
10. It may not be necessary to remove the bottom hinge to move the refrigerator through a doorway. Both bottom hinges have similar construction. If necessary, disassemble the hinges as shown (see Graphic 7). Do not remove screw 1.
Door and Hinge Replacement
1. Replace both bottom hinges, if removed. Tighten screws.
2. Assistance may be needed to feed the water dispenser tubing through the bottom hinge while reinstalling the freezer door. Carefully feed the dispenser tubing through the bottom left hinge before replacing the door on the hinge.
NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.
3. Reconnect water dispenser tubing by pushing tubing into fitting until it stops and black mark touches face of fitting (see Graphic 3). On some models, replace tubing in hose clip.
4. Alignandreplacethetoplefthingeasshown(seeGraphic4). Tightenscrews.
ElectricaJShockHazard
Reconnectbothgroundwires. Failuretodosocanresultindeathor
etectricaJshock.
Style1
• Reconnectbothgroundwires.
• Reconnectwiringplug.
1
/
/
Your refrigerator has two front adjustable rollers -- one on the right and one on the left. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:
1. Move the refrigerator into its final position.
2. The two leveling screws are part of the front roller assemblies, which are at the base of the refrigerator on either side (see Graphic 8).
3. Use a hex-head socket wrench to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator (see Graphic 8).
NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.
4. Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.
5. Replace the base grille.
NOTE: Be sure to refasten the Tech Sheet behind the base grille.
!. Do not removescrew 1
2. Ground wires
3. Greenground wirescrew
4. Wiringplug
Style 2
• Reconnect wiring plug.
1.Do not remove screw 1
2. Wiringplug
5. Replace left hinge cover and screws.
6. Replace the refrigerator door by carefully lifting the door onto the bottom right hinge.
7. Align and replace the top right hinge as shown (see Graphic 6). Tighten screws.
8. Replace hinge cover and screws. Tighten screws.
9. Plug into a grounded 3 prong outlet.
Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line
is connected, turn the ice maker OFR
Connecting to Water Line
1.
Unplug refrigerator or disconnect power.
2.
Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.
Locate a 1/2in. to 11/4in. (1.25 cm to 3.18 cm) vertical COLD water pipe near the refrigerator.
NOTE: Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.
Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use 1/4in. (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.
Using a grounded drill, drill a 1/4in. hole in the cold water pipe you have selected.
.......... 1
7 ......................2
1.Cold waterpipe 5. Compression sleeve
2. Pipe clamp 6. Shutoff valve
3. Copper tubing 7.Packing nut
4. Compression nut
6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4in. drilled hole in the water pipe and that the washer is under the pipe clamp, Tighten the packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the copper tubing as shown, Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and turn ON the main water supply, Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.
Connecting to Refrigerator
Style 1
1. Unplug refrigerator or disconnect power.
2. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut, Do not overtighten.
3. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.
!
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.
3. Thread the provided nut onto the coupling on the end of the copper tubing. Tighten the nut by hand, Then tighten it with a wrench two more turns. Do not overtighten.
i 2 3 4 5
1.Line torefrigerator 4. Coupling (provided)
2. Nut (provided) 5. Ferrule (purchased)
3. Bulb 6. Nut (purchased)
4. Turn shutoff valve ON,
5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.
6. The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4in, (6.35 mm) water line at either tube connection, Obtain a water strainer from your nearest appliance dealer.
7. Plug in refrigerator or reconnect power.
8. Flush the water system. See the "Water System Preparation" section,
NOTE: Allow 24 hours to produce the first batch of ice, Allow 3 days to completely fill ice container.
Style 3
1. Unplug refrigerator or disconnect power.
2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.
3. Thread the provided nut onto the water valve as shown,
1. Tube clamp
2. Copper tubing
3. Compression nut
4. Valve inlet
6. The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4in. (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.
7. Plug in refrigerator or reconnect power.
8. Flush the water system. See the "Water System Preparation" section.
NOTE: Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill ice container.
1
2
1. Bulb
2. Nut (provided)
NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.
4. Turn shutoff valve ON,
5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak,
6. The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4in, (6.35 mm) water line at either tube connection, Obtain a water strainer from your nearest appliance dealer.
7. Plug in refrigerator or reconnect power.
8. Flush the water system. See the "Water System Preparation" section,
NOTE: Allow 24 hours to produce the first batch of ice, Allow 3 days to completely fill ice container.
Pleasereadbeforeusingthewatersystem. Immediatelyafterinstallation,followthestepsbelowtomake
surethatthewatersystemisproperlycleaned.
1. Openthefreezerdoorandturnofftheicemaker.ForStylef, liftupthewireshutoffarmasshown.ForStyle2,movethe switchtotheOFF(right)settingasshown.TheON/OFF switchislocatedonthetoprightsideofthefreezer compartment.
Style I
Style 2
Your refrigerator is designed to run more efficiently to keep your food items at the desired temperatures and to minimize energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.
• You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan speed may increase as you open the doors or add warm food.
• Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.
• Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.
• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.
• Contraction and expansion of the inside walls may cause a popping noise.
• You may hear air being forced over the condenser by the condenser fan.
• You may hear water running into the drain pan during the defrost cycle.
REFRIGERATORUSE
NOTES:
• If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position.
• Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before or after the system.
2.
Use a sturdy container to depress the water dispenser bar until the water begins to flow. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of the dispenser.
3.
Open the freezer door and turn on the ice maker. For Style 1, lower the wire shutoff arm. For Style 2, move the switch to the ON (left) position. Please refer to the "Ice Maker and Storage Bin" section for further instructions on the operation of your ice maker.
• Allow 24 hours to produce the first batch of ice.
• Discard the first three batches of ice produced.
• Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.
Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard surfaces, such as the floor, walls, and cabinets, can make the
sounds seem louder. The following describes the kinds of sounds and what may be making them.
• If your product is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.
In order to ensure proper temperatures, you need to permit air to flow between the two sections. Cold air enters the bottom of the
freezer section and moves up. It then enters the refrigerator section through the top vent. Air then returns to the freezer as
shown.
/
Do not block any of these vents with food such as soda, cereal, bread, etc. If the vents are blocked, airflow will be prevented and the temperature controls will not function properly.
IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent odor transfer from food, wrap or cover foods tightly.
10
/iiY !iiii ii!iii!ilt:!:i;C iiii:: i!
For your convenience, your refrigerator controls are preset at the
factory. When installing your refrigerator, make sure that the
controls are still preset to the "mid-settings" as shown.
Style I
FREEZER
COLD
COLDER COLD
Style 2
IMPORTANT:
• Your product will not cool when the Refrigerator Control is set to OFR
The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Control adjusts the freezer compartment temperature. Higher numbered settings make the compartment colder. Lower numbered settings make the temperature less cold.
• Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your food may spoil.
NOTE: Adjusting the Refrigerator and Freezer Controls to a higher (colder) setting will not cool the compartments any
faster.
• The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.
• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.
REFRRGERATOR
I
. 3 4 ,
1 6 COLDER
3. Push the control in to lock it into place. CONDITION/REASON: SETTING
ADJUSTMENT:
REFRIGERATOR too cold REFRIGERATOR Not set correctly for your
Control one setting
conditions lower REFRIGERATOR too warm REFRIGERATOR
Door opened often, large amount of Control one setting food added or room temperature higher
very warm FREEZER too cold FREEZER Control one
Not set correctly for your setting lower conditions
FREEZER too warm/too little ice FREEZER Control one Door opened often, or large amount setting higher
of food added or very cold room temperature (can't cycle often enough) or heavy ice usage
Cut Hazard
Use a sturdy g(ass when dispensing ice or water.
Fai)ure to do so can result in cuts.
Depending on your model, you may have one or more of the following options: the ability to select either crushed or cubed ice, a special light that turns on when you use the dispenser, a special Night Light mode, or a lock option to avoid accidental dispensing.
Adjusting the Controls
If you need to adjust temperatures, adjust the refrigerator
temperature first.
NOTE: Wait at least 24 hours between adjustments and then recheck the temperatures.
Style 1
Turn the control to the right (clockwise) to make the compartment
colder or to the left (counterclockwise) to make it less cold. Style 2
1. Push in on the control and release it.
2. The control will pop out. Turn the control to the desired setting.
The ice dispenser
Ice dispenses from the ice maker storage bin in the freezer. When the dispenser lever is pressed:
• A trap door opens in a chute between the dispenser and the ice bin. Ice moves from the bin and falls through the chute.
• When you release the dispenser lever, the trap door closes and the ice dispensing stops. The dispensing system will not operate when the freezer door is open.
11
Some models dispense both cubed and crushed ice. Before dispensing ice, select which type of ice you prefer. The button controls are designed for easy use and cleaning.
Style 1 Style 2
O
ICE
CRUSH CUBE
NOTE: Water may have an off-flavor if you do not use the
dispenser periodically. Dispense enough water every week to maintain a fresh supply.
The dispenser light
For crushed ice, cubes are crushed before they are dispensed.
This may cause a slight delay when dispensing crushed ice.
Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first cubes.
To dispense ice:
1. Press button for the desired type of ice.
2. Press a sturdy glass against the ice dispenser lever. Hold the glass close to the dispenser opening so ice does not fall outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to the lever in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.
3=
Remove the glass to stop dispensing. NOTE: The first few batches of ice may have an off-flavor
from new plumbing and parts. Throw the ice away. Also, take large amounts of ice from the ice bin, not through the dispenser.
The water dispenser
Style 1 The dispenser area has a light. It can be turned on manually by
pressing the ON button (touch pad or rocker switch). On some models: Whenever you use the dispenser the lever will
automatically turn the light on.
LIGHT
OFF O N
NOTE: See the "Changing the Light Bulbs" section for
information on changing the dispenser light bulb.
Style 2
When you use the dispenser, the lever will automatically turn the light on. If you want the light to be on continuously, you may
choose either ON or NIGHT LIGHT.
NIGHT
ON LIGHT
@
If you did not flush the water system when the refrigerator was
first installed, press the water dispenser bar with a glass or jar
until you draw and discard 2 to 3 gal. (8 to 12 L) or approximately 6 to 7 minutes of water after water begins dispensing. It will take 3 to 4 minutes for the water to begin dispensing. The water you draw and discard cleans the system and helps clear air from the lines. Allow several hours for the refrigerator to cool down and
chill water. IMPORTANT: Depending on your model, the small removable
tray at the bottom of the dispenser is designed to catch small
spills and allow for easy cleaning. There is no drain in the tray.
The tray can be removed from the dispenser and carried to the
sink to be emptied or cleaned.
To dispense water:
1. Press a glass against the water dispenser lever.
2. Remove the glass to stop dispensing.
ON: Press the LIGHT button to turn the dispenser light on. NIGHT LIGHT: Press the LIGHT button a second time to select
the Night Light mode. The dispenser light will automatically adjust to become brighter as the room brightens, dimmer as the
room darkens. OFF: Press the LIGHT button a third time to turn the dispenser
light off. The dispenser lights are LEDs which should not need to be
changed. If it appears that your dispenser lights are not working, check to be sure that the light sensor is not blocked (in Night Light mode). See "Troubleshooting" for more information.
The dispenser lock (on some models)
Your dispenser can be turned off for easy cleaning or to prevent accidental dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the product, to the ice maker, or to the dispenser light. It simply deactivates the dispenser levers.
12
Style 1
To turn off the dispenser, press the LOCK button until the
indicator appears. The ice and water dispensers will not work. To unlock the dispenser, press the UNLOCK button until the indicator appears. Then continue to dispense ice or water as
usual.
DISPENSER
LOCK UNLOCK
Non-Indicator Water Filter (on some models)
If your refrigerator does not have the water filter status light, you should change the water filter cartridge every 6 to 9 months depending upon your usage. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter cartridge more often.
Style 2
To turn off the dispenser, press and hold the LOCK OUT button
until the indicator appears. The ice and water dispensers will not work. To unlock the dispenser, press the LOCK OUT button until
the indicator disappears. Then continue to dispense ice or water
as usuaJ.
@
PRESS& HOLD
The water filter status light will help you know when to change your water filter cartridge. The light will change from green to yellow. This tells you that it is almost time to change the water filter cartridge (90% of the filter life has been used). It is
recommended that you replace the base grille water filter cartridge when the water filter indicator light changes to red OR water flow to your water dispenser or ice maker decreases noticeably. To change the base grille water filter cartridge, see "Changing the Water Filter Cartridge" later in this section.
After changing the water filter cartridge, reset the water filter
status light. Style 1
Press the light switch 5 times within 10 seconds. The status light will change from red to green.
1. Status light
2. Light switch
Style 2 Press and hold the water filter reset button until the status light
turns green. Your reset button may be located on the water
dispenser or on the control panel in the refrigerator compartment.
Dispenser Control Panel
NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
Changing the Water Filter Cartridge
Style 1: Behind the base grille filter
1. Remove the base grille (see "Door Removal" section). Rotate the cartridge counterclockwise to a vertical position and pull the filter cartridge out.
NOTE: There will be water in the cartridge. Some spilling may occur.
2. Take the new cartridge out of its packaging and remove protective cover from o-rings.
3. Push the new filter cartridge into the base until it stops. Rotate the cartridge clockwise to a horizontal position. Flush
the water system (see "Flushing the Water System After Replacing Filter" later in this section).
Style 2: Through the base grille filter
1. Locate the water filter cartridge cap in the front base grille. Rotate the cap counterclockwise to a vertical position and pull the cap and filter cartridge out through the base grille.
NOTE: There will be water in the cartridge. Some spilling may
occur.
2. Remove the cartridge cap by sliding it off the end of the old cartridge. The cap will slide to the left or right. DO NOT
DISCARD THE CAR
o •
PRESS& HOLD
13
3. Take the new cartridge out of its packaging and remove protective cover from o-rings.
4=
Slide the cartridge cap onto the new cartridge. See illustration in Step 2.
5.
With cartridge cap in the vertical position, push the new filter cartridge into the base grille until it stops. Rotate the cartridge cap clockwise to a horizontal position. Flush the water system (see "Flushing the Water System After Replacing Filter" later in this section).
Flushing the Water System After Replacing Filter
Use a sturdy container to depress the water dispenser bar until
the water begins to flow. Flush the water system by dispensing
and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some
households. NOTE: As air is cleared from the system, water may spurt out of
the dispenser.
Using the Dispenser Without the Water Filter
2. To manually turn the ice maker off, lift the wire shutoff arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.
MAX
©
\
To increase ice production rate:
Normal Ice Production: In normal ice production mode, the ice maker should produce approximately 7 to 9 batches of ice in a 24-hour period. If ice is not being made fast enough, turn the Freezer Control toward a higher (colder) number in half number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours between each increase.
Maximum Ice Production (on some models): In maximum ice production, the ice maker should produce approximately 10 to 14 batches of ice in a 24-hour period. If your refrigerator has the maximum ice production feature, push the switch to
MAX.
To remove and replace ice storage bin:
1. Pull the covering panel out from the bottom and then slide it back toward the rear.
2. Lift the wire shutoff arm so it clicks into the OFF (up) position. Ice can still be dispensed, but no more can be made.
3. Lift up the front of the storage bin and pull it out.
You can run the dispenser without a water filter cartridge. Your water will not be filtered.
1. Remove the base grille water filter cartridge. For Style 1, replace the base grille after removing the filter.
2. For Style 2, slide the cartridge cap off the end of the filter cartridge. DO NOT DISCARD THE CAR With the cartridge cap in the vertical position, insert the cap into the base grille until it stops.
3.
Rotate the cartridge cap to a horizontal position. The cartridge cap might not be even with the base grille.
:J ,
Style 1
To turn the ice maker on/off:
The on/off switch for the ice maker is a wire shutoff arm located
on the side of the ice maker.
1. To turn the ice maker on, simply lower the wire shutoff arm. NOTE: Your ice maker has an automatic shutoff. As ice is
made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.
Replace the bin by pushing it in all the way or the dispenser will not work. Push the wire shutoff arm down to the ON
position to restart ice production. Make sure the door is closed tightly.
Style 2
To turn the ice maker on/off:
The ON/OFF switch is located on the top right side of the freezer compartment.
1. To turn the ice maker on, slide the control to the ON (left) position.
NOTE: Your ice maker has an automatic shutoff. The ice maker sensors will automatically stop ice production, but the
control will remain in the ON (left) position. To manually turn the ice maker off, slide the control to the
OFF (right) position.
14
To remove and replace the ice storage bin:
1. Hold the base of the storage bin with both hands and press
the release button to lift the storage bin up and out, NOTE: It is not necessary to turn the ice maker control to the
OFF (right) position when removing the storage bin. The sensor cover ("flipper door") on the left wall of the freezer stops the ice maker from producing ice if the door is open or the storage bin is removed.
2. Replace the storage bin on the door and push down to make sure it is securely in place.
Clean the Ice Storage Bin
Empty the ice container. Use warm water to melt the ice if necessary.
NOTE: Never use anything sharp to break up the ice in the bin. This can cause damage to the ice container and the dispenser mechanism.
2. Wash ice bin with a mild detergent, rinse well and dry thoroughly. Do not use harsh or abrasive cleaners or solvents.
REFRIGERATOR
FEATURES
Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in the "Accessories" section.
_mportant information to know about glass shelves
and cov_ra:
Do not ciean glass sheives or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when re- moving them to avoid impact from dropping.
Your model may have glass or wire shelves. Store similar foods together and adjust the shelves to fit different heights. This reduces the time the refrigerator door is open and saves energy.
REMEMBER
• Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill ice container.
• Discard the first three batches of ice produced to avoid impurities that may be flushed out of the system.
• The quality of your ice will be only as good as the quality of the water supplied to your ice maker.
Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.
• It is normal for the ice cubes to be attached at the corners. They will break apart easily.
• For Style 1 ice maker, do not force the wire shutoff arm up or down.
• Do not store anything on top of the ice maker or in the ice storage bin.
Slide-out Shelves (on some models)
To remove and replace a shelf in a metal frame:
1. Pull the shelf forward to the stop. Tilt the front of the shelf up and lift it slightly as you pull the shelf from the frame.
2. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past the stop.
Shelves and Shelf Frames
To remove and replace a shelf/frame:
1. Remove the shelf/frame by tilting it up at the front and lifting it out of the shelf supports.
15
To raise or lower the shelf:
1. Raise the shelf by pulling forward on the lever located at the
bottom front of the shelf and lift until the shelf locks into the vertical position.
2. Lower the shelf until it is latched securely in place.
To raise or lower the shelf:
1. Raise the shelf by first sliding it back and down to make it half-width. (You can use the shelf in this position to allow taller items to be stored on the shelf below.)
2. Lift the front of the shelf until it fits securely in place against the back wall. Lower the shelf securely back into position.
3. Pull the front of the shelf forward until it fits into place.
2=
With the rear pegs released, pull the shelf down and forward. Replace the shelf by sliding the front pegs into the track.
3.
Push the shelf up and back until the rear pegs drop into the track. Pull down and forward to be sure the shelf is securely in place.
The dell drawer stores raisins, nuts, spreads, and other small items at normal refrigerator temperatures.
To remove and replace the deli drawer:
1. Remove the dell drawer by sliding it straight out to the stop. Lift the front and slide the drawer out the rest of the way.
Replace the dell drawer b sliding it back past the stop.
:i::ii
To remove and replace the drop-down shelf:
1. Remove the drop-down shelf by sliding it up and back. Pull forward slightly to release the rear pegs from the track as
shown.
Crisper and Convertible Vegetable Meat Drawers
To remove and replace drawers:
1. Slide crisper or meat drawer straight out to the stop. Lift the front of drawer with one hand while supporting the bottom of
drawer with other hand and slide the drawer out the rest of the way.
2. Replace the crisper or meat drawer by sliding it back in fully past the drawer stop.
Crisper or Vegetable/Meat Drawer Covers
To remove and replace covers:
1. Remove the crisper and meat drawer. Press up in center of crisper glass insert until it rises above the plastic frame.
Holding the crisper glass firmly, carefully slide the glass insert forward to remove.
2. Lift crisper cover frame and remove. Repeat steps to remove the meat drawer cover.
3. Replace back of meat drawer cover frame into supports or slides on side walls of the refrigerator and lower or slide the
front of the cover frame into place.
4. Slide rear of glass insert into cover frame and lower front into place. Repeat steps to replace the crisper cover.
16
The convertible vegetable/meat drawer can be adjusted to
properly chill meats or vegetables. The air inside the pan is cooled to prevent "spot" freezing and can be set to keep meats at the National Livestock and Meat Board recommended storage
temperatures of 28°- 32°F (-2 °- 0°C).
IMPORTANT: To extend freshness, wrap meats in airtight, moisture-proof materials before storing. Always store meat as
recommended.
Adjusting the control
The convertible control comes preset at the lowest meat setting. To change a control setting: Move the control to the right
(colder) or to the left (less cold) as desired.
To store vegetables: Set the control to VEG (all the way to the
left) to store vegetables at their optimal storage temperatures (which need to be warmer than those for meat).
O,
You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and
HIGH.
LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.
• Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.
• Vegetables with skins: Place in plastic bag or plastic container and store in crisper.
HIGH (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.
• Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.
IMPORTANT: If food starts to freeze, move the control to the left (less cold). Remember to wait 24 hours between adjustments. Doing so gives the temperature of the food time to change.
Meat storage guide
Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given,
freeze the meat.
Fresh fish or shellfish ........................ use same day as purchased
Chicken, ground beef, variety meat (liver, etc.) ................ 1-2 days
Cold cuts, steaks/roasts .................................................. 3-5 days
Cured meats .................................................................. 7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.
To remove and replace the wine rack (left) or can/bottle rack (right):
1. Remove the rack by pulling it straight out from the shelf.
2. Replace the rack by sliding it in between the shelf and the wall of the refrigerator.
NOTE: For long-term storage, place eggs in a covered container or in their original carton on an interior shelf.
17
Loading...
+ 39 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use