Whirlpool QCAM2730YQ0, CAM2762RQ0, CAM2762TQ0, CAM2762TQ2, CAM2762TQ3 Installation Guide

IMPORTANT:
Part No, 8524739
Read and save
these instructions
IM PORTANT: Installer: Leave Installation Instructions
with the owner.
Owner: Keep Installation Instructions for
future reference.
electrical inspector's use.
www.whirlpool.com
COMMERCIAL
WASHER
120-volt, 60-Hz Models
COMMERCIAL LAUNDRY
PRODUCTS
Before you start...
Your safety and the safety of others are very important.
We have provided many important
safety message in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alertsyou to
potentialhazards that can killor
hurtyou and others.
All safety messages will be preceded
by the safety alert symbol and the
word =DANGER" or WVARNING".
These words mean:
Check location where washer will be
installed, Proper installation isyour responsibilily, Make sure you have
everything necessary for correct
installation,
Do Not store or operate washer below 320F (0oC) (some water may remain in washer).
You can be killed or seriously
injured if you don't immediately
follow instructions.
You can be killed or seriously
injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
Single washer
installations require 12-inch (30 cm)
minimum risers to provide an air
cushion and
prevent noise and
damage to valves,
Grounded electrical outlet
is required, See Electrical
requirements,
Hot and cold water faucets: Must be
within 4 feet (1,2 meters) of the back of the washer and provide water
pressure 10 - 100 PSI (69-690 kPa), A pressure reduction valve should be used in the supply line where inlet
pressure entering the building exceeds 100 PSI(690 kPa) to prevent damage to the washer mixing valve,
Untape and
open washer
lid, Remove
packages and hoses from
washer,
screws
Front access to the pump area is available by removing 2 No, T20 Torx screws and then removing the front panel,
Important: Observe all governing codes and ordinances.
PAGE 2
Level floor: Maximum slope under washer- 1 inch (2,5 cm),
A floor drain should be
provided under the bulkhead, Prefabricated bulkheads with
electrical outlets, water supply lines and drain facilities should
be used only where local codes permit,
Water heater: Set to deliver 120°F (49°C)
water to the washer,
Standpipe drain system: Needs a two-
inch (5 cm) minimum carry-away
capacily of 17 gallons (64,4 liters) per
minute, Top of standpipe must be at least 39 inches (99 cm) high and no
higher than 72 inches (183 cm) from
bottom of washer,
Support: Floor must be sturdy enough to support loaded washer weight of 315 pounds (143 Kg),
® Registered trademark of TEXTRON
Recessed area instructions
l_is washer may be installed in a recessed area or closet.
The installation dimensions shown are the minimum spaces allowable,
Additional spacing should be considered for ease of installation
and servicing, If closet door is
installed, the minimum air openings in top and bottom of door are required,
Louvered doors with air openings in top and bottom are acceptable, Companion appliance spacing
should be considered,
l_inim_ml installation spacing
clo_l door
/ V
(/.6 cm)
48 sq. in.
(310 SCl.cm)
24_:1.in. V
(155 scI. cm)
VNN N
O
Dooccccocc_,x._4
3-
(7.6 cm)
i
Tools needed for installation:
level
flat-blade screwdriver
wrench
knife scissors
Parts supplied for installation:
Electrical requirements
Electrical Shock Hazard
Plug into a grounded 3-prong outlet. Do not remove ground prong. Do not use an adapter.
DO not use an extension cord. Failure to follow these instructions
can result in death, fire, or electrical shock.
Ifcodes permitand a separategroundwire isused,itisrecommended that a quaified eleclficiandeterminethat thegroundpath isadequate.
DoNatgreund toa gas pipe. Check witha qualifiedelecldcianifyouare
notsurethe washerisproperlygrounded. DoNot hovea fuseinthe neuketorground
circuit.
A 120-volt, 60-Hz,AC-only, 15-or
20-ampere fused electrical supply is required, (Time-delay fuse or circuit breaker isrecommended,) Itis recommended that a separate circuit serving only this appliance be provided,
48 sq. in.
(310 sq.cm)
(I 55 sq. cm)
17"
(43cm)
-,-rl-
¢loset door
4 e
(I 0 cm)
min.
Remove parts from packages, Check
that all parts were included,
I hose clamp
2 inlet hoses 4 flat water hose washers
2 front-leveling legs with nuts
I drain hose
Grounding instructions
_nisappliance must be grounded, Inthe event of a malfunction or breakdown,
grounding will reduce the riskof electric shock by providing a path of least
resistance for the electric current, Ynis
appliance is equipped with a cord having an eduipment-greunding conductor and a grounding plug, 1he plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances,
WARNING - Improper connection at the equipment-greunding conductor con
resuifino riskof eleclnc shock. Check with o quoifieq electrician or serviceman ifyou
ore in doubt as to whether the appliance is properly grounded, Do not modify the plug provided with the appiance - if it will not fit the ouifet, hove a proper outlet installed by a quaifieq electrician.
PAGE 3
6cm,
groun_:P3-pronplugpower_ J_Pe°nugtlg_°u_ground
supply cord
Now start...
Excessive Weight Hazard
Use two or more people to move
and install washer.
Failure to do so can result in back
or other injury.
Usa now hoses and washers that came
with your Whirlpool washer.
Replace inlet hoses after 5 years of use
to reduce the risk of hose failure,
Inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are
found, When replacing your inlet hoses,
mark the date of replacement on the label with a permanent marker,
coupling washer
mInsert a flat washer into each end
of the inlet hoses, Check that washers are firmly seated in couplings,
\
mPlace ho_e clamp over washer drain connector, Push drain hose onto washer connector, Use pliers to open
clamp and slide clamp over drain hose, Check for good fit,
shipping
lm Remove tape that covers
shipping strap, Pull to
completely remove the shipping strap with 2 coifferpins from the inside
of the washer,
Inletsare plastic.
Do Not stripor
cressthread.
cold Chock that hoso is not water twisted or kinked and is
inlet socuroly in placo. vaive
hotwater inletvalve
| •Altach hose to boltom inlet aiffaching water
valve opening first, Then second hose inlet hoses, run
;3' 7=g ore
to top inlet, Tighten couplings by water through =
additional two-thirds turn, a bucket, This will
hand; then use pliers to make an both faucets into _'iit
dill
_D Measure and mark a point
approximately 16 inches (40,6 cm) from the plug end of the shipping strap, Cut this shipping strap at this point,
Put "hook" end of drain
hose into standpipe, Tightly wrap the shipping strap around the standpipe, Push plug into
the nearest hole in the shipping strap,
get rid of particles
in water lines that
Mark which isthe hot water faucet,
Pull firmly to remove the end of shipping strap from the back of the washer, The shipping strap plug must
be completely removed from the washer for the self-leveling legs to
be released,
Save tho shipping strop for uso in Step 6.
PAGE 4
_;•Altach boiffom hose (inlet
might clog hoses,
Affach top hose (inlet marked "C') to
marked "H') to hot water faucet,
cold water faucet, Tighten coupling
Move washer close to final make final two-thirds turn,
position, Put "hook" end of drain hose into standpipe, Estimate length of
drain hose needed when washer is in final position, Hose must be cut exactly to length so "hook" end is
held tightly over edge of standpipe, If
drain hose istoo long, cut straight end of hose, (Do Not cut "hook" shaped
and of drain hose.)
DO NOTFORCEEXCESSLENGTHOF DRAINHOSEDOWN THESTANDPIPE.
THISCOULDCAUSESIPHONING.See
Step 6.
to faucet by hand; then use pliers to
dllk
UP •Stack two corner posts on top of
each other, Tiltwasher backwards and
insert corner posts 3 inches (7,6 cm) in
from one side of washer as shown,
Repeat with other corner posts on other
side of washer,
F
bose
112"
(1.3 cm)
NOTE: If the coin slide mechanism has
already been installed, skip this step and proceed to Step 16,
0 Plug power supply cord into
grounded outlet,
L nut
JM
1 U Use legs and nuts from parts
package, Screw nut down to within
1/2 inch (1,3 cm) of
base,
11.
Insert legs into correct holes at each front corner
of washer until nuts touch washer, Da Not tighten nuts until Step 14,
2 mTiltwasher backward and
remove corner posts, Gently lower washer to floor,
Move washer to its permanent location. Remove cardboard or
hardboard from under washer.
5 Remove the service door of
the meter case, Lift the service door
up at the back and remove, Install money accepting device (refer to manufacturers instructions for proper installation), For machines using coin
/
slides, use adapter kit (provided with
unit), Replace meter case service
door,
l_)m CHECKELECTRICAL
REQUIREMENTS.BESUREYOU HAVE
CORRECTELECTRICALSUPPLYAND
RECOMMENDEDGROUNDING METHOD.
1. Electromechanical Models
Only. Check the wash cycle time, The
washer has a 9-minute wash in the
Normal Cycle, Remove the timer from
the meter case of the washer to
manually staff the timer, Staff the
washer and allow it to complete the
Normal cycle,
Rotate counterclockwise
Timer-frontview
Timers can be started by turning the clutch assembly counterclockwise
until the washer starts to fill with water,
timer "off" position
3 mTiltwasher forward raising
back legs 1 inch (2,5 cm) off of floor, To adjust rear self-leveling legs, gently
lower washer to floor, Check levelness of the washer by placing a
carpenter's level on top of the washer, first side to side; then front to
back,
4mlf washer isnot level, adjust
the front legs up or down, Make final check with level,
When washer is level, use wrench to turn nuts on front legs up tightly against washer base. If nuts are not
fight against washer base, the washer may vibrate.
17.
Check that all parts are now installed, See parts list, Page 3, If there isan extra part, go back through steps to see which step was skipped,
1 _% mTurn on water faucets and
check for leaks, Tighten couplings if there is leaking, Do Not overtighten; this could cause damage to faucets,
_k
m _! •Check that you have all of your tools, Check that the shipping strap was removed from the back of
the washer and used to secure the drain hose,
If entire strop is not removed, washer may vibrate and be noisy.
2 If the washer fails to staff or
does not give the proper washer cycle time, the clutch assembly of the timer can be adjusted, Remove the timer from the meter case, Adjust the clutch assembly screw clockwise if
the washer does not staff after the coin slide mechanism has been fully
actuated in or out, Adjust the clutch assembly counterclockwise if the washer segment of the Normal cycle
was less than 9 minutes,
timer clutch adjuslment screw
PAGE 5
Loading...
+ 11 hidden pages