Whirlpool BLZS 5900/01 IN INSTALLATION

INSTALLATION OF THE OVEN COLUMN

Recommendations

IMPORTANT: Disconnect the oven from the
mains before carrying out any installation
work or servicing.

• Installation must be carried out by a qualified
technician in accordance with the manufacturer's
instructions and in compliance with local
regulations.

• Unpack the oven and make sure that the
appliance has not been damaged during transport
and that the oven door closes properly.

are not sure contact the dealer or the
nearest service centre.

• After removing the oven from its packaging,
leave it on the packing base to prevent it from
being damaged.

• When installing the oven it is advisable to wear
protective gloves.

• Do not lift the oven by the door handle, but grip
it at the sides.

If you

Preparing the housing unit

• Kitchen units in contact with the oven must be
heat resistant (80 °C min).

• Cut the kitchen unit before installing the
appliance. Carefully remove any shavings or
sawdust that could prevent the appliance from
operating properly.

• The dimensions of the oven and housing unit for
installation
in fig. 1-2-3.

• The dimensions of the housing unit for
installation of an

another oven of our manufacture

in fig. 4.

• To allow for proper ventilation, an opening
should be left at the bottom of the housing unit
(be sure to comply with the dimensions in the
drawing).

Once installation is completed, the bottom
of the oven must not be accessible.

• During installation, make sure that the sides of
the oven do not touch any adjacent units (fig. 5-

6).

of a single oven column

oven column combining

are shown

, are shown

Electrical connection

Regulations require that the appliance be
earthed.

• Connection to the mains must be carried out by
a qualified technician in accordance with the
manufacturer's instructions and in compliance
with local regulations.

• The installer is responsible for connecting
appliances correctly to the mains and for
observing the safety regulations.

• If the appliance is to be permanently connected
to the electricity mains supply, safety directives
require that an all-pole disconnect switch with a
minimum contact gap of 3mm be used for the
installation.

• Do not use multiple plug adapters or extension
leads.

• After the oven has been installed, the electrical
components must be inaccessible.

Connecting the oven to the power
supply

• Make sure that the voltage indicated on the rating
plate is the same as the mains voltage. The rating
plate is on the front edge of the oven (visible
when the door is open).

• If the power supply cable needs replacing, make
sure that it is replaced with a cable similar to the
one provided by the Manufacturer and that
installation is performed by the After Sales
Service or a Qualified Technician.

Securing the oven

• Insert the oven into the housing unit, being
careful not to trap the power supply cable.

• Center the oven in the housing unit before
securing it.

• Then anchor the oven to the housing unit using
the screws provided (fig. 7).

2

Fig. 5

Fig. 6

INSTALLATION INSTRUCTIONS

●

INSTALLATIONSANLEITUNG

●

INSTRUCTIONS POUR L'INSTALLATION

●

AANWIJZINGEN VOOR DE INSTALLATIE

●

ISTRUZIONI PER L’INSTALLAZIONE

●

INSTRUCCIONES PARA LA INSTALACIÓN

●

INSTRUÇÕES DE INSTALAÇÃO

●

Ο∆ΗΓΙΕΣ ΕΓΚΑΤΑΣΤΑΣΗΣ

●

INSTALLATIONSANVISNINGAR

●

ASENNUSOHJEET

●

INSTALLATIONSVEJLEDNING

●

ИНСТРУКЦИИ ПО УСТАНОВКЕ

●

MONTERINGSANVISNING

●

POKYNY NA INŠTALÁCIU

●

ИНСТРУКЦИИ ЗА ИНСТАЛИРАНЕ

●

NÁVOD K INSTALACI

●

INSTRUKCJE INSTALOWANIA

●

ÜZEMBE HELYEZÉSI ÚTMUTATÓ

●

INSTRUCŢIUNI DE INSTALARE

Fig. 7

5019 102 00123

DE GB FR

SE NO DK

NL

Ecological Paper

20/01/2006

FI