Whirlpool AWZ 414, AWG 400 PROGRAM CHART

Whirlpool is a registered trademark of Whirlpool USA

30120152GB.fm Page 1 Thursday, March 20, 2008 9:19 AM

AWG 400 PROGRAMME CHART

This washing machine is equipped with automatic safety functions which detect faults at an early stage and react appropriately, e.g.:

A. “Service” indicator B. “Clean Pump” indicator C. “Water Tap Closed” indicator D. “Door lock” indicator

E GF

}

E. Programme selector F. “Start” button G. “No spin” button

H. The programme sequence indicator

O. “Prewash” button

Programme

White Cotton

Antibacterial

Cotton

Synthetics

Delicates

Wool

Delicates

Wool / Silk

Handwash

Quick wash

Cold wash

Tempe-

rature

90 °C

60 °C

30 - 40 °C

30 - 60 °C

40 °C

Care

Labels

——

30 °C

35 °C

——

Max. Load

- For temperature selection, respect the manufacturer’s recommendations

on the care label

Normally to heavily soiled bed linen, table linen and underwear, towels,

5.0 shirts etc. made of cotton and linen.

At a temperature of 80°C or more, this programme eliminates bacteria,

5.0

ensuring sanitization of your laundry . The bacteria removal efficiency has been tested following a similar methodology to the NF EN 13697 standard of Nov. 2001.

5.0

Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen,

2.5

Trevira), polyamide (Perlon, Nylon) or blends with cotton.

2.5 Curtains and delicate clothing, skirts, shirts and blouses. Only woollens labelled with the Woolmark and identified as machine

washable.

1.0

This programme (40°C) is tested and approved by The Woolmark Company for handwashable wool.

1.0

Curtains and delicate clothing in wool or silk only washable in cold water.

Garments made of linen, silk, wool and viscose marked as

2.0

“handwashable”. Outer clothing worn for short periods and made of cotton, polyester,

2.5

polyamide and cotton blends.

Slightly soiled garments in cotton and/or synthetics washable only in cold

5.0

water.

Type of wash/Notes

Detergents and additives Special functions

Pre

wash

—

Main wash

Yes

Softener Pre

wash

LL L

—

——

—

No spin

Max.

spin

speed

rpm

Max.

800

500

800

500

800

Max.

Rinse Drain

Spin

: optional / Yes : dosing required

For improved garment care, spin speed is restricted in these programmes.

Black process 45.0° 150.0 LPI

——

5.0

Same as the last rinse and the final spin in the “Cotton” programme. In this programme spinning is intensive. Same as the spin cycle in the

“Cotton” programme.

The “wool” programme of this washing machine has been approved by The Woolmark Company for the washing of

garments labelled as “machine washable”. Follow the instructions given on the label sewn on the garment and the

instructions supplied by the washing-machine manufacturer. (Cert. no. M0402-M0403-M0404-M0405).

——

————

—

Max.

5019 301 20152

Whirlpool is a registered trademark of Whirlpool USA

30120152GB.fm Page 2 Thursday, March 20, 2008 9:19 AM

CONSUMPTION DATA

Programme

Temperature

(°C)

White Cotton / Antibacterial 90 5.0 52

Cotton with “Eco”

***

60 5.0 49 0.95 2:15

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. programme duration

(hours : minutes)

1.70 2:10

Cotton 40 5.0 62 0.51 2:00

Synthetics 60 2.5 46

0.80 1:40

Synthetics 40 2.5 46 0.46 1:35

Quick wash 35 2.5 30 0.40 0:40

Wool 40 1.0 56 0.44 0:54

Handwash 30 2.0 65 0.24 0:57

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. In domestic use, consumption data may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The time indicated on the display (if present) can deviate from the values in the table, because it takes into account the household

conditions applicable at that time. To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

Reference programme for energy label.

***

ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME

Add detergent as indicated on the front page and as described in the chapter “Detergent and Additives” in the Instructions for Use.

1. Turn the

programme selector

to the desired

programme.

SELECT ANY DESIRED OPTION

Press the buttons of any required options - the respective indicator lights up.

When the combination of programme and additional option(s) is not possible,

the indicators switch off automatically. Unsuitable combinations of options are deselected automatically.

“Prewash” button

• Only for heavily soiled loads (e.g. sand, granular dirt). Increases the cycle time by approx. 15 minutes.

• Do not use liquid detergent for the main wash

“No spin” button

• Excludes spinning from programme, press button. Suitable for delicate laundry.

with the “Cotton” and “Synthetics”

Note:

programmes a short spin cycle is provided in any case, even if the exclusion has been selected, in order to optimize rinsing results.

PROGRAMME START

Open the tap and press the indicator next to the

“Start”

. The

button lights up. The programme sequence indicator shows the current programme stage, running from left to right through Prewash, Wash, Rinse, Spin/Drain, End.

“DOOR OPEN” INDICATOR

At the end of a programme, the

“End”

indicator lights up signalling that the door can be opened. As long as a wash programme is running, the door remains locked and must not be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”.

when activating the prewash option.

RED INDICATORS

“Service” indicator

Lighting up of the “Service” indicator can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in the Instructions for Use; If the fault persists, contact our After-Sales Service.

“Clean pump” indicator

The water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned; in the latter case refer to the Instructions for Use (“Removing the filter”).

“Water tap closed” indicator

Machine water supply insufficient or lacking. Open the water tap; Turn the programme selector to “Off/0” and reset the programme. If the indicator remains on, refer to the “Troubleshooting Guide” in the Instructions for Use.

“Door lock” indicator

Lighting up of the indicator could be caused by the door not being properly closed. Try closing it again. Turn the programme selector to “Off/0” and reset the programme. If the indicator remains on, refer to the “Troubleshooting Guide” in the Instructions for Use.

PROGRAMME END

• Lighting up of the lamp on the wash sequence indicator means that the programme has ended and the door is unlocked.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

CHANGING PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START

1. Turn the programme selector to “Off/O”.

2. Select the new programme, any options and another spin speed if you want.

3. Press the

“Start”

button again. The new programme resumes the wash programme from where the previous one was interrupted. Do not add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END

• Reset by turning the programme selector to “Off/0” and select the “Drain Spin ” programme to remove the water remaining in the bowl before the door can be opened.

Black process 45.0° 150.0 LPI

5019 301 20152