Whirlpool AWOE 9420, AWOE 10420IS, AWO/D 7451, AWOD 8251, AWOD 7455 Instructions Manual

...

Dosing Aid

This function will suggest to you the correct amount of detergent for your wash load. By using the Dosing Aid you avoid detergent overdosing and • save detergent

• protect the environment

• protect sensitive skin

Before the first use... 1. Compare the dosing recommendation of the detergents you use with the dosing values preset in the washing machine. Adjust them if there is a mismatch.

Make sure that the Dosing Aid function can work optimally.

2. Check and eventually adjust the water hardness preset in the washing machine.

1. Detergent dosing values

The concentration of detergents available on the market differs considerably. This is why you have to adjust your washing machine settings according to your detergents.

Your washing machine comes with 3 preset dosing values for 3 different types of detergents (generic – delicates – dark colours). Each detergent type is associated to a group of programmes (see table on the right). Each of the 3 preset values should be adjusted as to match the dosing recommendation reported on the package of the detergent/s that you intend to use for each specific group.

Check and adjust one of the preset dosing values (Detergent calibration)

Suppose you want to check and adjust the preset dosing value for all the programmes belonging to the “Generic detergent group”.

Important: during this phase do not consider the local water hardness and the habitual soil level of your laundry. Simply follow the instruction below.

Dark colours Delicates Generic

Wool/Handwash

Dark

and

Delicates

All other programmes

A - Check

First Check on the package of your generic detergent which dosing amount is recommended for medium water hardness (or medium/soft) and medium soil level (or medium/light). Please use this value when you reach step 3 of the procedure described in the following section (see B - Adjust).

5019 106 01490

B - Adjust (Detergent Calibration)

Select a programme belonging to the programme group for which you want to check and possibly adjust the preset dosing value (for example the “Cotton” programme for the “Generic” group).

Press and hold the “Dosing Aid” button

for a few seconds.

Do this for all 3 programme groups.

It is sufficient to save a dosing value for ONE programme per group - it will be automatically saved for the other programmes of this group. For example, if you save a dosing value for “Cotton” it will be automatically saved for all programmes belonging to the “Generic” group.

If you want to change the saved dosing values (because you changed the type of detergent you use, for example) proceed as described above; the previously saved dosing value will be replaced by the new one for the programme group you selected.

The bottle symbol on the display lights up, and the preset detergent dosing value appears on the display.

Compare the preset value indicated on the display with the dosing amount previously identified (i.e., that recommended on your detergent package for medium water hardness and medium soil level). If they differ, adapt the displayed value now by pressing “+” or “-”

Press the “Ok” button to confirm and save

the new detergent value for the group.

The value on the display disappears, and

the display goes back to the initial state.

How to reset the dosing values you saved and go back to the preset values

For a specific programme group:

Select any programme belonging to the

group you want to reset the dosing value for.

Press and hold the “Dosing Aid” button for a few seconds - the bottle symbol and the currently saved dosing value are displayed.

Press the “Reset/Drain” button briefly “rES” appears on the display for a short period.

The preset dosing value appears on the display. Press the “Ok” button to confirm.

For all programmes:

Select programme “Rinse & Spin”. Press and hold the “Dosing Aid” button

for a few seconds - the bottle symbol and three horizontal bars appear on the display.

Press the “Reset/Drain” button briefly -

“rES” appears on the display.

Press the “Ok” button to confirm and reset all preset values.

5019 106 01490

+ 2 hidden pages