Page 1
30110239GB.fm Page 19 Monday, July 18, 2005 6:16 PM
CONTENTS
BEFORE USING THE WASHING MACHINE
FIRST WASH CYCLE
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
DESCRIPTION OF THE WASHING MACHINE
CHILD SAFETY (IF AVAILABLE)
PREPARATION OF THE WASHING
DETERGENTS AND ADDITIVES
WASHING PROGRAMME
REMOVING THE FILTER
DRAINING RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
ACCESSORIES
TRANSPORT AND HANDLING
INSTALLATION
ELECTRICAL CONNECTION
Black process 45.0° 100.0 LPI
19
Page 2
30110239GB.fm Page 20 Monday, July 18, 2005 6:16 PM
BEFORE USING THE WASHING MACHINE
1.Removing the packaging and check
•
After unpacking, make sure that the washing
machine is undamaged. If in doubt, do not use the
washing machine. Contact After-Sales Service or
your local retailer.
•
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children,
as they are potentially dangerous.
2.Remove the transit bolts
•
The appliance is fitted with transit bolts to
prevent internal damage during transport.
Before using the washing machine you must
remove the transit bolts
Remove the transit bolts”).
(see “Installation/
3.Install the washing machine
•
Remove the protective foil from the control
panel (if available).
•
Move the machine without carrying it at the top.
•
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
•
Adjust the feet to ensure that the machine is
stable and level (see “Installation/Adjust the
feet”).
4.Water supply
•
Connect the water supply inlet hose in
accordance with regulations of your local water
company (see “Installation/Connect the water
inlet hose”).
•
Water supply: cold water only
•
Tap: 3/4” threaded hose connection
•
Pressure: 100-1000 kPa (1-10 bar).
5.Drain hose
•
Connect the drain hose to the siphon or hook it
over the edge of a sink by means of the “U” bend
(see “Installation/Connect the water drain hose”).
•
If the washing machine is connected to a built-in
drainage system, ensure the latter is equipped
with a vent to avoid simultaneous loading and
draining of water (siphoning effect).
6.Electrical connections
•
Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and current standard
safety regulations.
•
Voltage information, power consumption and
electrical protection data are supplied on the
inside of the appliance door.
•
The appliance must be connected to the mains
exclusively by means of a socket with an earth
connection in accordance with established
regulations. The appliance must be earthed by
law. The manufacturer declines all liability for
damage to property or injury to persons or
animals deriving either directly or indirectly from
failure to observe the directions.
•
Do not use extension leads or multi sockets.
•
Before any maintenance on the washing machine
disconnect it from the mains supply.
•
Access to the mains plug or to disconnection
from mains supply via a double-pole switch must
be ensured at all times following the installation.
•
Do not operate the washing machine if it has
been damaged during transport. Inform the
After-Sales Service.
•
Mains cable replacement is only to be carried out
by After-Sales Service.
•
The washing machine must only be used in the
household for the prescribed uses.
Minimum housing dimensions:
Width: 600 mm
Height: 825 mm
Depth: 600 mm
20
Black process 45.0° 100.0 LPI
Page 3
30110239GB.fm Page 21 Monday, July 18, 2005 6:16 PM
FIRST WASH CYCLE
We recommend the first wash cycle be made without laundry.
This will remove any residual water used in testing your washing machine.
1.
Turn on the tap.
2.
Close the appliance door.
3.
Pour a small amount of detergent (about 30 ml) into the detergent dispenser .
4.
Select a short program (see programme chart).
5.
Press the
“On/Off”
button.
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
1.Packing
•
The packing box may be fully recycled as confirmed
by the recycling symbol. Adhere to local
regulations when disposing of packaging material.
2.Energy saving tips
•
Achieve the best use of energy, water, detergent
and time by using the recommended maximum
load size.
•
Do not exceed the detergent dosages indicated
in the manufacturer’s instructions.
•
The Eco Flap - a special system in the outlet - will
prevent detergent loss from the drum to avoid
detergent loss into the environment.
•
Use “Prewash” for heavily soiled laundry only!
Save detergent, time, water and energy
consumption by not selecting “Prewash” for
slight to normally soiled laundry.
•
Pretreat stains with stain remover or soak dried
in stains in water before washing to reduce the
necessity of a hot wash program.
•
Save energy by using a 60° C instead of a 90° C
wash programme or a 40° C instead of a 60° C
wash programme.
•
Save energy and time by selecting a high spin
speed to reduce the water content in laundry
before using a tumble dryer (for machines with
adjustable spin speed).
3.Disposing of packaging and old appliances
•
This appliance is marked according to the
European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product, or on the
documents accompanying the product, indicates
that this appliance may not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling
of electrical and electronic equipment.
Disposal must be carried out in accordance with
local environmental regulations for waste disposal.
For more detailed information about treatment,
recovery and recycling of this product, please
contact your local city office, your household
waste disposal service or the shop where you
purchased the product.
•
The washing machine is built from reusable
materials. The washing machine must be disposed of
in compliance with local waste disposal regulations.
•
Before scrapping, cut off the power cable so that the
washing machine cannot be connected to the mains.
•
Remove detergent from compartment if you
intend scrapping your appliance.
4.Child safety
•
Children must not be allowed to play with the
washing machine.
5.General recommendations
•
When the appliance is not in use unplug it and
turn off the tap.
•
Before cleaning or carrying out maintenance,
switch off the washing machine and disconnect it
from the mains supply.
•
To clean the outside of the washing machine, use
a neutral detergent and a damp cloth.
•
Do not use abrasive detergents.
•
Do not attempt to force the door open.
•
If necessary, the power cable may be replaced
with an identical one obtained from our AfterSales Service. The power cable must only be
replaced by a qualified technician.
6.EC Declaration of Conformity
•
This washing machine has been designed,
constructed and distributed in compliance with
the safety requirements of EC Directives:
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
93/68/EEC CE Marking Directive
Black process 45.0° 100.0 LPI
21
Page 4
30110239GB.fm Page 22 Monday, July 18, 2005 6:16 PM
DESCRIPTION OF THE WASHING MACHINE
1.
Worktop
2.
Control panel
3.
Detergent dispenser
4.
After-Sales Service sticker
(on the back side of the door)
5.
Door
6.
Door handle
•
To open the door press the
button on the inside of the
handle and pull
•
Close the door by pushing it
firmly (the lock will click into
place)
7.
Child safety (inside door if
available)
8.
Filter (behind cover)
9.
Plinth
10.
Adjustable feet
3
9
1
2
4
5
6
7
8
10
CHILD SAFETY (IF AVAILABLE)
To protect the appliance from improper use, turn the plastic
screw on the interior of the door using a coin or the thick
rounded plastic projection on the coloured insert from the
detergent dispenser:
•
Slot vertical: safety position, i.e. the door will not lock.
•
Slot horizontal: normal position, i.e. the door can be locked
again.
22
Black process 45.0° 100.0 LPI
Page 5
30110239GB.fm Page 23 Monday, July 18, 2005 6:16 PM
PREPARATION OF THE WASHING
1.Sort the laundry according to...
• Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics,
wool, handwashed items
• Colour
Separate coloured and white items. Wash new
coloured articles separately
•Size
Laundry items of different sizes distribute
themselves better in the drum and optimise the
washing and spinning action
• Delicates
Wash small items (e.g. nylon stockings, belts etc.)
and items with hooks (e.g. bras) in a washbag or
pillow case with a zip fastener. Always remove
curtain glides or wash curtains with the glides
inside a cotton bag
2.Empty all pockets
Coins, safety pins etc. can damage the laundry,
drum and tub.
3.Closures
Close zips and hooks and eyes; Tie loose belts or
straps together.
Stain removal
•
Blood, milk, eggs etc. are generally removed by
the automatic enzyme phase of the programme
•
To remove red wine, coffee, tea, grass and fruit
stains etc. add a stain remover to the detergent
dispenser chamber
•
Pre-treat heavily-soiled areas with stain remover
if necessary
Dyeing
•
Only use dyes that are suitable for washing
machines
•
Follow the manufacturer’s instructions.
•
Plastic and rubber parts of the washing machine
can be stained by dyes
Loading the laundry
1.
Open the door.
2.
Unfold the laundry and place it loosely in the
drum. Observe the load sizes given in the Quick
Reference Guide.
Note:
overloading the machine will result in
unsatisfactory washing results and creased laundry.
3.
Close the door.
DETERGENTS AND ADDITIVES
The choice of detergent depends on:
•
type of fabric (cottons, easy care/synthetics,
delicate items, wool).
Note:
Use only specific detergents for washing
wool
•
colour
•
the wash temperature
•
degree and type of soiling
Remarks:
Whitish residues on dark fabrics are caused by
insoluble compounds used in modern phosphatefree powder detergents. If this occurs, shake or
brush out the fabric or use liquid detergents.
Use only detergents and additives specifically
produced for domestic washing machines.
When using descaling agents, dyes or bleaches for
the pre-wash, make sure that they are suitable for
use in domestic washing machines. Descaler could
contain components which can attack parts of your
washing machine
Do not use any solvents (e.g. turpentine, benzine).
Do not wash fabrics in the machine which have
been treated with solvents or flammable liquids.
Water hardness chart
Water hardness Characteristics
1
2
3
4
soft
medium
hard
very hard
Dosage
Follow the dosage recommendations on the
detergent pack. They depend on:
•
degree and type of soiling
•
size of wash
full load follow the detergent manufacturer’s
instructions;
half load: 3/4 the amount used for a full load;
Minimum load (about 1 kg):
1/2 the amount used for a full load
•
water hardness in your area (request information
from the water company). Soft water requires
less detergent than hard water (refer to water
hardness table)
Notes:
Too much detergent can result in excess foam
formation.
The cleaning effect deteriorates.
If the washing machine detects too much foam, it
may prevent spinning.
Insufficient detergent may result in grey laundry in
time and also calcifies the heating system, drum and
hoses.
German
°dH
0-7
7-14
14-21
over 21
French
12-25
25-37
over 37
°fH
0-12
English
°eH
0-9
9-17
17-26
over 26
Black process 45.0° 100.0 LPI
23
Page 6
30110239GB.fm Page 24 Monday, July 18, 2005 6:16 PM
Pouring in the detergents and additives
The dispenser has three (models
depending on model.
Chamber
•
Detergent for the prewash
Chamber
•
Detergent for the main wash
•
Stain remover
•
Water softener (water hardness 4)
When using liquid detergent, remove the coloured insert from the
detergent container and insert it in the first gap in
chamber . The scale on the insert makes dosing easier.
Chamber
•
Fabric Softener
•
Liquid starch
Only pour additives in up to the “Max” mark.
“A1”
or
“A2”
) chambers
A1
A2
B2
Notes:
•
Keep detergents and additives in a safe, dry place out of the reach of children.
•
Liquid detergents can be used for programmes with prewash. In this case only measure in a powder
detergent for the main wash.
•
To prevent dispensing problems when using highly concentrated powder and liquid detergents, use the
special detergent ball or bag supplied with the detergent and place it directly inside the drum.
•
When using descaling agents, bleaches or dyes, make sure that they are suitable for washing machines.
Descalers could contain components that can attack parts of your washing machine.
•
Do not use any solvents in the washing machine (e. g. turpentine, benzine).
•
If you use starch powder, proceed as follows:
1.
Wash your laundry using the desired wash programme.
2.
Then stir the starch in with water in a beaker.
3.
Select the “Rinse and Spin” programme, reduce the speed to 800 rpm and start the programme.
4.
Pull out the detergent drawer until you can see about 3 cm. of chamber .
5.
Pour the starch solution into chamber while the water is running into the detergent drawer.
6.
If there are starch residues in the detergent drawer when the programme has finished, clean it if
necessary (see “Cleaning and Maintenance”).
Take note also of the starch manufacturer’s information.
24
Black process 45.0° 100.0 LPI
Page 7
30110239GB.fm Page 25 Monday, July 18, 2005 6:16 PM
WASHING PROGRAMME
Selecting the programme:
1.
Plug in the appliance.
2.
Turn on the water supply tap.
3.
4.
5.
6.
7.
During the selected washing programme the programme selector knob moves by steps
clockwise through the phases
seconds to several minutes.
Options
Easy Ironing •
Energy save /
Eco
Quick wash /
Rapid
Intensive
rinse
Rinse hold /
Spin delay
Spin speed
reduction
No spin •
Half Load
Cold Wash •
Programme Selector
Set the
Depending on model, set the
Depending on model, set the
additional options
Select
further pressing
By a
Check that the door is well closed. Press the
For models fitted with “Start delay”, programme starts after some seconds: during these seconds you
can select delay time.
(depending on model)
Can be used together with Cotton and Synthetics programmes to make ironing easier.
•
Increases the water quantity and the clothes are spun very gently.
•
The duration of the wash is extended and the temperature reduced to save energy
maintaining good washing results.
•
Select for quick, economical washes.
•
Especially suitable for small, lightly soiled loads.
•
More water and a longer time in rinse cycle is added.
•
The intensive rinse function is especially suitable for areas with particularly soft
water, for baby clothes and to help people with allergies.
•
The laundry remains in the last rinse water without being spun, to avoid heavy
creasing and to prevent colours from changing.
•
Especially suitable for the “Synthetics” or “Delicates” programmes, if the laundry is
not to be unloaded immediately after the end of the programme.
•
This function is particularly useful if you want to postpone spinning to a later time or
when you do not wish to spin the clothes.
Continuing wash cycle after rinse hold:
•
Press the Rinse hold button again; the load will be spun according to the selected
programme.
If you do not wish to spin the clothes, turn the programme selector knob to the drain.
•
Press this button to reduce the predetermined automatic maximum spin speed. In
some programmes the maximum final spin speed is limited to go easy on your
laundry items. Selection of a higher spin speed is not possible.
Press this button to exclude the spin function from the programme.
Note:
If “No spin” is selected:
•
the “Wool” and “Delicates” programme do not run a spin cycle.
•
the “Cotton” and “Synthetics” programmes run a reduced spin speed cycle
between rinses to ensure effective rinsing.
•
if the spin speed “0” is selected, the final spinning is cancelled. The water is drained
out only.
• reduces water consumption, above all during rinsing.
• suitable for lightly-soiled laundry and small loads (max 3 kg).
Note:
Reduce the detergent quantity.
With this option water is heated only up to 20° C.
knob to the desired programme.
Temperature Selector
Spin Speed Selector
, if desired, pressing the corresponding button.
of the button this option can be turned off again.
prewash, main wash, rinse
knob to the desired temperature.
knob to the desired spin speed.
“On/Off”
button. The indicator light will come on.
and
spin
. Each step takes from some
Black process 45.0° 100.0 LPI
25
Page 8
30110239GB.fm Page 26 Monday, July 18, 2005 6:16 PM
Start delay
1.
Select the programme and temperature, any additional options and the spin speed.
2.
Press the
3.
During these 6 seconds press the “Start Delay” button and select delay time: 0,3,6,9 hours.
4.
The programme will start at the desired time, or after 6 seconds if “0” is selected.
• To change the start delay: press the “Start Delay” button to select time.
• To cancel the start delay: press the “Start Delay” button until “0” appears: the selected programme
will then start.
• If options are changed during the delay time period: the programme will start with newly selected
options.
• If the programme is changed during the delay time period: “Start Delay” will switch automatically to
“0”. Reselect the Start Delay time to activate.
N.B.
(depending on model)
“On/Off”
With liquid detergent, a dosing aid placed directly in the drum should be used if a start delay has
been selected.
button. The display flashes “0” for 6 seconds.
Door lock
The door locks automatically after the programme start until the end of the programme.
If the programme selector is moved to the “Stop” position or if the electricity supply is interrupted, then
after approximately one minute the door is released.
In this case do not open the door, because hot water could be released from the appliance.
Programme end
The programme selector knob is at the stop position.
1.
Press the
2.
Cancel the special options by pressing the appropriate buttons.
3.
Turn the water supply tap off.
4.
Wait for the door to unlock (about one minute).
5.
Open the door and unload the machine.
N.B.
“On/Off”
Do not fully close the door but leave it ajar to allow the drum to dry out.
button. The indicator light turns off.
Changing programme
1.
Press the
2.
Select the new programme.
3.
Press the
For this programme do not add any further detergent.
“On/Off”
“On/Off”
button. The indicator lights turns off.
button. The new program will re-start.
Changing options
The options can be selected or deselected without switching off the appliance.
Programme interruption or pause
To interrupt the running programme for a certain period and continue it at a later time:
1.
Press the
2.
Following the desired pause press the
“On/Off”
button.
“On/Off”
button once again.
Cancelling the programme
If the current programme is to be terminated prematurely and cancelled, the water must be pumped out
first before the door can be opened:
1.
Press the
2.
Set the programme selector to programme setting
3.
Press the
26
Black process 45.0° 100.0 LPI
“On/Off”
“On/Off”
button to switch off the appliance.
“Drain”
button in order to start the
“Drain”
.
programme.
Page 9
30110239GB.fm Page 27 Monday, July 18, 2005 6:16 PM
REMOVING THE FILTER
We recommend that you check and clean the filter regularly,
at least two or three times a year.
Especially:
•
When the appliance does not drain or spin properly
•
If the pump is blocked by a foreign body (e.g. buttons,
coins or safety pins)
IMPORTANT: make sure the water has had time to
cool before draining the appliance.
1.
Switch off the appliance and unplug it.
2.
Open the filter cover. Open the filter cover with the help
of the coloured insert from the detergent container.
3.
Place a container beneath it.
4.
Open the filter but do not withdraw it completely. Slowly
turn the handle anticlockwise until the water drains out.
5.
Wait until all the water has drained off.
6.
Now unscrew the filter completely and remove it.
7.
Clean the filter and the filter chamber.
8.
Check that the pump rotor moves freely.
9.
Insert the filter with the guide pin upwards and screw it
in clockwise to the stop (handle horizontal).
10.
Pour about 1 litre of water into the detergent drawer to
reactivate the Eco system. Check that the foreign body
trap is seated properly and tightly in place.
11.
Fold the cover up and lock it.
12.
Reinsert the plug in the socket.
13.
Select a programme and start it.
Black process 45.0° 100.0 LPI
27
Page 10
30110239GB.fm Page 28 Monday, July 18, 2005 6:16 PM
DRAINING RESIDUAL WATER
Before emptying the residual water, switch the appliance off and unplug it from the
mains socket.
Open the cover to the foreign body trap. Open the filter cover with the help of the
coloured insert from the detergent container. Place a container beneath it.
1.
Open the filter but do not withdraw it completely. Slowly turn the handle anticlockwise until the
water drains out.
2.
Wait until all the water has drained off.
3.
Now unscrew the filter completely and remove it.
4.
Tilt the appliance forwards carefully to allow the water to flow out.
5.
Insert the filter with the guide pin upwards and screw it in clockwise to the stop (handle horizontal).
6.
Fold the cover up and lock it.
Before using the washing machine again:
1.
Pour approx. 1 litre of water into the detergent drawer to reactivate the Eco system.
2.
Reinsert the plug in the socket.
CARE AND MAINTENANCE
Appliance exterior and control panel
•
Can be washed down with a soft, damp cloth
•
A little neutral cleaner (not abrasive) can be used
•
Dry with a soft cloth
Door seal
•
Clean with a damp cloth when necessary
•
Check the seal folds for foreign bodies
periodically
Filter
•
We recommend that you check and clean the
filter regularly, at least two or three times a year
see “Removing The Filter”)
28
Black process 45.0° 100.0 LPI
Page 11
A
A2
30110239GB.fm Page 29 Monday, July 18, 2005 6:16 PM
Detergent dispenser
1.
Press the release lever in the prewash compartment downward
and remove the drawer.
2.
Remove the inserts (the siphon from the softener compartment
and the coloured insert for liquit detergents).
3.
Wash all the parts under running water.
4.
Replace the parts and refit the detergent dispenser. Insert the
detergent dispenser in the washing machine.
A1
Water hose mesh filter.
Check and clean periodically.
For machines with a straight water supply hose
1.
Turn off the tap
2.
Unscrew the hose from the tap.
3.
Clean the internal filter.
4.
Screw the supply hose back onto the tap.
5.
Unscrew the hose from the machine
6.
Remove the filter from the washing machine with pliers and clean
it.
7.
Replace the filter and screw the hose connection back on the
machine.
8.
Turn on the tap and ensure that the connections are completely
water-tight.
For machines with Water Stop hose
1.
Turn off the tap
2.
Unscrew the Water Stop hose from the tap.
3.
Clean the internal filter.
4.
Screw the Water Stop hose back onto the tap.
5.
Turn on the tap and ensure that the connections are completely
water-tight.
“A”
“B”
(depending on the model)
A
B
Black process 45.0° 100.0 LPI
29
Page 12
30110239GB.fm Page 30 Monday, July 18, 2005 6:16 PM
TROUBLESHOOTING GUIDE
The appliance will not start, no lamp lights
up.
Check whether:
•
the appliance is plugged in;
•
the wall socket is functioning correctly
(use a table lamp or similar).
•“On/Off”
button pressed.
The appliance will not start, but the “On/
Off” lamp is on.
Check whether:
•
the appliance door is properly closed
(child safety);
•
a programme has been selected and the
programme is started;
•
the water tap is open. If not, open the tap and
switch the appliance first off, then on.
The appliance stops during the programme.
Check whether:
•
“Rinse Hold”
the
this option by pressing the button again;
•“On/Off”
button is pushed, terminate
lamp is off. Press
“On/Off”
button;
No water or insufficient water supply.
Check whether:
•
the tap is turned on completetly;
•
kinks are present in water hose;
•
the water hose filter is blocked;
•
the water hose is frozen up;
N.B: Afterwards switch the appliance off, then
on.
Waste water not pumped out.
Check whether:
•
the drain hose is correctly installed
(see “Installation Instructions”);
•
the filter is blocked.
•
the drain hose is frozen up.
•
the “Rinse hold” button is pressed.
Detergent and additive product residues
in dispenser at end of wash.
Check whether:
•
the siphon is correctly installed and clean
(see “Care and Maintenance”);
•
enough water is being supplied. The mesh filters
between the inlet hose and the tap could be
clogged (see “Care and Maintenance”). Check
and clean the filter two or three times a year (see
“Removing the filter”).
Also see “Detergent and Additives” for information.
30
The appliance vibrates during the spin
cycle.
Check whether:
•
the appliance is levelled and solidly installed on all
four feet (see “Installation Instructions”);
•
the transit bolts have been removed. The transit
bolts must be removed before the appliance can
be used (see “Installation Instructions”).
Water Stop fault (depending on model)
When the appliance detects a water leakage the
pump runs continuously.
Switch off the appliance, unplug it and make sure
that the water tap is closed.
The “Water Stop” may have been triggered by:
1.
too much foam;
2.
leakage in the inlet hose or in the appliance.
Tilt the appliance forwards carefully to allow the
collected water to flow out from the bottom of the
appliance. Then:
1.
connect the appliance to the electrical outlet,
2.
open the tap,
3.
reselect the desidered programme and press the
“On/Off”
Important:
Service with details about the fault (see “After-Sales
Service”).
button.
if the fault occurs again, call After-Sales
Final spin results are poor:
The appliance has an imbalance detection and
correction system. If individual heavy articles are
loaded (bathmat, bathrobe, etc.) this system may
reduce the spin speed automatically to protect the
appliance or even interrupt the spin cycle
altogether, if the imbalance is too great even after
several spin starts.
•
if the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to balance
the load and repeat the spin cycle.
•
excessive foam formation may prevent spinning.
Ensure correct amount of detergent is used
Important:
system. The programme is interrupted after a few
minutes if one of the following happens:
•
no water supply;
•
pump blocked.
If the pump is blocked, switch off the appliance and
clean the pump (see “Removing the filter”). Then
re-start the appliance.
this machine is fitted with a safety
Black process 45.0° 100.0 LPI
Page 13
30110239GB.fm Page 31 Monday, July 18, 2005 6:16 PM
AFTER-SALES SERVICE
Before contacting After-Sales Service:
1.
Try to remedy the problem yourself (see
“Troubleshooting Guide”).
2.
Restart the programme to check whether the
problem has solved itself.
3.
If the machine continues to function incorrectly,
call After-Sales Service.
ACCESSORIES
Via our After Sales Service or your specialist dealer,
you can obtain
•a Pedestal Drawer
beneath your washing machine. It raises your
machine to allow for more comfortable loading
and unloading, as you now no longer need to
bend as far to access the unit. Furthermore, it
offers a great space-management tool and
storage solution.
•a Stacking Kit
your dryer on top of your washing machine and
thus effectively save space.
which can be installed
by means of which you can fix
Specify:
•
The nature of the problem.
•
The exact model of the appliance.
•
The service code (number after the word
SERVICE).
The After-Sales Service sticker is on the inside
of the door.
•
Your full address.
•
Your telephone number and area code.
After-Sales Service phone numbers and
addresses are given on the guarantee card.
Alternatively, consult the dealer where you
purchased the appliance.
Some models are able to be installed under your
kitchen worktop; in that case, please contact our
After Sales Service (see above). Be aware that
•
the appliance MUST be installed under a
continuous worktop
•
according to the legal safety regulations, the
installation of the appliance MUST be carried out
by an authorized technician or by our After Sales
Service
•
the appliance MUST be installed using the
intermediate cover panel of the
which can be obtained from specialist dealers or
our After Sales Service
UBS Base Set
TRANSPORT AND HANDLING
Never move the appliance by carrying by the worktop.
1.
Unplug the appliance.
2.
Turn off the tap.
3.
Remove the water supply and drain hose.
4.
Eliminate all water from the hoses and from the appliance (see “Removing the Filter”,
“Draining Residual Water”).
5.
Fit the transit bolts (obligatory) (see “Installation Instructions”).
Black process 45.0° 100.0 LPI
31
Page 14
30110239GB.fm Page 32 Monday, July 18, 2005 6:16 PM
INSTALLATION
Remove the transit bolts
1.
Slacken the four bolts with the spanner supplied.
2.
Unscrew the bolts by hand.
3.
Holding the bolt head, pull each bolt through the wide
part of the holes.
4.
Close the holes with the plastic covers supplied; insert
the covers in the wide part of the hole and slide them
toward the narrow part until they click into place.
5.
Keep the transit bolts for future use.
•
Whenever the appliance is transported, the transit bolts
must be refitted:
1.
Pry off the plastic covers with a screwdriver, slide them
in the opposite direction of the arrow and remove.
2.
Insert the transit bolts, performing the steps for removal
in reverse order.
Adjust the feet
If the floor is uneven, adjust the levelling feet as required (do
not insert pieces of wood etc. under the feet):
1.
Slacken the locknut using the spanner supplied.
2.
Adjust the height of the foot, turning it by hand.
3.
Tighten the locknut by turning it anti-clockwise towards
the appliance casing.
If the appliance is to be installed on a wooden floor,
distribute the weight by placing it on a 60 x 60 cm sheet of
plywood at least 3 cm in thickness.
Secure the plywood sheet to the floor.
32
Black process 45.0° 100.0 LPI
Page 15
30110239GB.fm Page 33 Monday, July 18, 2005 6:16 PM
Worktop for built-under models
The appliance
If the appliance will be built under
from specialist shops or from After-Sales Service.
1.
Unplug the appliance.
2.
Unscrew the worktop fixing screws from the rear of the appliance.
3.
Slide the worktop fully backward and lift it upwards to remove. Install the cover panel following the
relative instructions.
4.
Refit the fixing screws and tighten them.
5.
Plug the appliance only into the mains power socket.
must
only be installed beneath a continuous fitted kitchen worktop.
Connect the water inlet hose
For models with straight hose “A”
1.
Insert the dirt strainer (already premounted on the hose
end or included in the accessories) into the threaded tap
coupling.
2.
Carefully screw the hose connection onto the tap
preferably by hand.
3.
Make sure there are no kinks in the hose.
4.
Check water-tightness of tap and appliance connections
by turning the tap completely on.
If the hose is too short, replace it with a suitable length of
pressure resistant hose (1000 kPa min, EN 50084 approved
type).
Periodically check the hose for brittleness and cracks and
replace if necessary.
The appliance can be connected without an antibackpressure valve.
it is mandatory
to use the cover panel UBS. This can be obtained
A
For models with Water Stop hose “B”
If the flexible hose is damaged, unplug the appliance from
the mains immediately.
1.
Screw the threaded connector with the filter inserted
onto the tap.
2.
Check water-tightness of tap and appliance connections
by turning the tap completely on.
If the hose is too short, replace it with a 3 m Water Stop
hose (available from After-Sales Service or from your
dealer). This operation must be carried out exclusively by a
licensed electrician.
The appliance
a non-pressurized water heater.
The inlet hose and the plastic enclosure at the tap
connection contain electrical components.
hose and do not immerse the plastic enclosure in
water.
Black process 45.0° 100.0 LPI
must not
be connected to the mixing tap of
Do not cut the
B
33
Page 16
30110239GB.fm Page 34 Monday, July 18, 2005 6:16 PM
Connect the water drain hose
The draining varies according to model:
External drain hose
1a.
Unhook the drain hose from the left clip.
Attention: do not unhook
the right drain hose connection.
Internal drain hose
1b.
Pull the hose completely out of the holder. The holder can be on the
right or on the left on the rear side (depending on the model).
Close off the hole with the attached cap.
2.
Connect the drain hose to the siphon or hook it over the edge of a sink
by means of the “U” bend supplied.
3.
Make sure there are no kinks in the hose.
4.
Secure the hose so that it cannot fall down while the appliance is running.
The drain hose should not be hooked onto small washbasins.
If you need to add an extension, use a flexible hose of the same type and
secure the union with screw-on hose clips.
Max. drain hose length: 2.50 m
Max. drain height: 1.25 m
Min. drain height: 0.70 m
1a
1b
34
Black process 45.0° 100.0 LPI
Page 17
30110239GB.fm Page 35 Monday, July 18, 2005 6:16 PM
ELECTRICAL CONNECTION
Do not use extension leads or multi sockets.
Electrical connections must be made in accordance with local regulations.
1) Warning - this appliance must be earthed
This appliance is normally supplied with a mains lead having a plug fitted in the factory which has been
checked for correct earth continuity.
If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not fitted with a
plug, you should fit a suitable new, good quality plug by following the instructions in (2) below.
Any unsuitable plug should be cut off and disposed of in order to avoid a possible shock hazard should it be
inserted into a socket.
2) CONNECTION TO A REWIRABLE PLUG - to be carried out only by a qualified electrician
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN AND YELLOW - “EARTH” (“E”)
To fit a new plug, proceed as follows:
2.1 Polarized Plugs (e.g. 3 pin, 13 amp plug conforming to
BS 1363A)
a.
The GREEN AND YELLOW wire must be connected to the
terminal in the plug which is marked with the letter “E” or by
the Earth symbol or coloured green and yellow.
b.
The BLUE wire must be connected to the terminal which is
marked with the letter “N” or coloured blue.
c.
The BROWN wire must be connected to the terminal which is
marked with the letter “L” or coloured brown.
2.2) Non-polarized plugs (e.g. 2 pin with side earth contact)
The wire which is coloured GREEN AND YELLOW must be connected to the earth contact. The other two
wires should be connected to the two pins, irrespective of colour.
Black process 45.0° 100.0 LPI
FUSE REPLACEMENT
If the mains lead of this appliance is fitted with a BS 1363A 13 amp
fused plug, replace the fuse only with an A.S.T.A. approved type
conforming to BS 1362 and proceed as follows:
Remove the fuse cover (A) and the fuse (B).
Fit the replacement 13 A fuse into the fuse cover.
Refit both into the plug.
For all other types of plug, the supply socket should be protected by
a 16 A fuse or circuit breaker at the distribution board.
35
Loading...