Whirlpool AKZ 307, AKZ 307 WH, AKZ 313 INSTRUCTION FOR USE

TABLE OF CONTENTS GB
INSTALLATION
ELECTRICAL CONNECTION
BEFORE USING THE APPLIANCES
PROTECTING THE ENVIRONMENT
ENERGY SAVING TIPS OVEN ACCESSORIES
COOKTOP ACCESSORIES
COOKING CHARTS
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
4
6
7
7
7
8 9
9
10
CLEANING THE OVEN AND ACCESSORIES
CARE AND MAINTENANCE OF CONVENTIONAL ELECTRIC COOKTOPS
CARE AND MAINTENANCE OF GLASS-CERAMIC COOKTOPS
TROUBLESHOOTING GUIDE
AFTER SALES SERVICE
DECLARATION OF CONFORMITY CE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
11
13
13
13
14
14
3
INSTALLATION
Technical information for the installer
OVEN
After removing the oven from its packaging, before
making the connections place it on the polystyrene foam base to protect it from damage.
Do not attempt to lift the oven by the handle.
Lift at the sides as shown in the figu re (see arrow). Check that the appliance has not been d amaged in
transit. Oven dimensions and kitchen unit dimensions are
shown in the opposite figure. Kitchen units in contact with the oven must be heat
resistant (80° C). If plastic laminates or cement are not sufficiently
heat-resistant, warping, bubbling or detachment of the finish may result.
For correct ventilation, follow the ventilation
opening directions shown in the figure (at least 500 x 80 mm). Also provide for at least 5 mm clearance between the top of the oven and the lower edge of the worktop. This space must not be obstructed by cross rails or other structural elements.
During oven installation, care must be taken to
ensure that the sides are not touching the front edges of the housing or adjacent drawers and doors (see picture).
Carry out the electrical connections between
cooktop and oven (see chapter “Electrical connection”).
Secure the oven to the kitchen unit with screws (A)
as shown.
4
No contacts
INSTALLATION
Cooktop
The cooktop must be set into a worktop between 20 mm and 50 mm thick. There must be nothing between the cooktop and the oven (cross rails, brackets, etc.).
If the cooktop is to be installed next to a column unit, leave a distance of at least 10 0mm from the edge of the cooktop to the side of the column unit.
Cut an opening in the worktop of the dimensions
shown in the Product Description Sheet supplied separately.
If not already present, fit the supplied seal to the
cooktop flange after cleaning the contact area as shown in the figure.
Cooktop with electric hotplates
If the worktop is made of wood, fit the supplied clips.
Position the 4 spring clips (B) and fit them in their
1.
locations on the underside of the cooktop. Fit the cooktop into the worktop.
2.
If the worktop is made of marble, plastic, ceramics, natural stone, etc.,
be secured with brackets (C) code 4819 310 18528 (to be requested from After Sales Service).
Position the brackets over the holes and secure
1.
them with the supplied screws. Fit the cooktop into the worktop.
2.
Glass-ceramic cooktop
Remove the protective film before installing the
N.B.:
cooktop.
If the worktop is made of wood,
spring clips and screws. Position the 4 clips (D) as shown and at the
1.
specified dimensions. Secure the clips using screws (E).
2.
Fit the cooktop into the worktop.
3.
If the worktop is made of marble, plastic, ceramics, natural stone, etc.
be secured with brackets (F) code 4819 404 78697 (to be requested from After Sales Service).
Fit the cooktop into the worktop.
1.
Position the 4 brackets (F) as shown in the figure,
2.
in accordance with the thickness of the worktop. Fix the 4 screws (G) in holes (H).
3.
the cooktop must
use the supplied
, the cooktop must
5
ELECTRICAL CONNECTION
Make sure the appliances are installed and connected to the electricity supply by a qualified technician in accordance with the manufacturers instructions and in compliance with local regulations.
The installer is responsible for the correct electrical connection of the appliances and the observance of the relative safety regulations.
Connecting the oven to the power supply
Make sure that the voltage shown on the rating
plate is the same as the power supply voltage in your home. The rating plate is on the front edge of the oven cavity (visible with oven door open). Use a type H05RR-F power cord (minimum
length 800 mm).
Warning: All the ovens components operate at 230-240 V. When using a 400 V connection, make sure that the voltage reaching the oven is 230-240 V, as illustrated in the side table.
Conductors X number
1N+
~
Connection
H05 RR-F 3X4 mm²
The appliance must be connected to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm.
The appliances must be earthed by law.
Do not use multiple plug adapters or
extension leads.
After the appliances have been installed, the electrical components must be inaccessible.
2N+
3+
3N+
~
~
~
H05 RR-F 4X2,5 mm²
H05 RR-F 4X2,5 mm²
H05 RR-F 5X1,5 mm²
Interconnecting cooktop and oven
Before connecting the oven to the power supply,
check that the cooktop is among the ones listed in the cooktop/oven pairing product sheet. Connect the 3 pole and 4 pole connectors to the respective connectors on the oven. The 3 pole connectors (H) is located at the rear
right hand side of the control panel, the 4 pole connector (J) is located at the top of the oven in the left hand corner (see figure). Connect the yellow/green striped earth wire ( )
(K) from the cooktop to the screw located near the 3 pole connector.
WARNING: DO NOT CONNECT TO THE POWER SUPPLY BEFORE YOU HAVE FINISHED CONNECTING THE OVEN AND COOKTOP.
Mount the oven in the kitchen unit.
Make sure the power cord is not trapped.
6
Loading...
+ 8 hidden pages