Whirlpool ADG 9427 INSTRUCTION FOR USE

Before using the dishwasher, read the user instructions!

ADG 9427

On button

Off button

Indicators

Add rinse aid

Add regeneration salt

Only add regeneration salt immediately
before starting a wash programme.

Quick Reference Guide

Programme selection button

The selected programme is shown in the
window of the display.

Start button

Switches “on” when the dishwasher is
operating. Flashes when a fault occurs.
Switches off at the end of the programme.

Reset button

After pressing the Reset button, the selected
programme and the supplementary functions
are cancelled (except the water hardness
setting, see user instructions) and must be
reset. On releasing the button this is
confirmed by an acoustic signal.

Options

GB

3)

Time and failure display

Indicates in hours the time remaining until the
start of the wash cycle. Toward the end of the
programme, during the drying cycle, the display
will indicate the time remaining in minutes.

“F....” Identification of faults for service

technician

“Delayed start” button

The wash cycle can be programmed to start
after 1 - 24 hours. With each successive touch of
the button, the delayed start indicator increases
by 1 hour , and after 24 returns to 00. Then press
the Start button. The dishwasher will start at the
set time.

“Half load - Multizone” button

Load the upper or lower rack
This function can be used with any programme.
Press once = upper rack
(the indication lamp/symbol comes on)
Press twice = lower rack
(the indication lamp/symbol comes on)
Press 3 times = Off (half load function
deactivated).
When washing without the top rack, press the
“Half Load” button twice, or “Lower rack wash”
(the corresponding LED/symbol comes on).

Antibacterial rinse

This function adds an antibacterial rinse at the end
of the wash cycle, thereby guaranteeing a perfectly
clean and sanitized load. The lamp will light up
when the function is activated. If the temperature
is not maintained during the antibacterial cycle (e.g.
if the door is opened and remains open for a long
time), the lamp will start blinking to indicate that
sanitation is not guaranteed.

4) 5)

only

.

Programme chart

Detergent

Programmes Loading instructions A B

Pre-Rinse cold

Quickwash 40°C

1) 5) 6)

Eco

Intensive

1) Reference programme for energy label EN 50242;

2) Refer to “User instructions”;

3) Programme data obtained in conformity with European
standard EN 50242. Values may vary in relation to usage,
e.g.: different loads, options, water temperatures - above
or below 15°C - as well as water hardness and power
supply voltage, etc.

Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address:
“[e-mail]”.

Whirlpool is a registered trademark of Whirlpool USA

50°C

5)

70°C

Crockery to be washed later. - - 4.0 0.03 14

Lightly soiled crockery with no
dried-on food.

Normally soiled crockery. X X 13.0 1.05 195

Recommended programme for
heavily soiled crockery, especially
suitable for pans and saucepans.

4) The bacteria removal efficiency has been tested by the
Institut Pasteur de Lille (France), based on the NF
EN 13697 standard of November 2001.

5) These programmes can be used with the Antibacterial
rinse option.

6) Energy saving programme with prolonged drying cycle.

(We reserve the right to make technical modifications)

X - 10.0 0.65 30

X X 14.0 1.55 155

2)

Consumption

Litres kWh Minutes

3)

5019 396 91636

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Open the door,

switch on the appliance

How to fill the

detergent dispenser

Check the rinse aid level

Check the regeneration

salt level

Load the racks

Select a programme

Press the ON button.

Compartment
With each wash cycle.
Compartment
For programmes with pre-wash only.
If using combined action dishwasher

tabs, follow the user instructions!

Mechanical indicator C.
Electric indicator on control panel (if provided).

On models with water softener
system only.

Mechanical indicator D. Electric
indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

The display shows the last programme selected.
Press P or until the selected programme lights up.

A:

B:

ABC

Select options

Press the Start button

Turn on the water tap

close the dishwasher door

Wash cycle

Switch off the appliance

Turn off the water tap,

unload the racks

If necessary (and if provided) the corresponding indicator lamp lights up.

The selected programme is
then memorised (even in the
event of power failure).

At the end of the programme an acoustic signal will sound and
appear on the display. Once the
all the indicator lights will switch off.

Warning: when the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

“Change programme in progress”

1. Press the “Reset” button.

2. Automatic drai ni ng approx. 30 sec.

3. Select a new programme.

4. Select the desired options again (except
“Set detergent” - if provided and “Water
hardness setting”).

5. Start the dishwasher again by pressing the
Start button.

- Only open the dishwasher if necessary
(Warning: beware of hot steam).

- If the appliance is switched off during a
wash cycle, when switched on again it
will resume the cycle from where it was
interrupted.

will

button has switched off: press

Start

“End”

OFF

,