Whirlpool ADG 7530 installation and maintenance instructions
Before using the dishwasher, read the installation and maintenance instructions carefully!
GB
ADG 7530
1. OVERVIEW
Programme selection button
Press the button (repeatedly) until the indicator lamp of
the desired programme lights up (see table 1.1).
At the end of the wash cycle, the last programme
selected is memorized.
Detergent setting upon initial use and when using a
different type of detergent
Indicator lamp off = Powder/gel detergent (factory
setting).
If using combined detergents, press and hold the
button for 3 seconds; the indicator lamp lights up =
rinse aid and salt indicators are deactivated.
From water hardness level 5, the salt indicator remains
active. At the end of the programme, the most recently
selected setting remains memorised.
Delayed Start button
Press the button repeatedly to delay the start of the
programme by 2, 4 or 8 hours. Then press the Start/Resume
button. The remaining time is indicated by the corresponding
indicator lamp. The wash programme will start after the set
time. The set delay will be memorised at the end of the cycle,
and can be selected by pressing the button again.
Start/Resume button
The indicator lamp lights up during operation, flashes
when the programme is interrupted before completion
and switches off at the end of the programme.
Cancel/Off button
Press the button to switch the dishwasher off or to
interrupt the selected programme.
If the Cancel/Off indicator lamp flashes repeatedly, this
indicates a fault: see chapter 5 “What to do if...”.
Salt level indicator and rinse aid level indicator
These light up at the end of the programme if salt or
rinse aid needs topping up. Only add just before
starting a wash cycle.
Table 1.1.
Programme Table
Selectable
P
1
2
3
4
5
1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to
different loads, extra functions, different settings, water supply temperatures, water hardness and power supply voltage.
2) Programme for energy data label in conformity with EN 50242. - Information for Test Laboratories:
EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
Programmes
Pre-Rinse cold
Quickwash 45°C
2)
Eco
Intensive 70°C
Half Load 50°C
50°C
additional
options
Description of programme
Crockery to be washed later.
Lightly soiled crockery, with no
dried-on food.
Normally soiled crockery. Energysaving programme.
Recommended programme for
heavily soiled crockery, especially
suitable for pots and pans.
Ideal for washing a half load of lightly
or normally soiled crockery.
Detergent
compartment
large small Litres kWh Minutes
Consumption
— — 4,0 0,03 14 ±
X — 11,0 0,80 30 ±
X X 12,0 1,05 165 ±
X X 14,0 1,55 155 ±
X X 10,0 1,04 145 ±
for detailed information on the
1)
1)
1)
1)
1)
1)
Whirlpool is a registered trademark of Whirlpool USA
5019 396 01199
1
2. QUICK REFERENCE GUIDE
Detailed instructions are given on the following pages; also see section “5. What to do if...”.
1. Switch the
appliance on
2. Select the right type
of detergent
3. Fill the detergent
dispenser
4. Check the rinse aid level
5. Set the water
hardness level
Programme
selection
button
The dishwasher switches on automatically when any button is pressed, except for the
button. If no button is pressed within 30 seconds, the appliance switches to Energy
Saving mode.
Depending on the dishwasher model
Programme
selection
button
6. Check the salt level
7. Load the racks
8. Turn on the water
tap, close the door
9. Select a programme,
and start
Wash cycle
Programme
selection
button
Fill crockery: beware of hot steam! The
start indicator blinks, close the door, press
the Start button again, the programme
resumes from where it had stopped (as
happens after a power shortage as well).
Change the programme
in progress:
- Press the “Cancel/Off” button.
- (Water drains for up to 60
seconds).
- Select a new programme.
- Press the START button.
10.End of programme
11.Open the door
12.Turn off the water tap,
unload the racks
2
3. HOW TO USE THE APPLIANCE
HOW TO FILL THE DETERGENT DISPENSER
Only fill the detergent dispenser prior to starting a wash programme.
specially recommended for dishwashers, observing the manufacturer’s recommended dosage.
Observe the manufacturer’s safety warnings!
Press the left button (button 1) on the dispenser to open the detergent dispenser compartments.
a. Powder/gel/tabs
Fill the detergent dispenser compartments in accordance with the wash programme selected (table 1.1).
Programmes without pre-wash:
Pour the entire recommended dosage into compartment A.
Programmes with pre-wash:
Pour 2/3 of the recommended dosage into the large compartment
and 1/3 into the small compartment B.
A
Dishwasher tabs should be placed, as per the manufacturer’s
recommendations, in compartment A.
If the “Half load” option is selected, detergent dosage should be
reduced by approximately 1/3.
b. Combined action detergents (2 in 1/3 in 1/... etc.)
Dishwasher tabs should be placed, as per the manufacturer’s
recommendations, in compartment A.
Shut and firmly press the detergent compartment lid shut after filling.
Detergents with rinse aid incorporated may be effective only with longer programmes. In the
case of shorter programmes, detergent residue may be a problem (if necessary, use powder
detergent). Detergents with rinse aid incorporated tend to form excess suds.
Large
compartment
A
use detergents
Only
Button
1
compartment
Small
B
The guarantee is not applicable if faults are caused by the use of these products.
HOW TO CHECK/FILL/ADJUST RINSE AID
Not necessary when using a combined action detergent.
a. How to check the rinse aid level
Check the visual indicator C on the dispenser: dark = sufficient rinse aid, clear = add rinse aid.
In the case of appliances with an electric indicator on the
control panel, the rinse aid indicator lights up at the end
of the wash cycle when rinse aid needs to be added.
b. How to fill the rinse aid dispenser
Press the right button on the dispenser (button 2 ) to open
the rinse aid compartment.
Fill the dispenser with rinse aid up to the “max” line
(approx. 150 ml).
Shut the lid again.
Only use rinse aids recommended for use in domestic dishwashers.
If rinse aid is accidentally spilt,
which could cause appliance malfunctioning.
c. How to adjust the rinse aid dosage regulator:
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less
rinse aid is dispensed (factory setting: position 4).
Press the button 2 to open the cover.
Using a coin or similar object, turn the arrow to the desired setting.
After adjusting the rinse aid setting, shut the cover again.
immediately
remove it to avoid the formation of excessive suds
Indicator
max
Button
C
2
If the dishes often have whitish streaks: reduce the dosage by turning the dial to a lower setting
(1-3). Dishes did not dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic
dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
3
Loading...