Before using the dishwasher, read the installation and maintenance instructions carefully!
GB ADG 6560
1. OVERVIEW
Programme selection button
Press the button (repeatedly) until the indicator lamp of the desired programme lights up (see table 1.1).
At the end of the wash cycle, the last programme selected is memorised. Delayed start button
Press the button repeatedly to delay the start of the programme by 2, 4 or 8 hours. Then press the Start/Resume button. The remaining time is indicated by the corresponding indicator lamp.
The wash programme will start after the set time. The set delay will be memorised at the end of the cycle, and can be selected by pressing the button again.
Start/Resume button
The indicator lamp lights up during operation, flashes when the programme is interrupted before completion and switches off at the end of the programme.
Table 1.1.
Cancel/Off button
Press the button to switch the dishwasher off or to interrupt the selected programme.
If the Cancel/Off indicator lamp flashes repeatedly, this indicates a fault: see chapter 5 “What to do if...”.
Salt level indicator and rinse aid level indicator These light up at the end of the programme if salt or rinse aid needs topping up.
Only add just before starting a wash cycle.
P
1
2
3
4
5
Programme Table
Programmes |
Available |
Description of programme |
|
options |
|
Pre-Rinse cold |
|
Crockery to be washed later. |
Quickwash 40°C
Eco 2) |
50°C |
Antibacterial 3)
Lightly soiled crockery, with no dried-on food.
Normally soiled crockery.
Energy-saving programme.
Normally - heavily soiled crockery, with additional antibacterial wash. Stopping a programme underway (e.g. by opening
the door) can compromise the elimination of bacteria.
Recommended programme for Intensive 70°C 
heavily soiled crockery, especially
suitable for pots and pans.
Detergent |
Consumption 1) |
||||||||
dispenser |
|||||||||
|
|
|
|
|
|||||
large |
|
small |
Litres |
|
kWh |
|
Minutes |
||
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
- |
|
- |
5.0 |
|
0.02 |
|
10 ± 1) |
||
|
|
|
|
|
|
|
|
|
|
X |
|
- |
13.0 |
|
0.70 |
|
30 ± 1) |
||
|
|
|
|
|
|
|
|
|
|
X |
|
X |
15.0 |
|
1.05 |
|
165 ± 1) |
||
|
|
|
|
|
|
|
|
|
|
X |
|
X |
16.0 |
|
1.75 |
|
120 ± 1) |
||
|
|
|
|
|
|
|
|
|
|
X |
|
X |
15.0 |
|
1.50 |
|
140 ± 1) |
||
|
|
|
|
|
|
|
|
|
|
1)Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads, extra functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness and power supply voltage.
2)Programme for energy data label in conformity with EN 50242. - Information for Test Laboratories: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3)The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on Standard NF EN 13697 - November 2001.
Whirlpool is a registered trademark of Whirlpool USA |
5019 396 01184 |
1
2. QUICK REFERENCE GUIDE
Detailed instructions are given on the following pages; also see section “5. What to do if...”.
1.Switch the appliance on
2.Select the right type of detergent
3.Fill the detergent dispenser
The dishwasher switches on automatically when any button is pressed, except for the 
button. If no button is pressed within 30 seconds, the appliance switches to Energy
Saving mode.
Depending on the dishwasher model
4. Check the rinse aid level
5. Set the water
Programme
hardness level selection
button
6. Check the salt level
7.Load the racks
8.Turn on the water tap, close the door
9.Select a programme, and start
Wash cycle
Programme selection button
Fill crockery: beware of hot steam! The start indicator blinks, close the door, press the Start button again, the programme resumes from where it had stopped (as happens after a power shortage as well).
Programme selection button
Change the programme in progress:
-Press the “Cancel/Off” button.
-(Water drains for up to 60 seconds).
-Select a new programme.
-Press the START button.
10.End of programme
11.Open the door
12.Turn off the water tap, unload the racks
2
3. HOW TO USE THE APPLIANCE
HOW TO FILL THE DETERGENT DISPENSER
Only fill the detergent dispenser prior to starting a wash programme. Only use detergents specially recommended for dishwashers, observing the manufacturer’s recommended dosage. Observe the manufacturer’s safety warnings!
Press the left button (button 1) on the dispenser to open the detergent dispenser compartments.
a. Powder/gel/tabs
Fill the detergent dispenser compartments in accordance with the wash programme selected (table 1.1).
Programmes without pre-wash:
Pour the entire recommended dosage into compartment A. Programmes with pre-wash:
Pour 2/3 of the recommended dosage into the large compartment A and 1/3 into the small compartment B.
Dishwasher tabs should be placed, as per the manufacturer’s recommendations, in compartment A.
If the “Half load” option is selected, detergent dosage should be reduced by approximately 1/3.
b. Combined action detergents (2 in 1/3 in 1/... etc.)
Dishwasher tabs should be placed, as per the manufacturer’s recommendations, in compartment A.
Shut and firmly press the detergent compartment lid shut after filling.
Large |
Button 1 |
Small |
compartment A |
compartment B |
|
Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.
The guarantee is not applicable if faults are caused by the use of these products.
HOW TO CHECK/FILL/ADJUST RINSE AID
Not necessary when using a combined action detergent.
a. How to check the rinse aid level
Check the visual indicator C on the dispenser: dark = sufficient rinse aid, clear = add rinse aid.
In the case of appliances with an electric indicator on the |
Indicator C |
|
control panel, the rinse aid indicator |
lights up at the end |
|
of the wash cycle when rinse aid needs to be added.
b. How to fill the rinse aid dispenser |
|
|
max |
Press the right button on the dispenser (button 2 ) to open |
|
|
|
the rinse aid compartment. |
|
|
|
Fill the dispenser with rinse aid up to the “max” line |
|
|
|
(approx. 150 ml). |
|
|
Button 2 |
Shut the lid again. |
|
|
|
|
|
|
Only use rinse aids recommended for use in domestic dishwashers.
If rinse aid is accidentally spilt, immediately remove it to avoid the formation of excessive suds which could cause appliance malfunctioning.
c. How to adjust the rinse aid dosage regulator:
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4).
Press the button 2 to open the cover.
Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
If the dishes often have whitish streaks: reduce the dosage by turning the dial to a lower setting (1-3). Dishes did not dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
3
Loading...